Fleetminder FM-MT4G User manual

1
Motorcycle/Vehicle
Tracker
GPS+GSM/GPRS/LTE+SMS
User Manual
MODEL: FM-MT4G

2
CONTENTS
Ⅰ.Product Features.......................5
Ⅱ.Components and Accessories...7
Ⅲ.SIM card Installation..................9
Ⅳ.Device Installation ...................10
4.1 Install device........................ 10
4.2 device wiring definition....... 12
4.3 Relay wiring......................... 14
Ⅴ.Power ..................................... 15
5.1 Power on.............................. 15
5.2 LED Indicators..................... 15
5.3 Power off ............................. 16
Ⅵ.Inquiry/Monitoring/Cut Fuel.... 16
6.1 Inquiry by service platform.. 16
6.2 Inquiry by SMS.................... 17
6.3 Cut Fuel /Restore................. 17
Ⅶ.Device Alarm ......................... 17
7.1 Temperature Alarm.............. 17

3
7.2 VibrationAlarm................... 18
7.3 Collision / fallingAlarm ...... 18
7.4 SpeedAlarm......................... 18
7.5 Shift Alarm........................... 19
7.6 Geo-fence Alarm.................. 19
7.7 Power disconnectAlarm...... 19
7.8 Low battery Alarm............... 19
Ⅷ.Device Setting ........................ 20
Ⅸ.Trouble shooting......................20
9.1 Cannot connect platform...... 20
9.2 Offline status........................ 20
9.3 No positioned....................... 21
9.4 Position drift ........................ 22
9.5 Commands receiving
abnormally................................. 22
Ⅹ.Warranty Terms ..................... 23

4
Please read this manual carefully to install and
operate device properly.This user manual is
for reference only.
With FM-MT4G GPS Vehicle Tracker, you can
monitor your vehicle by GPS satellite
positioning system, 4G communication and
Internet, areal-time remote location and
monitoring and control of vehicles can be
achieved through the Fleetminder service
platform.

5
Ⅰ.Product Features
■ Supports GSM/LTE, include 19 bands,
universal in the world.
■ Super Wide Input Voltage：7-72V DC.
■ GPS precise positioning, Support A-GPS,
uploaded by LTE/GPRS regularly, real-time
tracking and history track playback.
■ ACC status detection
■ Support Temperature senor, SOS button,
External battery(Choose one of the three)
■ GPI/O port ,can be extended to Serial
port(Customization).
■ Built-in battery, Power disconnect alarm &
Low battery alarm.
■ Built-in G-sensor ,Vibration, collisionand
falling alarm.
■ GEO-fence alarm, speed &shift alarm.
■ Relay to cut engine, Auto cut engine when
over speed and recover when normal speed.
■ Support OTA upgrade
■ Water proof level IP65

6
Basic Specifications
Voltage
12/ 24/ 36/ 48/ 60/ 72 VDC
Work Current
GPRS(245-265mA); LTE(260mA)
Standby Current
IDLE(2mA@12V)
GPS Accuracy
5-15m
LBS Accuracy
>100m
GPS Band
1575MHz
GSM Band
850/900/1800/1900MHz
LTE Band
Global
bands(1,2,3,4,5,8,12,13,17,18,1
9,20,25,26,28 and 39)
Temperature-Sensor
Accuracy ± 0.5℃
Temperature-Sensor
Arrange -30℃~80℃
Working Temperature
Arrange -20℃~75℃
Hot/warm/cold Start
<3s，<15s，<60s
Battery Capacity
140mAh
Dimensions (mm)
89(L)X 37(W) X12(H)
Work Humidity
20%～80%RH
Net Weight
32g

7
Ⅱ.Components and Accessories
■ Components
-Top Front-
(Towards sky)
-Bottom -

8
■ Accessories
Power Cable(Default) Relay(Optional)
Temperature Sensor(Optional)
SOS(Optional) External Battery(Optional)
Relay for remotely cut engine, Temperature sensor
used for monitoring temperature, SOS button used
for help, External battery used for power supply,
(Temperature senor, SOS button, External battery
can be only chose one of the three).

9
Ⅲ.SIM Card Installation
Open the packing case, check if device is OK
and accessories are intact.
You need asuitable SIM card for using
device, contact your dealer if any question.
Open SIM Card cover
Insert SIM Card

10
Press cover and close
Note:
●Please cut off the power before installing or
uninstalling SIM card.
●SIM card should have GPRS/LTE function, check
network through operator.
●SIM card should have Caller Identification
function for telephone querying.
●If you enable the PIN code of the SIM card,
please use your mobile phone to disable the PIN
code.
●Please make sure SIM card has sufficient credit
balance.
Ⅳ.Device Installation
4.1 Install device
4.1.1 Please make sure your device is installed
by professional installer

11
Please make sure to install device with this side
upward, and use wide strong double-sided
adhesive tape to fix it.
4.1.2 Installation Notice
●Hide device properly inside the vehicle body in
order to avoid damages.
●Keep device away from RF emission sources
such as backing radar, vehicle alarm and other
vehicle mounted communication devices.
●Suggest to use wide strong double-sided
adhesive tape to fix it, or use cable ties and other
liable methods to fix it.
●Device Built-inGSM/LTE antenna and GPS
antenna, please ensure that signal receiving side is
facing up (towards the sky) when doing installation,
without any metal material covered on the top. It
may weaken signal and will not work properly.

