Flash Furniture NAN-JN-2824SL-COMBO-GG User manual

Thank you for your purchase!
L-Shape Computer Desk
with Pullout Keyboard
Customer Service Email: [email protected] | Phone: [phone]
NAN-JN-2824SL-COMBO-GG / NAN-JN-2824SL-COMBO-BK-GG
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/NAN-JN-2824SL-COMBO-GG.pdf

Cross the metal legs (Parts B & C)
and insert bolt (Part 7). Attach metal
bars (Part D) to bottom of legs with
bolt (Part 4)
Step 2A: Seat metal cap
(Part A) on the top of left
leg and attach to Front
and Back Bars with
dimpled holes facing
down (Parts E & F) .
Secure with bolt
(Part 2). Add corner
connector (Part P) to
right side using bolts (Part
1) inserted into metal leg
caps (Part A) and into
Back and Front support
bars (Parts E & F) Step 2B: Attach Lower Bar (Part I) to back
legs with Bolt (Part 2). Attach Back Frame
Braces (Part J) to Lower Bar (Part I) and
Back Bar (Part E) with bolts (Part 4)
Step 3B - Seat metal caps
(Part A) on the tops of
legs and attach to Front
and Back Bars with
dimpled holes facing
down (Parts G & H) .
Secure with bolt (Part 2).
Attach Lower Bar (Part I)
to back legs with Bolt
(Part 2). Attach Back
Frame Braces (Part J) to
Lower Bar (Part I) and
Back Bar (Part G) with
bolts (Part 4)
Step 3C - After assembling right side desk - Add corner
connector desk to right side desk using bolts (Part 1) inserted into
metal leg caps (Part A) and into Back and Front support bars
(Parts G & H)
Step 2C
Attach Keyboard Arms
(Part K Left & L Right) to
Front and Back Bars
(Part E & Part F) with
bolt (Part 8). Attach
Keyboard Glides (Parts 9
Left and 9 Right) to the
Keyboard Arms (Parts K
Left and L Right) using
dome head screws(Part 8)
Step 3A: Attach
keyboard tray (Part O)
to glides (Part 9) using
flat head screws (Part 6)
Place left and right desk glass
(Parts M) on top of front and
back bars E & F and G & H.
Place corner glass (Part N)
onto corner frame (Part P).
From the bottom of bars E &
F and G & H (dimpled holes)
screw bolt (Part 5) into the
silver disks. From the bottom
of part P screw 3 bolts (Part
11) into outer perimeter holes.
From the bottom of part P
screw bolt (Part 10) into inner
hole