Fisher & Paykel WB60S Series User manual

Warming Drawer
WB60S
models
NZ AU GB IE
INSTALLATION INSTRUCTIONS
590513E 05.16
www.fisherpaykel.com

1
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
1SAFETY AND WARNINGS
WARNING!
Electrical Shock Hazard
Before carrying out any work on the
electrical section of the appliance,
it must be disconnected from the
mains electricity supply.
Connection to a good earth wiring
system is absolutely essential and
mandatory.
Alterations to the domestic wiring
system must only be made by a
qualified electrician.
Failure to follow this advice may
result in electrical shock or death.
WARNING!
Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result in
injury or cuts.
WARNING!
Fire hazard
Do not use adapters, reducers, or
branching devices to connect this
appliance to the mains power supply.
Failure to follow this advice may
result in overheating, burning, or fire.
!
!
!
IMPORTANT SAFETY INSTRUCTIONS!
 To reduce the risk of fire, electrical
shock, injury to person, or damage
when using the warming drawer,
please read these instructions
carefully before installing this product.
 Please make this information available
to the person installing the product –
doing so may reduce your installation
costs.
 Installation work, maintenance and
repairs may only be carried out by
suitably qualified and competent
persons in accordance with national
and local safety regulations.
 Always disconnect the power supply
prior to carrying out any installation,
maintenance or repair work.
 Before installation make sure that
the voltage and frequency listed on
the data plate corresponds with the
household electrical supply.

2
1SAFETY AND WARNINGS
 When installing companion products
the weight of the companion product
should be distributed across the edges
of the warming drawer. Products
above which rest on “feet” may only
be installed if the feet of the product
lie within 70mm of the sides of
the warming drawer, as this area is
reinforced. Failure to do this may result
in damage to the warming drawer and
companion product.
 Before installing the warming drawer
you must inspect it for any signs of
damage. Under no circumstances
should you install or use the warming
drawer if it has been damaged.
 If the power supply cord is damaged, it
must be replaced by the manufacturer,
its service agent or a similarly qualified
tradesperson in order to avoid a hazard.
 Connect the warming drawer to a
properly rated, protected and sized
power supply circuit to avoid electrical
overload.
 Do not use an extension cord or a
portable electrical outlet device (e.g.
multi-socket outlet box) to connect the
Warming Drawer to the power supply.
Make sure the power supply cord is
located so that it will not be stepped
on, tripped over or otherwise subject to
damage or stress.
 Ensure the connection to power supply
is accessible after installation.
IMPORTANT SAFETY INSTRUCTIONS!
 The electrical outlet should be easily
accessible after installation.
 When a companion product is installed
in combination with the warming drawer
to the same circuit, operating both
products may cause an overload. If in
doubt consult a qualified electrician.
 When installed in combination with
a companion product the companion
product may be placed directly onto
the warming drawer. It is not necessary
to place a shelf between the products.
A built- in shelf at the base of the
cabinetry able to support the weight of
both products is required.
 If installing the warming drawer directly
underneath an oven, ensure you do
not damage the oven’s lower trim. The
lower trim ensures correct air circulation
to the oven and allows the door to
open and close without obstruction.
Fisher & Paykel does not accept any
responsibility for any damage resulting
from incorrect installation.
 The maximum weight the warming
drawer is able to support is 60 kg.
 The warming drawer is not designed
for use in mobile installations such as
recreational vehicles, boats or aircraft.

3
3PRIOR TO INSTALLATION
 The cavity is square and level, and of the required dimensions.
 The installation will comply with all clearance requirements and applicable standards and regulations.
 The power switch will be easily accessible to the customer when the warming drawer is installed.
 The warming drawer (and any product on top of it) will rest on a surface that can support its weight.
 The height from the floor suits the customer.
 You consult local building authorities and by-laws if in doubt regarding installation.
If installing with a companion product
IMPORTANT!
 If installing with a companion product please refer to the installation instructions of that product to ensure the installation requirements of BOTH products are met.
 When installing products on top of the warming drawer, the weight of the product should be distributed across the edges of the warming drawer.
 Products above which rest on “feet” may only be installed if the feet of the product lie within 70mm of the sides of the warming drawer, as this area is reinforced.
Failure to do this may result in damage to the warming drawer and companion product.
Screws (4) Anti-tip bracket (1) Oven support brackets (2)
Warming Drawer can withstand
a maximum weight of 60kg
70mm 70mm
Feet
A
B
C
D
F
G
M
M
M
N
N
O
O
H
I
J
K
L
E
M
M
M
N
O
2PARTS SUPPLIED

