Fisher manufacturing company 1848 User manual

fisher manufacturing company
fisher manufacturing company - toll free: 800-421-6162 fax: [phone]
ANSI/A112.18.1M, ANSI/NSF 61.9
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food service
industry. For three generations, the Fisher family has
adhered to a strict dedication of and overall value.
When you install Fisher products… you install the best.
Our hardware is manufactured with the standardization
of internal mechanisms. All chrome plating is triple
plated copper, nickel and chrome for durability. Every
piece of equipment we make is rigorously tested in
both our modern in-house testing center and in actual
field situations under extreme conditions. Every detail
is thoroughly checked. Before we make our products
available to you, they pass each and every test. You get
proven performance. Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge to
you, provided that the entire product is delivered to
Fisher Manufacturing Company. All transportation and
insurance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty claim.
This warranty does not cover external finish (except at
date of original purchase) or labor costs not specifically
authorized by Fisher Manufacturing Company.
A full and complete copy of our One Year limited
warranty is available upon request.
WARNING:
Proposition 65 requires that we provide you with the
following notice: “This product Contains A Chemical
Known To The State Of California To Cause Birth
Defects Or Other Reproductive Harm.”
8” C/C Deck Mount Gooseneck Faucet
Product Installation Guide
#1821 - 8” c/c Deck Mount Faucet with 6” Swivel
Gooseneck Spout
#1848 - 8” c/c Deck Mount Faucet with 6” Rigid
Gooseneck Spout
#3315 - 8” c/c Deck Mount Faucet with 12” Swivel
Gooseneck Spout
#3316 - 8” c/c Deck Mount Faucet with 12” Rigid
Gooseneck Spout
www.fisher-mfg.com
KEEP THIS MANUAL FOR FUTURE REFERENCE
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
[phone], FAX: [phone]
www.fisher-mfg.com
Replacement Parts for Deck Mount Faucets
PART NO. 39225 REV. A
1792
ANGLE STOP
WITH KEY
1790-1
ANGLE STOP
W/ CROSS
HANDLES
10014 (24”)
10022 (36”)
SUPPLY LINE
1/2” F X 1/2” F
10049 (24”)
10006 (36”)
SUPPLY LINE
1/2” M X 1/2” F
3300
CONTROL VALVE
2300
CONTROL VALVE
3965
12” SWIVEL
GOOSENECK
SPOUT
3966
12” RIGID
GOOSENECK
SPOUT 3969
6” RIGID
GOOSENECK
SPOUT
3968
6” SWIVEL
GOOSENECK
SPOUT
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
2000-2301
LEVER HANDLE
2000-3002
BIBB CAP
10464
DUCK GASKET
2000-5000
WASHER
3000-0010
LH SWIVEL STEM
OR
3000-0011
RH SWIVEL STEM
1000-7502
SCREW
10456
LUBE
3000-0000
RH SWIVEL STEM
REPAIR KIT
OR
3000-0001
LH SWIVEL STEM
REPAIR KIT
2000-5003
SEAT WASHER
1000-8002
SLIP JOINT KIT

PST
Installation Instructions for Deck Mount Faucets
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Notes:
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.
Tools Required for Installation
• Medium Sized Crescent Wrench
• Pipe Thread Sealant
Installation Instructions
1. Mount control valve on deck by inserting nipples through pre-drilled 7/8” holes in deck. Apply
thread sealant to both nipples and attach slip joint kits. Tighten until control valve is secure.
Attach supply lines as required.
2. If installing a swivel spout, apply lube to the o-rings on the gooseneck spout. Make sure the
white snap ring is in place before mounting the spout. Mount the spout and tighten the goose-
neck spout nut onto the faucet spout outlet. If installing a rigid spout, apply thread sealant to
male threads on spout and insert into control valve. Tighten until secure.
3. Turn on water supply and check for leaks.
Step 1
Package Contents
The box should contain the following:
Control Valve
Qty: 1
Swivel or Rigid Gooseneck Spout
Length determined by model
Qty: 1
Swivel spout includes one 2002 snap ring
and two 1600-5000 o-rings
10456
Lube
1000-8002
Slip Joint Kit
Slip Joints
Thread Sealant
Goes Here
Installation Instructions Continued
Step 2 - Swivel
Step 3 - Swivel
Apply O-Ring
Lube Here
Step 2 - Rigid
Step 3 - Rigid
Apply Thread
Sealant Here