Fit4Home PERFORM2 CTS803 User manual

1
EK-EQXH-NEJXPlease Keep For Future Reference
IMPORTANT - Please Read Instructions Fully Before Assembly Or Use
These instructions contain important information which will help you get the best
from your equipment and ensure safe and correct assembly, use and maintenance.
If you need help or have damaged or missing parts,
call the Customer Helpline: 0330 124 0718 (Opening hours: Mon-Fri 9:00am-3:00pm)
or Email: [e-mail]
PERFORM2 CTS803
USER MANUAL

2
CONTENTS
Safety Information
Exploded Diagram
Parts List
Assembly Instructions
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Operating the Computer
Maintenance
Declaration
03
04
05,06
07
07
07
08
08
08
09
09
10
11
12

3
IMPORTANT SAFETY INFORMATION
1. Before your starting to exercise, read the manual carefully and also always keep this
manual with you.
2. Before beginning any exercise program you should consult your doctor rst to
determine if you have any medical or physical conditions that could put your health
and safety at risk or prevent any damage. Your doctor’s advise is essential if you are
taking medication that aects your heart rate, blood pressure or cholesterol level.
3. Be aware of your body’s signals. Incorrect or excessive exercise can hurt your health.
If you feel dizziness, nausea, chest pain, back pain or other health symptoms stop the
workout at once and consult your doctor before continuing.
4. Do not operate any exercise equipment if it is not assembled well. Also you must
inspect your machine periodically to ensure your machine in good condition. It is your
responsibility to ensure that all users of the equipment are informed of all warnings
and precautions.
5. Keep children and pets away from the equipment. The equipment is designed for
adult use only. The equipment is not suitable for therapeutic use.
6. Before using the machine, please check the nuts and bolts are securely tightened.
7. Always use the equipment as mentioned. If any defective components which have
been found while assembling or checking the equipment, or you hear any unusual
noises from the equipment during use, stop immediately. Do not use the equipment
until the problem has been solved.
8. Wear appropriate workout clothing while exercising. Do not wear robes or other
clothing that could become caught in the machine. Running or aerobic shoes are also
required while using the machine.
9. Use the equipment on a at, clear surface. Do not use it near the water or outdoors.
10. Keep hands away from all moving parts. Always lift or move the equipment with care.
11. Maximum weight of user: 100kg.

4
EXPLODED DIAGRAM
NEEDS DIAGRAM IMAGE

5
PARTS LIST
No. Description Quantity No. Description Quantity
1 Main frame 1 46 Carriage bolt
M10X L56
4
2 Front bottom tube 1 47 Acorn nut φ3/8" 4
3 Back bottom tube 1 48L/R Nylon Nut 1/2"×
B8
2
4 Right coupler bar 1 49 Arc wash- 4
5 Left coupler bar 1 50 Computer 1
6R Right pedal tube 1 51 Spring wash-
erφ10.5×3×φ18
2
6L Left pedal tube 1 52 Washer
φ16×1×2.5×φ28
1
7R Right handle bar 1 53 Square end cap 2
7L Left handle bar 1 54 End cap S14 4
8R Right chain cover 1 55 Washer 1
8L Left chain cover 1 56 D shape washerφ
28×φ16.2×14×B5
”erφ28×φ16.2×1
4×B5”
2
9 End cap S16 4 57 Bolt M10×18 2
10 Screws ST4*19 2 58 bushing 2
11 Pedal 2 59 Nut M6 2
12 Handle bar shaft 1 60 Open-end wrench 1
13 End caps (φ2") 2 61 Bolt M10×L55×l25 2
14 Foam grips 2 62 Pedal hinge bolt 1
15 End caps (φ1") 8 63 Pedal hinge 1
16 Plastic bushing (φ1-
1/4")
4 64 Seat 1
17 Knob bolt 4 65 Washer D8 3
18 End caps (φ2") 2 66 Nylon nut M8 3
19 Plastic bushing
φ24×20×φ16.1
10 67 Saddle tube 1