4
B
D
A
C
H
CJ
K
F G
D
E
H
I
4PRODUCT DIMENSIONS
PLAN
FRONT
Terminal Block
SIDE
PRODUCT DIMENSIONS mm
AOverall height of product 118
BOverall width of product 596
CDepth of drawer front panel (excluding handle)* 19
DDepth of chassis (including terminal block) 536
EWidth of chassis at rear 551
FHeight from bottom drawer panel to bottom of chassis at rear 16
GHeight from bottom of drawer panel to top of chassis 118
HDepth of drawer (open) (measured from front of drawer) 455
IHeight of drawer front panel 116
JDepth of handle measured from front of drawer 41
KWidth of handle 565

5
5A CABINETRY DIMENSIONS - UNDERBENCH (IE INSTALLED WITH A F&P 60CM WIDE SINGLE OVEN)
A
B
C
D
F
G
M
M
M
N
N
O
O
H
I
J
K
L
E
M
M
M
N
O
A
B
C
D
F
G
M
M
M
N
N
O
O
H
I
J
K
L
E
M
M
M
N
O
A
B
C
D
F
G
M
M
M
N
N
O
O
H
I
J
K
L
E
M
M
M
N
O
**
720mm
Warming Drawer
Warming Drawer
Oven
Oven
*PO
Ta b
Oven support bracket
Fit the supplied oven support brackets
Unscrew-fit-
rescrew
THE FOLLOWING PAGES DETAIL COMMON CABINETRY SCENARIOS
IMPORTANT!
If installing under an oven, you must first fit the two
supplied Oven support brackets to the sides of the
Warming Drawer. The brackets help support the rear of
the oven.
Unscrew the 3 top screws on each side, fit the brackets
with the tabs facing inwards as shown and screw back in.
Note: The screws may not be identical.
Replace each screw into its original hole position.
Oven
support
brackets
PLAN
SIDE
CABINETRY DIMENSIONS mm
MMinimum inside height of cavity (with F&P 60cm wide single oven) 687
NInside width of cavity 560
OMinimum inside depth of cavity 565
Note: When installed in combination with a companion product the companion product may be placed directly onto the
warming drawer. It is not necessary to place a shelf between the products. A built- in shelf at the base of the cabinetry able
to support the weight of both products is required.
* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product.
** In some instances the front cabinetry rail may need to be removed to enable installation.

6
A
B
C
D
F
G
M
M
M
N
N
O
O
H
I
J
K
L
E
M
M
M
N
O
A
B
C
D
F
G
M
M
M
N
N
O
O
H
I
J
K
L
E
M
M
M
N
O
5B CABINETRY DIMENSIONS - WALL MOUNTED (IE INSTALLED WITH A F&P COMPACT OVEN)
600mm
*PO
Ta b
Unscrew-fit-
rescrew
PLAN
SIDE
CABINETRY DIMENSIONS mm
MMinimum inside height of cavity
with optional Lower trim kit fitted
without optional Lower trim kit fitted
590
570
NInside width of cavity 560
OMinimum inside depth of cavity 565
Note: When installed in combination with a companion product the companion product may be placed directly onto the
warming drawer. It is not necessary to place a shelf between the products. A built- in shelf at the base of the cabinetry able
to support the weight of both products is required.
* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product.
Compact Oven
Compact Oven
Cabinet below
Additional 18 mm Wood Spacer
Warming Drawer
Lower trim kit
(optional, supplied separately)
Compact oven
IMPORTANT!
In a wall mounted installation,
there needs to be an 18 mm
Spacer fixed underneath the
warming drawer first to raise
it to the required height.
Warming Drawer
Warming Drawer

