HunterDouglas Silhouette Halo Duolite Parts list manual

UltraGlide®
U
ltraGl
i
PowerView® Gen 3
Automation
Silhouette
®
Halo
™
Duolite
®
Window Shadings
PowerView
®
Gen 3 Automation and
UltraGlide
®
Operating Systems
Installation • Operation • Care

CONTENTS
Questions?
Call Hunter Douglas Consumer Support at [phone].
© 2022 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or
their respective owners.
GETTING STARTED.........................................................................1
Product Views ..............................................................................1
Tools and Fasteners Needed .......................................................2
INSTALLATION ................................................................................4
Installation Overview ..................................................................4
STEP 1: Mount the Installation Brackets ...................................4
Mount the Installation Brackets — Inside Mount ......................5
Mount the Installation Brackets — Outside Mount ...................7
Additional Clearance with Spacer Blocks ...................................8
STEP 2: Mount the Battery Wand (PowerView®Gen 3) ..............10
STEP 3: Install the Shading .........................................................12
STEP 4: Connect the Power Source (PowerView®Gen 3) ...........15
OPERATION......................................................................................21
Operate the Shading ...................................................................21
UltraGlide®Shadings ...................................................................22
PowerView®Gen 3 Automation ..................................................23
Operating the PowerView App and Gen 3 Remote .....................24
Resetting the Shading (If Necessary) ..........................................26
TROUBLESHOOTING ......................................................................27
CARE..................................................................................................35
Removing the Shading ................................................................35
Cleaning Procedures ....................................................................35
DECLARATIONS...............................................................................37
CHILD SAFETY.................................................................................38
WARRANTY .....................................................................................39

GETTING STARTED
1
Product Views
Battery Wand
W
and
Headrail
End Cap
Quartette
Headrail
Installation Brackets
Booster Clip
Brackets
Back/Dust Cover
(Optional)
UltraGlide
®
PowerView
®
Gen 3 Automation
External Booster
External Booster

2
GETTING STARTED
Thank you for purchasing Hunter Douglas Silhouette®Halo™Duolite® Window Shadings.
With proper installation, operation, and care, your new shadings will provide years of beauty
andperformance.
Please thoroughly review this instruction booklet before beginning the installation. If your
shading has a protective plastic cover on the fabric-covered headrail, keep the plastic in place
until the shading is installed.
IMPORTANT: An orange shipping clip is installed in the headrail for the UltraGlide®shading.
Please do not remove the clip until instructed to do so.
Tools and Fasteners Needed
■
1
⁄ 4 " hex and flat blade screwdrivers ■ Level (laser level is recommended)
■ Measuring tape and pencil ■ Pliers
■ Power drill,
3
⁄ 32 " drill bit,
and
1
⁄ 4 " hex driver
■ Scissors (heavy-duty)
■
1
⁄ 16 " Allen wrench
In addition, you will need fasteners designed to work with your specific mounting surface(s).
■ #6 Hex Head Screws (Provided). Two 1
1
⁄ 2 " screws are provided per installation bracket.
■ Longer #6 Hex Head Screws (Not Provided). If using spacer blocks, use #6 screws
long enough for a secure attachment.
■ Speed Nuts and Screws (Provided). Extension brackets come with screws and speed nuts.
■ Rechargeable Battery Wand Spacer Block Kit (Provided with Rechargeable Battery
Wand Option). Two spacer blocks and two #8 2½" screws are in the kit.
■ Outside Mount Battery Wand Spacer Block Kit. Available separately in ½" and ¼".
■ Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall.
Speed Nut
and Screw
(Provided with Each
Extension Bracket)
#6 x 1½"
Hex Head Screw
(Provided)
Longer #6 Hex Head Screw
for Use with Spacer Blocks
(Not Provided)
Outside Mount
Battery Wand
Spacer Block Kit
(Available in both
½" and ¼")
Rechargeable Battery Wand
Spacer Block Kit
(Provided with Rechargeable
Battery Wand)
1
∕ 2 "
1
∕ 2 "

GETTING STARTED
3
Importance of Limit Stops on Silhouette Window Shadings
Limit stops serve as the upper travel limit for the bottom rail, preventing it from rotating
around the fabric roll.