6
20 Plastic bush-
ingφ14×12.5×φ10.1
4 68 Extension tube 1
21 Belt 1 69 Square bushing 1
22 Fan wheel axle 1 70 Handlebar line 2
23 Nut M10×1×B5 4 71 Solid wrench S13-
17-19
1
24 Chain wheel 1 72 Socket head
wrench S6
2
25 Nut M10×1×B10×φ20 2 73 Socket head
wrench S8
1
26 sensor 1 74 Spile 2
27 Crankshaft 1 75 Middle line 1
28 Plastic cap 2 76 Tube plug 2
29 Washer 1 77 Washer D8 2
30R Collar housing R 1 78 Hexagon bolt M8 2
30L Collar housing L 1 79 Handlebar post 1
31 Collar ball 2 80 Nylon nut M6 2
32 Collar housing 2 81 Wheel 2
33 Nut 1 82 Bolt M6*48 2
34 Chain 80Z 1 83 Bolt M5 4
35 Screw ST4.2*16 1 84 Handlebar grip 2
36 Flywheel 1 85 Knob 1
37 Computer line I 1
38 Chain cover screw
ST4.8×20
6
39 Chain cover screw
ST4.8×48
6
40 Pulse 2
41 Computer line II 2
42 Bolt M6×36 2
43 End cap S19 2
44 Bolt M10×45 4
45 Nylon nut M10 6

7
ASSEMBLY INSTRUCTIONS
STEP 1
FIG.1: Install the Front bottom
tube (2) and Back bottom tube (3)
to the Main frame (1) with Carriage
bolts (46), Arc washers (49) and
Acorn nuts φ3/8" (47).
STEP 2
FIG.2:
A: Insert the Handle bar shaft (12)
through the Coupler bar of left &
right (4, 5) and the Main frame (1)
at the same time, then x with D
shape washers (56), Washers (52),
Bolts (57) on both sides.
B: Insert the Pedal hinge bolt (62,
63) through the Pedal tubing (6L,
6R) to the Crankshafts (27L, 27R)
and x with Nylon nuts (48L, 48R),
Spring washers (51), nally cover
with plastic cap(9,43).
NEEDS DIAGRAM IMAGE
NEEDS DIAGRAM IMAGE

8
STEP 3
FIG.3: Attach the Pedals (11L, 11R)
to the Pedal tubes (6L, 6R) with
Bolts (44) and Nylon nuts (45).
STEP 5
Fix the Seat (64) on the Saddle
tube(67) with the Nylon nut(66)
and the Washer(65), then cover
the Extension tube(68).Insert
the saddle tube(67)into the main
fame(1),then tighten with the
knob(85).
STEP 4
Insert the Handle bar (7L,
7R) to the coupler bar (5, 4),
select a height setting that is
comfortable to the user, and
make sure both handle bars are
set at the same height. Lock
each handle bar in a place with
Knobs (17)and end cap(54) .
ASSEMBLY INSTRUCTIONS

9
STEP 6
Lock the spile(74)on the main
frame(1) with the knob bolt(17).
Install the handlebar post(79) on
the spile(74) using the washer(77)
and the bolt(78)
STEP 7
Connect the computer wire with
sensor wire,after that x the
computer(50) to the computer
bracket on the handlebar post(79)
with screw(83) and washer.
ASSEMBLY INSTRUCTIONS
NEEDS DIAGRAM IMAGE

