flair21 VERTICAL WRAP User manual

flair21.com | 800.845.0918 OVER
Your Vertical Wrap system has been custom made to your specifications. The appropriate mounting hardware
(either ceiling or wall clips) is included as per your order. PLEASE FOLLOW THESE INSTALLATION INSTRUCTIONS.
You will need a pencil, tape measure, drill, screw driver, pair of pliers, and the appropriate fasteners.
VERTICAL WRAP
installation instructions
Step 1
OUTSIDE MOUNT
Find the height for the top of the
bracket (as measured from the floor)
by adding the desired clearance to the
overall height of the treatment. When
installed, the recommended clearance
from the floor is 1⁄2”.
Place the first bracket directly over the corner of the
window with a maximum of 15” between brackets.
Adjust the length of the bracket so that the louvers
clear any obstructions.
Step 1
INSIDE / CEILING MOUNT
Mount the clip bracket directly into the
ceiling or head. If installing a valance, that
clip must also be installed at this time.
The center of the clip bracket is also the
center of the vane hook. Therefore, mount the
screw a minimum of 2 1⁄4” in front of the window
frame (or other obstruction) to allow clearance
for the vanes. The maximum distance between
clips should be 15”.
Step 2
INSTALL HEADRAIL
After mounting all brackets, snap
in the headrail as illustrated. To
remove the headrail, simply push
the release lip up with a screwdriver.
Step 3
ATTACH VANES
Push the vane into the top of the hook, then
pull straight down to ensure it locks into place.
Step 4
ATTACH TENSION DEVICE
Attach the child safety device to its mounting bracket. Pull down on the bracket to align the center of the
screw hole with the indicator line. Mark and pre-drill the screw holes. Pull down on the bracket and device,
align it with the drilled holes, and mount the bracket. Check to ensure the loop can move freely through
the device. Indicator Line
Outside Mount
Screw Hole
Inside Mount
Screw Hole
Step 5
TEST TRAVERSE
Alternately pull the cords to see that
the blind traverses smoothly in both
directions.
CAUTION: ONLY TRAVERSE THE
BLIND WITH THE VANES IN THE
OPEN POSITION!
Step 6
TEST ROTATION
Pull the beaded chain once in each
direction, to completely rotate the
vanes from open to closed. This will
automatically align all of the vanes.

Vertical Wrap Installation
flair21.com | 800.845.0918
CAUTION!
• PVC vanes should be stored on a flat, level surface until they are installed.
• Your Vertical Wrap fabric was carefully inspected for holes, snags, runs and other flaws prior to shipping. Please use extra caution
when installing the wrap onto the vertical system. flair21 will not be held responsible for damage to the fabric caused by
installation or rough handling of the fabric.
• The child-safety tension device must be properly and securely mounted with tension on the drive loop for the system to be fully operable.
PACKING LIST
1. Headrail with Bead Chain and Cord
2. Wall Brackets
3. Mounting Clips
4. Child-Safe Tension Device
5. PVC Vanes
6. Valance
7. Valance Returns
8. Valance Clips
9. Valance Return Connectors
3
1
4
2
5
78
6
9
Step 7
ATTACH SNAP TAPE
Slip the snapped portion of the snap
tape over the front of each vane, then
slide the snap tape around the other
side of the carrier and snap the tape at
the back of each vane.
Step 8
INSERT BOTTOM OF VANES
Carefully slide each vane in front of the tack
at the bottom of the wrap.
TIP:To prevent snagging the fabric, wrap
a plastic sandwich or grocery bag around
the vane while sliding it in front of the tack.
Ceiling or
Window Well
Valance
Valance Clip
Step 9
OUTSIDE MOUNT VALANCE
Snap the mounting clips
(that are attached to the
valance clips) onto the
top of the headrail. Attach
the valance to the valance
returns using the valance
return connectors, then snap
the completed valance onto
the valance clips.
FOR SHIRRED SLEEVE VALANCE: Shirr the sleeve onto the PVC valance. Attach the returns to the valance using the valance return
connectors. Shirr the sleeve over the returns and use the provided clips to secure the fabric. Connect the valance clips (over the fabric)
onto the valance, and connect the completed valance onto the headrail.
Step 9
INSIDE MOUNT VALANCE
Instal the mounting screw
through the headrail bracket
clip and valance clip as shown
(see Step 1). Attach the valance
to the returns using the valance
return connectors, then snap the
completed valance (with returns)
onto the valance clips. Make sure
the vanes do not hit the valance.