Flash Furniture YK-1077-BEIGE-K-GG User manual

Thank you for your purchase !
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
lnjury may result from tipping furniture. You must install the Tipping Restraint Hardware with the unit to prevent
the unit from tipping and causing any accidental injury , instability, death or damage. The tipping restraint is
intended only as a safety measure, it is not a substitute for proper adult supervision.
This tipping restraint is not an earthquake restraint. lf you wish to add the extra security of earthquake restraints,
they must be purchased and installed separately.
Serious or fatal crushing injuries can occur fromfurniture tipping over. To prevent furniture from tipping over
it must be permanently fixed to the wall. Fixing devices for the wall are not included since different wall
materials require different types of fixing devices. Use fixing devices suitable for the walls in your
home
Failure to detach this restraint before moving furniture may result in injury or damage.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
..................................................................................
Customer Service Email: [e-mail] I Phone: [phone]
UPHOLSTERED
PLATFORM BED
<.%(,*(.**<.*<.**

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of
longlasting consumer relationships. We strive toward excellence in all we do and
want you to be completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email
address or phone number shown below to assist you with any product
questions or issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any issues
you may have.
Customer Seryice Email: [email protected]
Customer Service Phone: [phone]
Our Warrantv Statement
This warranty covers manufacturing defects associated with your new product. The product is
warranted from the original purchase date and to the original purchaser for normal usage,
according to the below-referenced specifications and limitations.
Non-moving metal parts are warranted for 5 years,
Component parts including pneumatic cylinder, control mechanism, base and casters
are warranted for 2 years.
All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and welght limits specified for the
product. ln the absence of product-specific restrictions and weight limits, normal usage means
use for no more than forty hours per week by persons weighing 250 lbs. or less. Coverage
terminates if the product is sold or otherwise transferred. Repairs made by parties otherthan
Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any other
event beyond the control of Belnick; (2)tearing, scratching, scuffing, or blemishing of leather or
fabric; (3) cosmetic damage that may result from normal usage; {4) damage attributable to use
by persons exceeding specified weight limits or commercial use exceeding forty hours per week;
or (5) rust or other damage caused by exposure to moisture. The user assumes all risk of injury
resulting from use of this product. Liability for incidental or consequential damage is excluded.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.

pcs
Part 9 : Footboard
Part 10: Headboard Wing
Part
Part 1:  & Right Side Rails
Part 2: Headboard
Part 3:
Part 4: Headboard Legs
Part 5:  & Right Side Legs
Part 6: Center Legs
Part 7: Center Rail
Part 8: Support Slats
4pcs
4
Footboard Legs
2pcs
1pc
2pcs
2pcs
8pcs
2pcs
1pc
2pcs

F
E
Ha
rdware
M8 x 35mm Screws
Part A 10pcs
M8 x 1mm Large Lock Washer
Part B 10pcs
M8 x 1mm Large Flat Washer
Part C 10pcs
M8 x 20mm Screws
Part E 8pcs
M6 x 45 mm Screws
Part F 4pcs
M6 x 50mm Screws
Part G
8pcs
M6 x 25mm Screws
Part H 8pcs
M30
Self Tapping Screw
Part I8pcs
M6 x 1mm
Small Lock Washer
Part J 8 pcs
M6 x 1mm Small Flat
Washer
Part K 8pcs
M4 x 95mm
Small Allen Wrench
Part L 1pc
M5 x 95mm
Large Allen Wrench
Part M 1pc
M6 x 23mm Adjustable
Height Glides
Part D 10 pcs
M6 x 70 mm Bolt
Part N 2pcs
NOTE: Phillips Screwdriver Required (Not Included)

Step 3 : Attach (2)
M6x23mm Adustable
Height Glides (Part D) to
Headboard Legs (Part 4).
10
2
M5
A
B
C
S:WP
P
SP
WP
WP
WP
Step 2 : 
PP
SP
W
P
WP
WP
10
2
10
24
A
B
C
4
F
H
J
K
5
Side Legs
Siderails
D
4
M8x35mm Screw
M8x1mm Large Flat Washer
M8x1mm Large Lock Washer
Large Allen Wrench
NOTE: Unzip liner to access screw holes.
Headboard Wings
Headboard
Headboard Legs
Adjustable Height Glides

Step 8 : ftRSR
PP
SP
WP
Step 9 : Attach (4) M6x23mm
Adustable Height Glides (Part D)
to bo omof the Headboard
Wings (Part 10).
Step 7 : Attach (2) M6x23mm
Adustable Height Glides (Part D)
to Side Legs (Part 5).
Step 4 : Attach (2) M6x23mm
Adustable Height Glides (Part D)
to Footboard Legs (Part 3).
K
J
H
M4
Step 10 : Attach Left and Right Side
Rails to Headboard Wings using (4)
M6x50mm Screws (Part F). Tighten
using M4 Small Allen Wrench (Part L).
Step 6 : SP
RSRP
SP
WP
W
PS
WP
M4
F
M5
E

M4


D

Footboard legs

D
5
5
D
Step 5: Attach
Footboard Legs
(Part 3) to Footboard
(Part 9) using (2)
M6x70mm Bolts
(Part N). Tighten
using M4 Small Allen
Wrench (Part L).
Side
Leg
Footboard
Footboard Legs
M6x70mm Bolt
Small Allen
Wrench
M6x25mm Screw
M6x1mm Large Lock Washer
M6x1mm Large Flat Washer
Small Allen
Wrench
Height Adjustable Glides
M8x20mm
Screw
M6x50mm
Screw
Large
Allen Wrench
Small Allen Wrench

H
J
K
6
Center Legs
8
Support Slat
7
Center Rail
G
G
7Center Rail
I
Step 11 : Insert (8) M6x50mm Screws (Part G) through the Support Slats (Part 8) and the Center Rails
(Part 7) and attach to the Center Legs (Part 6). Tighten using M4 Small Allen Wrench (Part L).
M6x50mm Screw
M4 Small Allen
Wrench

Step 12 : 2PRRP-
PPvN
I