Fisher-Price L5807 User manual

1
Basketball
Basketball
Basketball
Basketball
Basketball
Basketball
Model L5807
Model L5807Model L5807
www.fisher-price.com
®
Grow
Grow
-to
to
-Pro
Pro
Grow - to - Pro
Grow - to - Pro
Grow - to - Pro
Grow - to - Pro

2
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A.
©2006 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO L5807pr-0920
• Please keep this instruction sheet for future reference, as it contains
important information.
• Adult assembly is required.
• Tool needed for assembly: Phillips Screwdriver (not included).
• Water or sand is needed to fill the base (not included).
IMPORTANT! Backboard height should be adjusted only by an adult.
CAUTION
This product contains small parts in its
unassembled state.
Adult assembly is required.
CONSUMER INFORMATION
CONSUMER INFORMATION
CONSUMER INFORMATION
QUESTIONS?
Visit us on-line at www.service.fisher-price.com.
Call our Consumer Relations Department, toll-free at 1-800-432-5437,
9 AM - 7 PM EST Monday through Friday and 11 AM - 5 PM EST Saturday.
Hearing-impaired consumers using TTY/TDD equipment, please call
1-800-382-7470. Write to us at: Fisher-Price®Consumer Relations,
636 Girard Avenue, East Aurora, New York 14052.

3
4
5
6
Collar
Backboard
Ball
Rim
Lower Post
Upper Post
Plug
Base
Net Assembly
Note: Label not shown
Hint: Some parts were placed inside the lower post for shipping.
SHOWN ACTUAL SIZE
#6 x 5/8" (1.6 cm) Screw - 4
PARTS
PARTS
PARTS

4
11
• Place the loops at the top of the net into the grooves on the ring.
• Pull each loop through a ring tab, as shown.
Hole
Hole
Rectangular Tabs
Hole
Rim
Hole
Net Assembly
• Place the rim on a flat surface with the rectangular tabs facing up.
• Locate the four screw holes on the underside of the net assembly.
• Align the four screw holes on the underside of the net assembly with the
four holes in the rim.
• Place the net assembly onto the rim.
• While holding the ring assembly and rim together, turn them over.
• Insert four screws into the holes in the rim, making sure each hole in the
rim is still aligned with each screw hole in the net assembly.
• Partially tighten the screws with a Phillips screwdriver. Turn the rim
over to ensure that the net loops are still in the grooves and through the
ring tabs before completely tightening the screws. Do not over-tighten
the screws.
Rim
Groove Ring
Tab
Groove
Ring
Ring Tab
Side Edge
Side Edge
3
2
45
1
Proper label application will help to keep the label looking its best!
• Make sure the area where the label will be applied is clean and dry. Wipe
the backboard with a clean, soft, dry cloth to remove any dust or oils.
• For best results, avoid applying the label more than once.
• Peel the backing from one half of the label. Do not remove all of the backing!
• Align the side edge of label 1 (where backing is removed) with the side edge
of the label area on the backboard.
• Carefully apply the side edge of the label to the side edge of the label area
on the backboard.
• While rubbing the label in place, continue to peel the backing from the
other half of the label.
• Apply the remaining labels to the backboard. Labels 2-5are designed
to overlap.
• Dispose of the label backing properly.
ASSEMBLY
ASSEMBLY
ASSEMBLY
2
3
4

5
• Bend the “T” end of the plug and insert it into the hole in the base.
Note: After assembly is complete, fill the base with water or approximately
50 lbs. (22.7 kg) of sand (water and sand not included) to keep this product
stationary. Simply lift the plug, fill the base, and replace the plug.
Plug
“T” End
Base
• Position the base as shown.
• Position the upper post so that the straight end is down and the curved end
is up and facing away from the base.
Hint: For easier assembly, apply liquid soap or rub a candle or bar soap
around the bottom of the upper post (especially on the corners) and the inside
of the large square opening. If assembling inside, place a tarp under the base
to protect the floor surface.
• Insert the upper post into the large square opening in the base and, using a
circular motion, push it all the way down.
• Hook the rectangular tab on each side of the rim to the upper post,
as shown.
• Rotate the rim down until it snaps into place on the upper post. Push down
on the rim to be sure it is secure.
4
5
6
Large Square Opening
Base
Upper Post
Curved End
4
5
6
Rectangular Tab
Rim
Upper Post
ASSEMBLY
ASSEMBLY
ASSEMBLY
5
6
7
6
4
5
Backboard
Labels
Peg
Groove
Wall
Rim
Upper Post
• Lean the rim against a wall for support.
• Locate the pegs on each side of the rim and the grooves on the backboard.
• Position the backboard with the label side facing up.
• Place your foot on the base to hold it steady and slide the backboard onto
the upper post at an angle, as far as it will go.
Note: There should be no gap between the upper post and the backboard.
• Move the assembly away from the wall.
8