INSTALLATION
4
Installation Overview
To install your shading, you will need to perform the following four steps:
STEP 1: Mount the Installation Brackets
STEP 2: Mount the Battery Wand (PowerView Gen 3)
STEP 3: Install the Shading
STEP 4: Connect the Power Source (PowerView Gen 3)
Mounting Types and Window Terminology
If the installation brackets are mounted correctly, the rest of the installation process follows
easily. To prepare for this important first step, review the mounting types and basic window
terminology illustrated below.
■ Refer to the appropriate page below based on your order:
➤ Inside Mount — Page 4
➤ Outside Mount — Page 4
STEP 1: Mount the Installation Brackets
■ The number of installation brackets required
varies with shading width, as shown in the table.
Outside Mount
Shading mounts
outside window
opening.
Inside Mount
Shading fits within
window opening.
Collectively, the sill and
jambs are called the
“window casement.”
Molding
Head Jamb
Sill
Jamb Jamb
Width Brackets Required
14" – 48" 2
48
1
⁄ 8 " – 84" 3
Installation
Bracket

INSTALLATION
5
Mount the Installation Brackets — Inside Mount
Prepare the Installation Brackets
NOTE: Back cover bracket is not provided with
rechargeable battery wand.
■ If using the optional back cover:
NOTE: If you have a battery wand, do not
remove the top tab on the back cover bracket.
The top tab ensures that there is clearance for
the If you have a satellite battery pack or an 18V
DC Power Supply, remove the top tab on the
back cover bracket.
➤ Snap the back cover bracket into the metal
installation bracket.
■ If not using the optional back cover:
➤ If you have a battery wand, remove the
bottom tab from the back cover bracket.
➤ Snap the back cover bracket into the metal
installation bracket. This ensures adequate
space for the battery wand.
➤ If you have a satellite battery pack or an 18V
DC Power Supply, it is not necessary to use
the back cover bracket.
Mount the Installation Brackets
■ From the headrail end marks, mark 2" for bracket location on the control side and 7" on
non-control side.
CAUTION: Installation brackets must be installed 7" from the shading end cap on the
non-control side. Failure to place the non-control side bracket outside this area will
damage the shading when installed.
➤ If more than two installation brackets came with your order, space additional bracket(s)
between the two end brackets and mark their location. Mount into wood whenever
possible.
➤ For PowerView®Gen 3 shadings with battery wand, allow a minimum of 18" between
bracket centerlines for the battery wand/rechargeable battery wand.
Remove top tab if using a satellite
battery pack or an 18V DC Power Supply.
Back Cover Bracket
Remove bottom tab if using a
battery wand and no back cover.
Top Tab
Bottom Tab
Back Cover
Slots

INSTALLATION
6
NOTE: Before the headrail is installed, the bracket levers need to be fully to the left.
Once the headrail is properly in place, the levers automatically click to the right.
■ The depth required for mounting will vary depending on the power supply and mounting
type.
■ Center the installation brackets on
your marks and mark the location of
the screw holes.
➤ Allow sufficient rear clearance
when positioning the brackets.
NOTE: Rear clearance is the distance between the back of the installation bracket
and the glass or frame
➤ Add an extra
1
⁄ 4 " of rear clearance if the optional back cover is used.
IMPORTANT: The back cover is not available with the rechargeable battery wand.
■ Use a level to check that the mounting surface is level. Shim (not provided) the brackets,
if necessary.
■ Use a
3
⁄ 32 " drill bit to drill holes for the mounting screws.
CAUTION: Use drywall anchors when mounting into drywall.
18" Minimum for Battery Wand/
Rechargeable Battery Wand
Space Evenly 2" to 3"
7"
Jamb Jamb
Space Evenly
Operating System Type
Minimum Mounting Depth Fully Recessed Depth
Without
Back Cover
With
Back Cover
Without
Back Cover
With
Back Cover
UltraGlide®1"1
1
⁄ 4 "3
13
⁄ 16 "4
1
⁄ 16 "
PowerView®Gen 3
with Battery Wand 2" 2
1
⁄ 4 "4
9
⁄ 16 " 4
13
⁄ 16"
PowerView Gen 3 with
Rechargeable Battery Wand 2
1
⁄ 4 " — 4
13
⁄ 16 "—
Rear
Clearance
Nearest
Obstruction
Jamb
Operating System and Power Supply Rear Clearance
UltraGlide ¼"
PowerView Gen 3 with satellite battery ¼"
PowerView Gen 3 with battery wand ¾"
PowerView Gen 3 with rechargeable battery wand 1"

