Flash Furniture NAN-JN-2824S-GG User manual

Thank you for your purchase!
NAN-JN-2824S-GG / NAN-JN-2824S-BK-GG / NAN-JN-2824S-WH-WH-GG
Glass Top Computer Desk
with Pullout Keyboard
Customer Service Email: [email protected] | Phone: [phone]
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/NAN-JN-2824S-BK-GG.pdf

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of long-
lasting consumer relationships. We strive toward excellence in all we do and
want you to be completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email
address or phone number shown below to assist you with any product
questions or issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any
issues you may have.
Customer Service Email: [email protected]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product
is warranted from the original purchase date and to the original purchaser for normal
usage, according to the below-referenced specifications and limitations.
Non-moving metal parts are warranted for 5 years.
Component parts including pneumatic cylinder, control mechanism, base and casters
are warranted for 2 years.
All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified for
the product. In the absence of product-specific restrictions and weight limits, normal usage
means use for no more than forty hours per week by persons weighing 250 lbs. or less.
Coverage terminates if the product is sold or otherwise transferred. Repairs made by
parties other than Belnick also void this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any
other event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of
leather or fabric; (3) cosmetic damage that may result from normal usage; (4) damage
attributable to use by persons exceeding specified weight limits or commercial use
exceeding forty hours per week; or (5) rust or other damage caused by exposure to
moisture. The user assumes all risk of injury resulting from use of this product. Liability for
incidental or consequential damage is excluded. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.

Ix2
I
I
STEP 1: Cross the Left Leg (Part B) and Right Leg (Part C) and insert Bolt & Cap
Assembly (Part 6). Attach Lower Leg Braces (Part D) to bottom of legs using (4)
M6x12 bolts (Part 3). Set the Upper Leg Braces (Part A) on top of crossed legs (do not
attach).
NOTE: Be sure back legs are aligned by looking for small hole near
the bottom
STEP 2A: Attach Upper Leg Braces (Part A) to Front Bar (Part F) and Back Bar
(Part E) with dimpled holes facing down using (4) M6x55 Bolts (Part 1). Attach
Keyboard Arms (Part I Left & I Right) to Front and Back Bars using (4) M6x35 Bolts
(Part 2).
Attach Keyboard Glides (Parts 8 Left and 8 Right) to the Keyboard
Arms (Parts I Left and I Right) using dome head screw (Part 5)
STEP 2B: Attach Lower Brace (Part G) to back legs
using (2) M6x55 Bolts (Part 1). Attach Back Frame
Braces (Part H) to Lower Bar (Part G) and Back Bar
(Part E) using (4) M6x12 Bolts (Part 3).
STEP 3: Attach Keyboard Tray (Part K) to
Keyboard Arms (Parts I Left & I Right)
USING (4) M4X14 Screws (Part 4).
STEP 4: Place Glass Desk Top (Part J) on top of
front and back bars E & F. From the bottom of bars
E & F (dimpled holes) screw (4) M6x21 Bolt s(Part 7)
into the silver disks.
Phillips
Screwdriver
Left Leg
Right Leg
Upper Leg Braces
Lower Leg Braces
Bolt and Cap Assembly
M4x14 Screw
Left Glide
Left Keyboard Arm
Right Keyboard Arm
Right Glide
M4x14 Screw
Lower Brace
Keyboard Arm Keyboard Arm
Back Frame Braces
Glass Desk Top
Keyboard Tray
Front Bar
Back Bar