6
Note: The collar may already be factory assembled.
• Align the lever on the side of the collar with the opening in the top of the
lower post.
• Fit the collar onto the lower post, making sure the peg on each side of the
collar snaps into the hole on each side of the post.
PULL HERE
PRESS HERE
Top View
• Move to the side of the assembly.
• Place your foot on the base to hold it steady.
• Press down firmly on the lower backboard while rotating the backboard up.
• When properly assembled, the pegs on the upper post rest in the grooves
in the backboard, as shown.
Note: The height of the rim is three feet (1 m) as assembled.
6
4
5
Lower Post
Rib
Groove
Base
IMPORTANT! Assembly of the lower post to the base is a
permanent assembly.
• Align the rib on the bottom of the lower post with the groove in the
opening in the base.
Hint: For easier assembly, apply a small amount of liquid soap around the
bottom of the post. If assembling indoors, place a tarp under the base to
protect the floor surface.
• Insert the lower post into the opening and push down, using a circular
motion, until it snaps into place.
Collar
Lever
Opening
Lower
Post
Hole
Peg
ASSEMBLY
ASSEMBLY
ASSEMBLY
9Back View
Peg Peg
Grooves
10
11
• If the lever comes off, simply re-attach it.
• Insert the peg on one side of the lever into the hole in the collar.
• Snap the other peg in the lever into the other hole in the collar.
Assembly is now complete.
Please refer to assembly step 2 to fill the base with water or approximately
50 lbs. (22.7 kg) of sand (water and sand not included) to keep this
product stationary.
Holes
Peg
Peg
12

7
ADJUSTING THE RIM HEIGHT
ADJUSTING THE RIM HEIGHT
ADJUSTING THE RIM HEIGHT
1
5
4
6
Slots
Lever
Upper Post
Lower Post
• As assembled, the rim height is 3' (1 m).
• To raise the rim height to 4', 5', or 6' (1.2 m, 1.5 m or 1.8 m), place your
foot on the base and pull up on the backboard with both hands to remove
the upper post from the base. You may need to rock the upper post to
loosen it from the base.
IMPORTANT! Since this may require a lot of force, DO NOT stand with your
face or chest above the backboard.
• To lower the rim height: while holding the upper post, push the lever on
the lower post down. Lower the upper post and push the lever into the slot
at 4' or 5' (1.2 m or 1.5 m).
•To raise the rim height: simply lift the upper post and push the lever into
the slot at 5' or 6' (1.5 m or 1.8 m).
• Pull the lever on the lower post down.
• Insert the upper post into the lower post with the net positioned over the
wheels on the base.
• Push the lever into one of the slots on the side of the upper post at the
desired height.
4
5
6
Backboard
Base
Upper Post
5
4
6
Lever
Base
Slots
Upper Post
Lower Post
2
3

8
CARE
CARE
CARE
MAINTENANCE
MAINTENANCE
MAINTENANCE
• This toy includes an inflatable ball. If the ball becomes soft, inflate it with
a standard, manual air pump with a standard air needle.
• The ball will contain the correct amount of air when its circumference
measures about 21-22 inches (53-56 cm). Measure the circumference of
the ball with a tape measure or with a piece of string cut 21-22 inches
(53-56 cm) long. Do not over-inflate the ball.
• Periodically check all fasteners regularly to be sure they are tight. If the
fasteners are not tight, tighten them as necessary.
• Check plastic parts regularly and if broken or cracked, dispose of
them properly.
For countries outside the United States:
CANADA: Questions? 1-800-432-5437. Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2;
www.service.mattel.com.
GREAT BRITAIN: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303;
www.service.mattel.com/uk
AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
NEW ZEALAND: 16-18 William Pickering Drive, Albany 1331, Auckland.
ASIA: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.
• The frame and net may be wiped clean using a mild cleaning solution and
a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners.
Rinse clean with water to remove residue. Do not immerse this toy.
• To prolong the life of the net, store this toy indoors.
• Do not leave this toy outside in freezing weather. Water left inside the base
will freeze and possibly damage the base.
• We recommend indoor storage if this product will not be used for an
extended period of time.