12
4.2 Device wiring definition
Total schematic wiring device
4.2.1 Power cables and interface
The standard input voltage of device is 7V-72VDC,
so please use the original power cables, the red
cable is positive and the black cable is negative;
Please ground negative pole separately or ground it
to ground connection, not to any other ground.
Connect the ACC cable (orange cable) to ACC
switch of the vehicle, the data logs will show

13
ignition status of vehicle; the ACC cable can also be
connected directly to the positive pole of the vehicle
power, then the data logs will show that the vehicle
is always on (this is not recommended).
Connect the 4# cable (yellow cable) to the 85
device (with small yellow cable) of the relay. Use
cable ties to fix the relay to waterproof place, or
use plastic bags cover the relay.
Connect Temperature sensor with PIN7 &PIN8.

14
4.3 Relay wiring
Relay wiring diagram shows how to wire the relay to
control the fuel pump:
4.3.1 Connect the 86 port to the positive pole of the
vehicle power (+12V/+24V), connect the 85 port to
the 4# cable of device.
4.3.2 Cut off the positive pole of the fuel pump, next
serial connect the positive pole to the 87a port of
the relay, and connect another pole to 30 port,
showing as in the figure.
Bottom of the relay Wiring Diagram

15
Ⅴ.Power On /Off
5.1 Power on
Power on: insert avalid SIM card and wire all the
cables, device will power on.
5.2 LED Indicators
The red LED flickers fast when device is searching
for GSM/LTE network, it flickers intermittently when
device has registered the GSM/LTE network
successfully.
The blue LED flickers fast when device is searching
for the GPS satellite signal, it flickers intermittently
when device has searched the satellites and can be
positioned.
Red LED /GSM/LTE
Blue LED /GPS
Notice: Be sure the voltage of the vehicle power
should match up to the working voltage of relay, or
relay will be damaged.

16
1. Red LED(indicates GSM/LTE workingstate)
Fast blinking
Searching for
GSM/LTE network
Slow blinking
GSM/LTE connected
2. Blue LED(indicates GPS signal state)
Fast blinking
Searching GPS
Satellites
Slow blinking
GPS connected
5.3 Power off
Disconnect the external power and remove SIM
card, after awhile device will shut down.
Ⅵ.Inquiry/Monitoring/Cut Oil
6.1 Inquiry by service platform
6.1.1 Web Browser platform
Login the service platform and enter your ID and
password to check the position of device.
https://tracking.fleetminder.com.au
6.2.2 Smart phone applications
You can use asmart phone to check device’s
position. To download the app, search for
"Fleetminder Fleet Management" in the Google
Playstore or Apple Appstore.

17
Note: You need to set Temperature range value &
time.
6.2 Inquiry by SMS
You can write apositioning SMS sending to device
to inquiry position, device will reply position SMS or
map link. The SMS commands please refer to the
Operation Commands
6.3 Cut Engine/Restore
6.3.1 Cut off fuel circuits
Server(GPRS/LTE) or Manager number (SMS) can
send cut-fuel-circuit commands to device when
needed. Engine can not start.
For safety, fuel of vehicle can be cut off only if
device has been positioned by GPS and speed of
vehicle is less than 20KM/h or vehicle is static.
6.3.2 Recover fuel circuits
Server(GPRS/LTE) or Manager number (SMS) can
send recover-fuel-circuit commands to device when
needed, device will recover fuel circuits of vehicle.
Ⅶ.Device Alarm
7.1 Temperature Alarm
Conditions: When Temperature exceed set range

18
Conditions: When the Vehicle Vibration occurs.
Note: You need to set vibration sensitivity and time,
there is an alarm switch.
Or SOSAlarm
Conditions: When SOS button is long pressed for 3
seconds.
Note: SOS button must be installed (optional
accessory), and SOS administrator number must be
set. When the SOS alarm occurs, terminal will dial
the set SOS administrator number 3times until
getsthrough.
Note: When above alarm occurs, device will send
alarm to service platform, meanwhile send aSMS
message to administrator number if this number
was set.
7.2 Vibration Alarm
7.3 Collision / falling Alarm
Conditions: When Vehicle Collision or falling
occurs.
7.4 Speed Alarm/Cut enginewhen
over speed
Alarm Conditions: When vehicle speed over and
below the setting speed.
Cut engine Conditions: Cut engine when over
setting speed (Restore engine after returning

19
Note: Alarm parameters must be set before work in
7.1, 7.2, 7.4,7.5&7.6, Please refer to the
<Operation Commands>
setting speed)
Note: You need to set the low speed limit and the
high speed, and an over-speed setting to cut engine
7.5 Shift Alarm
Conditions: When vehicle occursasetting shift in
the Flameout status.
Note: Only valid in flameout state and vehicle
occursasetting shift distance.
7.6 Geo-fenceAlarm
Conditions: When the vehicle entry /exit /
across the Geo-fence.
Note: You need to set the conditions of crossing
fence, fence types and so on.
7.7 Power Disconnect Alarm
Conditions: When the device is disconnected
from external power.
7.8 Low Battery Alarm
Conditions: When the device is disconnected
from external power and built-inbattery power
falls below acertain value .

20
Ⅷ.Device Setting
Please refer to <Operation Commands>
Ⅸ.Trouble shooting
9.1 Cannot connect platform
Device cannot connect to the Fleetminder server
when installed at the first time. Please check device:
1) If power cables are wired correctly? Pay
attention to not connect them to controlling cables of
vehicle.
2) If SIM card is installed correctly? Please refer to
the installation instructions.
3) Check the status of LED indicators. If device is
OK, red LED and blue LED will intermittently flick.
4) Inquiry parameters of device via commands and
check replied parameters.
9.2 Offline status
First check if LED indicators are OK, if not,
Note: When above alarm occurs, device will send
alarm to service platform, meanwhile send aSMS
message to the administrator number if the number
is set.