American Standard Beale 4931300 User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M965685 Rev. 1.0 (4/16)
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
BEALE™
MANUAL PULL-DOWN
KITCHEN & BAR FAUCETS
INSTALLATION
INSTRUCTIONS
4931300
4931410
Flat Blade Screwdriver Adjustable Wrench Plumbers’ Putty or CaulkingPhillips Screwdriver
Certied to comply with ANSI A112.18.1M
B (OPTIONAL)
A
SPOUT BASE
SINK OR
MOUNTING
SURFACE
SPOUT BASE
3
7
9
8
2
10
12
5
3
6
7
9
4
4
8
1
12
13
5
6
11
14
CAUTION Turn off water at
main supply
(A) Installation less DECK ESCUTCHEON
• Make certain the SEAL (2) is properly seated in bottom recess of MOUNTING RING (10) and SEAL (12) in top recess of
MOUNTING RING (10). Insert supply HOSES (3), SPRAY HOSE (4) and SHANK (5) through mounting hole and seat SPOUT
BASE onto sink or mounting surface. Do not use putty.
• Insert HOSES (3) through RUBBER WASHER (6), BRASS WASHER (7), and threaded LOCKNUT (8).
• Assemble RUBBER WASHER (6), BRASS WASHER (7), and threaded LOCKNUT (8) onto SHANK (5) from underside
of sink or mounting surface. Hand tighten LOCKNUT (8).
• Use a screwdriver to tighten SCREWS (9) on LOCKNUT (8). Work your way around LOCKNUT (8), tightening the screws
slightly each time until all are snug to ensure even pressure.
(B) Installation with DECK ESCUTCHEON (optional)
• Make certain the SEAL (12) is properly seated in top recess of DECK ESCUTCHEON (1) and SEAL (13) is properly seated
in bottom recess of DECK ESCUTCHEON (1). Do not use putty.
• Screw in two THREAD RODS (14) onto bottom of DECK ESCUTCHEON (1).
• Insert SUPPLY HOSES (3), SPRAY HOSE (4) and SHANK (5) through hole of DECK
ESCUTCHEON (1), and mounting surface.
• Follow mounting instructions above
to secure faucet to mounting surface.
Thread the MOUNTING NUTS (11) to
secure DECK ESCUTCHEON.

- 2 -
2
M965685 Rev. 1.0 (4/16)
3CONNECT SPRAY HOSE AND INSTALL WEIGHTS
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLY HOSES (1, 2) directly to wall
supplies. Connection on tting supplies are 3/8"
compression. Connect left supply hose (Red Stripe) to Hot
wall supply. Connect right supply hose (Blue Stripe) to Cold
wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
*Faucet supplies are 35"long from faucet base.
• Note: If additional supply length is required, installer
must purchase additional parts separately.
• Important: If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
MAKE WATER SUPPLY CONNECTIONS
1
2
COLD
HOT
7
6
8
2
1
3
4
5
18"
• Push the SPRAY HOSE END (1) into the HOSE
CONNECTOR (2) and slide down the LOCKING
COLLAR (3) until it snaps into place.
• With HAND SPRAY (4) seated in SPOUT (5), install
WEIGHT (6) at labeled area onto HOSE (7), secure
with SCREW (8).
4
SPRAY OPERATION
• With FAUCET on, press TOGGLE BUTTON (4) on SPRAY (3) to switch
from stream to spray.
• Press and hold PAUSE BUTTON (5) to temporarily stop ow from SPRAY
(3). Release PAUSE BUTTON (5) to resume ow from SPRAY (3).
STREAM (AERATOR)
SPRAY
5
3
4
• Move HANDLE (1) into “off” position.
• Turn on water supplies and check connections for leaks.
• Operate HANDLE (2) up and down, left and right to ush
water lines thoroughly.
• Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS FOR LEAKS
CHECK
CONNECTIONS
FOR LEAKS

- 3 -
6
7
If Faucet Drips, Proceed As Follows:
• Turn VALVE to OFF position.
• Operate HANDLE several times from OFF to ON position. Do not apply excessive force.
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, rst turn off water supply then:
• Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
• Unthread ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).
• Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).
• Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
• Place SEALS (8) into CARTRIDGE PORTS (6a).
• Place CARTRIDGE (6) onto MANIFOLD (7) and tighten
MOUNTING SCREWS (5) alternately.
• Replace ESCUTCHEON CAP (4), HANDLE (3),
tighten HANDLE SCREW (2) and install
INDEX BUTTON (1).
DO: CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
SERVICE
CARE:
5
M965685 Rev. 1.0 (4/16)
1
2
4
5
6
86a 3
7
1
REMOVE
2
3
TEST INSTALLED FAUCET
• Turn ON water at main supply.
• With HANDLE (1) in “off” position, unthread SPRAY (3) from HOSE (2).
• Operate handle back to front, in COLD and HOT positions, to ush water
lines thoroughly.
• Replace SPRAY (3) onto HOSE (2).

- 4 -
M964454-YYY0A
ESCUTCHEON AND SEAL
(OPTIONAL)
M962146-0070A
MOUNTING KIT
M964395-0070A
WEIGHT
M964451-YYY0A
SPRAY WITH HOSE
(BAR)
M964450-YYY0A
SPRAY WITH HOSE
(PULL-DOWN)
M951483-0070A
CARTRIDGE
M918511-0070A
CARTRIDGE SCREWS
M907315-YYY0A
ESCUTCHEON CAP
M964453-YYY0A
HANDLE KIT
M922383-0070A
AERATOR KEY
(BAR)
M922372-0070A
AERATOR KEY
(PULL-DOWN)
M964452-YYY0A
MOUNTING RING
A911897-0070A
SEAL
M965685 Rev. 1.0 (4/16)
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 002
STAINLESS STEEL 075
MODEL NUMBER
4931300
4931410
BEALE™
MANUAL PULL-DOWN
KITCHEN & BAR FAUCETS
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200