7
A
B
C
D
F
G
M
M
M
N
N
O
O
H
I
J
K
L
E
M
M
M
N
O
A
B
C
D
F
G
M
M
M
N
N
O
O
H
I
J
K
L
E
M
M
M
N
O
5C CABINETRY DIMENSIONS - WALL MOUNTED (IE INSTALLED WITH A F&P COFFEE MAKER)
600mm
45mm
*PO
PLAN
SIDE
CABINETRY DIMENSIONS mm
MMinimum inside height of cavity
with optional Lower trim kit fitted
without optional Lower trim kit fitted
590
570
NInside width of cavity 560
OMinimum inside depth of cavity 565
Note: When installed in combination with a companion product the companion product may be placed directly onto the
warming drawer. It is not necessary to place a shelf between the products. A built- in shelf at the base of the cabinetry able
to support the weight of both products is required.
* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product.
Additional 18mm Wood Spacer IMPORTANT!
In a wall mounted installation,
there needs to be an 18mm
Spacer fixed underneath the
warming drawer first to raise
it to the required height.
Warming Drawer
Warming Drawer
Coffee Maker
Coffee Maker
Warming Drawer
Lower trim kit
(optional, supplied separately)
Coffee Maker
Side rail IMPORTANT!
When installing under an F&P Coffee Maker
you must ensure the supplied anti-tip
bracket is installed, unless there is a fixed
shelf above the drawer acting as an anti-tip
obstacle.
Anti-tip Bracket
Supplied Anti-tip Bracket
(screwed to the back wall)
IMPORTANT!
If installing under the F&P Coffee Maker, ensure there
is the 45mm gap at the back of the cabinet and the
200mm2toekick cutout required for airflow.
Refer to the Coffee Maker Install instructions.

8
A
B
C
D
F
G
M
M
M
N
N
O
O
H
I
J
K
L
E
M
M
M
N
O
A
B
C
D
F
G
M
M
M
N
N
O
O
H
I
J
K
L
E
M
M
M
N
O
A
B
C
D
F
G
M
M
M
N
N
O
O
H
I
J
K
L
E
M
M
M
N
O
5D CABINETRY DIMENSIONS - WALL MOUNTED (STANDALONE)
120mm
*PO
PLAN
SIDE
CABINETRY DIMENSIONS mm
MInside height of cavity 120
NInside width of cavity 560
OMinimum inside depth of cavity 545
* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product.
Additional 18mm Wood Spacer IMPORTANT!
In a wall mounted
installation, there needs
to be an 18mm Spacer
fixed underneath the
warming drawer first to
raise it to the required
height.
Warming Drawer
Supplied Anti-tip Bracket
(screwed to the back wall)
Fixed shelf
IMPORTANT!
In a standalone wall mounted installation, you
must ensure that the supplied anti-tip bracket
is installed unless there is a fixed shelf above
acting as an anti-tip obstacle.
Steam Oven
Cabinet below
Cabinet above
Warming Drawer

9
1
2
1
2
3
6DISCARD PACKAGING RESPONSIBLY
7MARK AND PRE-DRILL THE HOLES FOR SECURING THE WARMING DRAWER
8CONNECT THE WARMING DRAWER TO THE MAINS SUPPLY
Recycle responsibly
Unpack the warming drawer and inspect for any signs of damage.
Do not install the warming drawer if it has been damaged.
IMPORTANT!
Packing materials (e.g. plastic bags, polystyrene foam, staples,
packing straps etc) and tools should not be left around during
and after installation, especially if they are within easy reach of
children, as they may cause serious injuries.
IMPORTANT!
 All electrical work may only be carried out by suitably qualified and competent persons in accordance with national and
local safety regulations.
 This warming drawer must be earthed.
Before placing the warming drawer into the cavity, route the power cord into the back of the cavity and plug it in to the
switched socket. The switched socket should be in an easily accessible area within 900mm of the centre rear of the product.
Power requirements
Model Code Power Voltage Wattage
WB60SD 1.6 - 1.8 A 220-240 V 360-420W
IMPORTANT!
Do not lift the warming drawer by the drawer handle.

10
1Ensure the warming drawer is level and positioned in place in the cavity.
IMPORTANT!
Do not lift the warming drawer by the drawer handle.
2Fully open the drawer.
3Fasten the warming drawer in place with the two screws supplied, through the
front trim, beneath the drawer. Do not overtighten the screws.
If the anti-tip bracket is required (see example scenarios) first secure the product at the
front, then place the bracket centrally at the back of the cavity, sitting it on the top of
the chassis. Secure it to the rear cabinet wall using the screws provided.
9SECURE THE WARMING DRAWER TO THE CABINETRY
!0 SECURE THE ANTI-TIP BRACKET (OPTIONAL DEPENDING ON CABINETRY CONFIGURATION)