10
OPERATING THE COMPUTER
SPECIFICATIONS:
TIME……………………………………………………………………00:00-99:59
SPEED(SPD)..……………………………………………0.0-99.9KM/H (ML/H)
DISTANCE………………………………………………….....0.00-9999KM (ML)
CALORIES…………………………………………………….......0.0-9999KCAL
※ODOMETER(ODO)…………………………..…………..…0.0-9999KM (ML)
※PULSE (PUL) …….....................................................................0※40~240BPM
KEY FUNCTIONS:
MODE: This key lets you to select and lock on to a particular function you want.
SET: Can to proceed the data establish for “TIME” “DISTANCE” “CALORIES”“PULSE”.
CLEAR(RESET): The key to reset the value to zero by pressing the key.
ON/OFF(START/STOP): The key to pause the signal input by pressing the key.
OPERATION PROCEDURES:
1. AUTO ON/OFF
• The system turns on when any key is pressed or when it sensor an input from the speed sensor.
• The system turns o automatically when the speed has no signal input or no key are pressed for
approximately 4 minutes.
2. RESET
The unit can be reset by either changing battery or pressing the MODE key for 3 seconds.
3. MODE
To choose the SCAN or LOCK if you do not want the scan mode, press the MODE key when the pointer on the
function you want which begins blinking.
FUNCTIONS:
1. TIME: Press the MODE key until pointer lock on to TIME. The total working time will be shown when starting
exercise.
2.SPEED:Press the MODE key until the pointer advance to SPEED. The current speed will be shown.
3.DISTANCE:Press the MODE key until the pointer advance to DISTANCE. The distance of each workout will be
displayed.
4.CALORIE: Press the MODE key until pointer lock on to CALORIE. The calorie burned will be displayed when starting
exercise.
5.ODOMETER(IF HAVE): Press the MODE key until the pointer advance to ODOMETER.The total accumulated
distance will be shown.
6.PULSE(IF HAVE): Press the MODE key until the pointer advance to PULSE .User’s current heart rate will be
displayed in beats per minute. Place the palms of your hands on both of the contact pads(or put ear-clip to ear),and
wait for 30 seconds for the most accurate reading.
7.SCAN: Automatically display changes every 4 seconds.
8.BATTERY:If improper display on monitor, please reinstall the batteries to have a good result
HOW TO INSTALL THE BATTERY:
1. Remove the battery cover at the rear of computer.
2. Place two “SIZE-AA” battery into the battery housing.
3. Insure battery is correctly positioned and battery spring is proper contact with battery.
4. Re-install the battery cover.
5. If the display is illegible or only partial segment appear, remove battery and wait 15
6. seconds before reinstalling.

11
MAINTENANCE
CLEANING
The elliptical trainer can be cleaned with a soft cloth and mild detergent. Do not use abrasives or
solvents on plastic parts. Please wipe your perspiration o the elliptical trainer
after each use. Be careful not get excessive moisture on the computer display panel as this
might cause an electrical hazard or electronics to fail.
Please keep the elliptical trainer, specially, the computer console, out of direct sunlight to
prevent screen damage.
Please inspect all assembly bolts and pedals on the machine for proper tightness every week.
STORAGE
Store the elliptical trainer in a clean and dry environment away from children.
TROUBLESHOOTING
PROBLEM SOLUTION
There is no display on the computer
console.
1. Remove the computer console and
verify the wire that comes from
the computer console is properly
connected to the wire that comes from
the main frame.
2. Check if the batteries are correctly
positioned and battery springs are in
proper contact with batteries.
3. The batteries in the computer console
may be dead. Change to new batteries.
The elliptical trainer makes a squeaking
noise when in use.
The bolts may be loose on the elliptical
trainer, please inspect the bolts and
tighten the loose bolts.

12
Declaration of Conformity
We, Importer
Fit4home Ltd
Unit A, Perseverance Mills, Olive Lane, Darwen BB3 3DQ United Kingdom
Declare that the product
TF-8.2DA Elliptical Trainer
Complies with the essential health and safety requirements of the
following directive:
Stationery training equipment EN ISO 20957-1:2013
EN ISO 20957-9:2016
Authorised Signatory and technical le holder
Signed for and behalf of:
Fit4home Ltd
Unit A
Perseverance Mills
Olive Lane
Darwen
BB3 3DQ
United Kingdom
Tassadaq Hussain

13