Flexispot PS03 User manual

PAPER SHREDDER
PS03
Website: www.flexispot.com
Tel: [phone]
ADDRESS: 6475 Las Positas Rd. Livermore, CA 94551
USER MANUAL
SPECIFICATIONS
Model no: PS03
Input: 120V, 60Hz, 3.2A
Shred Capacity: 12 sheets (A4 70g paper)
1 PC Credit card / CD
Net weight: 12.3 lbs
Entry Width: 8.7 in
Cutting Style: Cross cut
Machine size: 14.17Lx9.6Bx15.74H (in)
NAMES OF COMPONETS
1. 3-Position slide switch for AUTO, OFF and REVERSE
2. Power indicator
3. Paper intake
4. Transparent window
5. Handle
6. Drawable waste bin
6
4
5
12
3
OPERATING ELEMENTS
The sliding switch (AUTO/OFF/REV CD Card) on the machine has the following functions.
AUTO position: the machine is ready for operation, shredding starts as soon as paper is inserted in the
paper entry.
OFF position: the machine is out of working.
REV(CD/Card) position: it can strip cut for CD/credit card when the switch is on this position, and it can
also set back paper.
INSTAL GUIDE
1. Put the machine on flat table.
2. Insert power plug into the corresponding electric socket and make sure that working voltage comply
with supplying voltage.

SAFETY OPERATION GUIDEOPERATION GUIDE AND REMARKS
1. Set the slide switch to “AUTO” position, at the same time, the machine is on standby; put the shredding
paper, vertically into the entry, there after, it starts up automatically and does shredding; it returns to
standby automatically after finishing.
2. When jam caused by inserting too much paper, or want to withdraw the paper immediately at the normal
shredding, please set the slide switch to”REV”, at the same time, the machine does the reverse rotation
and return the paper that has not been shredded; then put the switch to “OFF”.
3. Set the switch to “REV” position, at the same time, the machine is ready for cutting CD and credit card,
put the CD and credit card, vertically into the entry, then set the slide switch to “OFF” position when finish
cutting.
4. To ensure your machine has a long use life and exerts good shredding function, please refer notice the
maximum number of shred paper, and shred one piece of CD or credit card at one time. To exert its power
at the most, please notice it as follows: work continuously for 5 minutes; rest for 40 minutes, that is one
cycle. It can not work continuously more than 3 cycles.
5. If the machine works continuously or spasmodically for a long time, it may pause because the inside
temperature increases continuously. After resting for a period of time, it can work again.
6. Please do not put clips, adhesive paper, adhesive tapes or cloth into the paper entry in order to avoid
damaging the blades or lowering the shredding performance.
7. If you want to clean the wastebasket or the machine, or the machine is not used for a long time, please
cut off the electric power and unplug.
ABNORMITY AND COUTERMEASURE IN USE
Index
1
2
3
4
Abnormities Cause Countermeasure
The paper is jammed, and
the machine stops working.
Don’t work after inserting
paper, or stop running when
paper is being inserted.
The paper is too thin, too
soft, humid, or too crinkly to
activate automatic inductive
device.
1. The number of the
inserted paper is larger than
the limitation.
2. Locked rotor makes the
motor overheated and then
temperature protection set
takes action.
1. Fold the paper and then
insert it.
2. Set the slide switch to
“REV”.
1. Set the slide switch to
“REV” and withdraw the
shredding paper.
2. Unplug the plug and let
the machine stop for a while.
1. Before use, please read introduction manual carefully;
2. the socket-outlet shall be installed near the equipment and shall be easily accessible.
3. Keep ties, jewelry, hair, etc. away from the machine to insure personal safety;
4. Do not place the machine near the heat sources or in the humid environment for a long time;
5. Please use the machine near the electric socket to unplug easily;
6. When clean the machine or repair the damaged plug, please unplug it from the electric socket at first;
7. Machine must be far away from children and pets;
8. If the machine is not to use for a long time, please cut off the electric power and unplug.
Working Condition
Temperature: 25
SAFETY SYMBOLS
Warming: Please pay more attention to the safety instruction , before operate the
machine otherwise wrong operation will result in danage to users.
The mark “O” Printed on The machine means, the machine is off when the button
is in this location.
Product is not intended for use
by children (product is not a
toy).
Avoid hair touching the
document feed opening.
Avoid touching the document
feed opening with hands.
Do not insert paper clips or
staples into the infeed slot.
Avoid clothing and long
necklaces or bracelets
touching the document feed
opening.
Keep aerosol products away
(for products incorporating a
universal (brush ) motor.
Paper feed or positive
rotation is normal, but there
is still some scrapped paper
hanging at the exit after
finishing.
The slots of the blades
clamp the scrapped paper.
Set the slide switch to
“REV”(if need, please clean
the scrapped paper at the
exit).
Some paper in the entry, but
shredder does not work.
After feeding paper, any
corner of the paper is
inserted, but the rest doesn’t
touch automatic inductive
device.
Adapt to the position of the
feeding paper and
push&make it touch the
automatic inductive device.