11
!1 FINAL CHECKLIST
TO BE COMPLETED BY THE INSTALLER
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date
Make sure the warming drawer is level and securely fitted to the cabinetry.
Make sure any internal packaging has been removed from the drawer.
Make sure that the isolating switch is accessible by the customer.
Make sure the anti-tip bracket has been fitted correctly if it is required.
If installing an oven directly on top of the warming drawer, make sure the supplied oven
support brackets have been fitted to the warming drawer.
TEST OPERATION:
Open the drawer and press the
1h
2h
1h
2h
1h
2h
1h
2h
FP WARMER DRAWER INTERFACE LOGIC_V1
PRODUCT OFF
THE THREE TEMPERATURE BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER TWO BUTTONS SHOW WHITE
THE TWO TIMER BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER BUTTON SHOWS WHITE
ICE AND WATER INTERFACE COMPONENTS
All bezels capable of glowing white and red
except fot the on /o bezel which only needs
to glow red.
Component Layout As Shown.
USER PRESSES ON/OFF BUTTON
ALL OTHER BEZELS GLOW WHITE EXCEPT
TEMPERATURE SETTING WHICH IS PRESET TO
MEDIUM AND GLOWS RED (PRODUCT STARTS
HEATING TO THE MEDIUM TEMPERATURE)
ON/OFF GLOWS RED UNTIL BUTTON IS PRESSED
AGAIN SHUTTING THE PRODUCT OFF.
WHEN THE TIMER BUTTON IS PRESSED THE
PRODUCT IS SET TO RUN FOR THE ALLOWED
TIME.
WHEN THIS TIME RUNS OUT THE PRODUCT SHUTS
OFF.
1h
2h
1h
2h
button to turn the warming drawer on.
The on/off halo and temperature setting 2 (
1h
2h
1h
2h
1h
2h
1h
2h
FP WARMER DRAWER INTERFACE LOGIC_V1
PRODUCT OFF
THE THREE TEMPERATURE BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER TWO BUTTONS SHOW WHITE
THE TWO TIMER BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER BUTTON SHOWS WHITE
ICE AND WATER INTERFACE COMPONENTS
All bezels capable of glowing white and red
except fot the on /o bezel which only needs
to glow red.
Component Layout As Shown.
USER PRESSES ON/OFF BUTTON
ALL OTHER BEZELS GLOW WHITE EXCEPT
TEMPERATURE SETTING WHICH IS PRESET TO
MEDIUM AND GLOWS RED (PRODUCT STARTS
HEATING TO THE MEDIUM TEMPERATURE)
ON/OFF GLOWS RED UNTIL BUTTON IS PRESSED
AGAIN SHUTTING THE PRODUCT OFF.
WHEN THE TIMER BUTTON IS PRESSED THE
PRODUCT IS SET TO RUN FOR THE ALLOWED
TIME.
WHEN THIS TIME RUNS OUT THE PRODUCT SHUTS
OFF.
1h
2h
1h
2h
) halo should glow red.
Shut the drawer.
After 5-10 minutes open the drawer. The internal surfaces of the drawer should feel
slightly warmed.
Press the
1h
2h
1h
2h
1h
2h
1h
2h
FP WARMER DRAWER INTERFACE LOGIC_V1
PRODUCT OFF
THE THREE TEMPERATURE BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER TWO BUTTONS SHOW WHITE
THE TWO TIMER BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER BUTTON SHOWS WHITE
ICE AND WATER INTERFACE COMPONENTS
All bezels capable of glowing white and red
except fot the on /o bezel which only needs
to glow red.
Component Layout As Shown.
USER PRESSES ON/OFF BUTTON
ALL OTHER BEZELS GLOW WHITE EXCEPT
TEMPERATURE SETTING WHICH IS PRESET TO
MEDIUM AND GLOWS RED (PRODUCT STARTS
HEATING TO THE MEDIUM TEMPERATURE)
ON/OFF GLOWS RED UNTIL BUTTON IS PRESSED
AGAIN SHUTTING THE PRODUCT OFF.
WHEN THE TIMER BUTTON IS PRESSED THE
PRODUCT IS SET TO RUN FOR THE ALLOWED
TIME.
WHEN THIS TIME RUNS OUT THE PRODUCT SHUTS
OFF.
1h
2h
1h
2h
button to turn the warming drawer off and shut the drawer.

12

590513 E 05.16
www.fisherpaykel.com
Copyright © Fisher & Paykel Appliances 2016. All rights reserved.
The product specifications in this booklet apply to the specific products
and models described at the date of issue. Under our policy of continuous
product improvement, these specifications may change at any time. You
should therefore check with your Dealer to ensure this booklet correctly
describes the product currently available.
NZ AU GB IE