Fisher & Paykel OD30WDX2 User manual

Installation Instructions
Specifications
Dimensions (Front View) Dimensions (Side View)
Fig. 02
Fig. 03
Base Cabinet Installation
Cut Out Dimensions
• The cabinet depth from the outer edge of the face
frame to the inside back of the cabinet or wall
should be at least 24” (see Fig. 04).
https://producthelp.fisherpaykel.com/us/Cook/Built-In_Ovens/Single/OD30WDX2/User_Guide_OD30WDX2/03_installation_in…
Updated: Sun, 14 Jun 2020 18:16:52 GMT
Powered by
1

Cut Out Dimensions
• The Warming Drawer should be installed into a
base cabinet with minimum outside dimensions of
13-1/4” high by 30” wide by 24” deep.
• Power supply required: 120Volts AC; 5 Amp min.,
15 Amp maximum circuit requirement.
Fig. 04
Wall Cabinet Installation
DOUBLE Wall Oven and Warming Drawer Installation SINGLE Wall Oven and Microwave and Warming
Drawer Installation
Fig. 05
https://producthelp.fisherpaykel.com/us/Cook/Built-In_Ovens/Single/OD30WDX2/User_Guide_OD30WDX2/03_installation_in…
Updated: Sun, 14 Jun 2020 18:16:52 GMT
Powered by
2

DOUBLE Wall Oven and Warming Drawer Installation SINGLE Wall Oven and Microwave and Warming
Drawer Installation
Fig. 06
**The floor of the opening should be constructed of plywood strong enough to support the
weight of the Warming Drawer (or use 2x4 construction - see fig. 04)
STEP 1 Removing the Drawer
Turn the unit off. Be sure the drawer is cool and no food items or trays are in the drawer. Never attempt to remove the
drawer while the unit is on or warm.
1. To remove the drawer, first remove plates, trays, etc., from the drawer.
2. Pull the drawer open towards you all the way until it reaches the stop position (Fig. 07).
3. Unlock the drawer by lifting up the tab on the left hand side (Fig. 08) and pressing down the tab on the right
hand side (Fig. 09) while pulling the drawer open at the same time (Fig. 10).
4. Keep pulling the drawer open until the slides are separated.
Removing the drawer for the very first time does require extra force.
https://producthelp.fisherpaykel.com/us/Cook/Built-In_Ovens/Single/OD30WDX2/User_Guide_OD30WDX2/03_installation_in…
Updated: Sun, 14 Jun 2020 18:16:52 GMT
Powered by
3

Fig. 07
Fig. 09
Fig. 08
Fig. 10
STEP 2 Mounting Installation of Chassis
The lower rear corners of the cabinet need to provide proper support to the back of the Warming Drawer and the anti-tip
mounting clips. A 120 volt AC outlet should be located no further than 36 inches from the back right corner of the
Warming Drawer.
The bottom rear section of the cabinet should be made of solid plywood or two 2x4 beam. It holds the anti-tip mounting
clips and supports the weight of Warming Drawer, which is 90 lbs. (see Fig.11 and 12). If two 2 x 4 beams are used, the
distance between their centers must be 20” to be able to secure the Warming Drawer.
1. Use the screws provided and attach the mounting clips. They must be installed for anti-tip safety to the bottom
https://producthelp.fisherpaykel.com/us/Cook/Built-In_Ovens/Single/OD30WDX2/User_Guide_OD30WDX2/03_installation_in…
Updated: Sun, 14 Jun 2020 18:16:52 GMT
Powered by
4

support at the back. See placement dimensions in figure below (see Fig.11).
2. Plug power cord into AC outlet. Slide the body onto the anti-tip mounting clips (see Fig.12).
3. Use the two supplied 1-1/2” long screws through the two embossed holes (see Fig.13) to secure the front of the
Warming Drawer.
Fig.11
Fig.12
Fig.13
https://producthelp.fisherpaykel.com/us/Cook/Built-In_Ovens/Single/OD30WDX2/User_Guide_OD30WDX2/03_installation_in…
Updated: Sun, 14 Jun 2020 18:16:52 GMT
Powered by
5

STEP 3 Replacing the Drawer
• With the drawer removed, the heating element is exposed.
• Never turn the unit on while the drawer is removed.
• Never let children play near or touch the warming drawer while it is not safely installed.
• Push the slides back into the cabinet while the drawer is removed to prevent accidents.
1. To reinstall the drawer, push the slides fully inside.
2. Position the drawer in front of the cavity and align the slides (Fig. 14).
3. With the slides aligned, push the drawer all the way inside (Fig. 15).
When the drawer is re-installed, the slides may feel stiff and hard to push in. This is normal. Pull the
drawer back out to realign the rollers. The drawer should now feel smooth and free.
Fig. 14
Fig. 15
https://producthelp.fisherpaykel.com/us/Cook/Built-In_Ovens/Single/OD30WDX2/User_Guide_OD30WDX2/03_installation_in…
Updated: Sun, 14 Jun 2020 18:16:52 GMT
Powered by
6

Adjusting the Latch
The latch can be repositioned vertically by adjusting the
two torx screws. The force necessary to open and close
the drawer can be changed by adjusting the two flathead
screws (Fig. 16).
Fig. 16
https://producthelp.fisherpaykel.com/us/Cook/Built-In_Ovens/Single/OD30WDX2/User_Guide_OD30WDX2/03_installation_in…
Updated: Sun, 14 Jun 2020 18:16:52 GMT
Powered by
7