Flash Furniture LF-215 User manual

Thank you for your purchase!
CCuussttoommeerr SSeerrvviiccee Emmaaiill:: CCuussttoommeerrEExxppeerriieennccee@@bbeellnniicckk..ccoomm || Phhoonnee:: 886666--555522--22881100
LF-215-SILVER-GG/LF-215-DEEPBLUE-GG/LF-215-BLK-GG/LF-215-APPLEGREEN-GG/LF-215-WINERED-GG/LF-215-YELLOW-GG/LF-215-PINK-GG/LF-215-VIOLET-GG/LF-215-RED-GG
LF-215-GREEN-GG/LF-215-BRIGHTBLUE-GG/LF-215-ORANGEYELLOW-GG/LF-215-WHITE-GG/LF-215-SPICYLIME-GG/LF-215-NAUTICALBLUE-GG/LF-215-CHERRYTOMATO-GG
HEIGHT ADJUSTABLE
DRAFTING STOOL WITH
TRACTOR SEAT
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/LF-215-SPICYLIME-GG.pdf

PARTS
STEP 1
STEP 2
A
B
C
D
E
1
1
1
1
1
F
G
H
I
1
1
5
1
F
H
G
F
5 STAR BASE
SEAT BACK
ATTACHMENT
FRAME
FOOT REST
ALLEN WRENCH
HEIGHT ADJUSTMENT MECHANISM
TRACTOR SEAT
BACK REST
COLUMN
STEP 1: Lay the Tractor Seat face down on a soft clean surface with
the interior curved edge toward you. Attach the Height Adjustment
Mechanism (Part F) to the Tractor Seat using (2) Dome Head Screws
(Part H). Ensure mechanism handle is facing right. Tighten with the
Allen Wrench (Part I)
Interior Curved Edge
Height Adjustment Mechanism
Dome Head Screw
Note: Ensure pneumatic handle is
facing right
STEP 2: Push Seat Back (Part G) onto posts of
Seat Back Attachment Frame (Part F).
Note: Ensure curve of backrest is facing
inwards toward the seat attachment
bracket.
Seat Attachment Bracket
Ensure inner curve is facing Seat
Bracket Attachment
Back Rest
Seat Back Attachment Frame

STEP 3
STEP 4
H
D
E
F
C
E
STEP 3: Place the Seat Back Attachment Frame (Part F)
on the underside of the Tractor Seat (Part E) on top of the
holes in the Height Adjustment Mechanism. Attach the
Seat Attachment Bracket using (3) Dome Head Screws
(Part H). Tighten with the Allen Wrench (Part I)
Dome Head Screw
Height Adjustment Mechanism
Tractor Seat
Seat Back Attachment
Frame
STEP 4: Insert larger end of the Column (Part C) into the 5
Star Base (Part A). Place the assembled seat onto the
Column and push down to attach.
Tractor Seat
Column
5 Star Base
Turn preassembled floor glides
counter-clockwise to adjust