INSTALLATION
7
■ Attach the installation brackets using the screws provided.
NOTE: Do not overtighten the screws. Check to ensure
the lever can be moved easily side to side. If the lever is
not moving easily, loosen the screws in one-eighth turn
increments until it can be moved easily.
IMPORTANT: The front edges of the installation brackets
must be level and aligned to each other.
UltraGlide®Shading : Proceed to
“STEP 3: Install the Shading” on page 12.
PowerView® Gen 3 Shading: Proceed to
“STEP 2: Mount the Battery Wand (PowerView® Gen 3)” on page 10.
Mount the Installation Brackets — Outside Mount
■ Center the headrail over the window opening at the desired height. Use a pencil to lightly
mark each end of the headrail.
➤ Alternatively, measure the width of the headrail and use that width to mark the
headrail end points over the window opening.
■ From the headrail end marks, mark 2" for bracket location on the control side and 7" on
non-control side.
CAUTION: Installation brackets must be installed 7" from the shading end cap on the
non-control side. Failure to place the non-control side bracket outside this area will
damage the shading when installed.
➤ If more than two installation brackets came with your order, space additional bracket(s)
between the two end brackets and mark their location. Mount into wood whenever
possible.
➤ For PowerView Gen 3 shadings with battery wand, allow a minimum of 18" between
bracket centerlines for the battery wand/rechargeable battery wand.
Lever
18" Minimum for Battery Wand/
Rechargeable Battery Wand
Space Evenly 2" to 3"
7"
Jamb Jamb
Space Evenly

INSTALLATION
8
■ Center the installation brackets on your marks and mark the
location of the screw holes.
➤ A minimum 1" flat vertical height is required to mount the
installation brackets.
➤ Position the top of the installation brackets at the desired
height of the shading. The brackets must be level and aligned.
CAUTION: The rear of the blocks/brackets must be flush against a
flat mounting surface. Do not mount brackets on curved molding.
IMPORTANT: Additional clearance is required for PowerView®
Gen 3 shadings with a headrail-mounted battery wand or rechargeable battery wand. See
“Additional Clearance with Spacer Blocks” on page 8.
■ Use a
3
⁄ 32 " drill bit to drill holes for the mounting screws.
CAUTION: Use drywall anchors when mounting into drywall.
■ If no additional clearance is required, attach the installation
brackets directly to the mounting surface using the screws
provided.
IMPORTANT: The front edges of the installation brackets must
be level and aligned to each other.
WARNING: Failure to properly align the
brackets could result in the headrail releasing
from the brackets.
Additional Clearance with Spacer Blocks
NOTE: A minimum of
3
⁄ 4 " additional clearance is required for PowerView Gen 3 shadings with
a battery wand. A minimum of 1" additional clearance is required for PowerView Gen 3
shadings with a rechargeable battery wand.
■ If using
1
⁄ 4 " or
1
⁄ 2 " spacer blocks,
attach the spacer block(s) and
installation bracket to a flat vertical
mounting surface with #6 screws for
inside mount or #8 2½" screws for
rechargeable battery wand outside
mount to ensure a secure installation.
IMPORTANT: The solid side of the
spacer blocks must face toward the mounting surface.
Spacer
Blocks
Longer
Screws
1
1
⁄ 2 " Maximum
Added Clearance
1
∕ 2 "
1
∕ 4 "
Battery Wand
1
∕ 2 "
1
∕
2
"
Rechargeable
Battery Wand