Flotec E5005TLT Setup guide

© 2011 FP942 (8/2/2011)
E3305TLT, E5005TLT
INSTALLATION AND OPERATOR’S MANUAL
Submersible Sump/Effluent Pump
MANUEL D’INSTALLATION ET L’OPÉRATEUR
Pompes submersibles de puisard et
pour effluents
MANUAL DE INSTALACIÓN Y OPERARIO
Bombas sumergible de
sumidero/efluente
293 Wright Street, Delavan, WI 53115
Phone: [phone]
Fax: [phone]
Web Site: flotecwater.com
Installation/Operation/Parts
For further operating, installation, or
maintenance assistance:
Call 1-800-365-6832
English............Pages 2-8
Installation/Fonctionnement/Pièces
Pour plus de renseignements
concernant l’utilisation,
l’installation ou l’entretien,
Composer le 1 [phone]
Français..........Pages 9-15
Instalación/Operación/Piezas
Para mayor información sobre el
funcionamiento, instalación o
mantenimiento de la bomba:
Llame al 1-800-365-6832
Español ....... Paginas 16-22

For parts or assistance, call Flotec Customer Service at 1-800-365-6832
Safety 2
Important Safety Instructions
SAVE THESE INSTRUCTIONS - This manual contains
important instructions that should be followed during
installation, operation, and maintenance of the product.
Save this manual for future reference.
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for one of
the following signal words and be alert to the potential
for personal injury!
indicates a hazard which, if not avoided, will
result in death or serious injury.
indicates a hazard which, if not avoided, could
result in death or serious injury.
indicates a hazard which, if not avoided, could
result in minor or moderate injury.
NOTICE addresses practices not related to personal injury.
Carefully read and follow all safety instructions in this
manual and on pump.
Keep safety labels in good condition.
Replace missing or damaged safety labels.
Description
These submersible sump pumps are designed for home
/ residential sumps or effluent applications. The unit is
equipped with a 3-prong grounding-type power cord.
The shaded-pole motor is oil filled and sealed for
cooler running. Upper sleeve/lower ballbearing on the
motor shaft never need lubrication. Automatic reset
thermalprotection.
NOTICE: This unit is not designed as a waterfall, pond,
or fountain pump, or for applications involving salt water
or brine! Use with waterfalls, fountains, salt water or
brine will void warranty.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.
NOTICE: Read this Owner’s Manual for installation,
operation, and safety information.
Specifications
Power supply required................115V, 60 HZ.
Motor HP
E3305TLT ............................1/3
E5005TLT ............................1/2
Motor Full Load Amps
E3305TLT ...........................9.8 A
E5005TLT ..........................12.5 A
Individual Branch Circuit Required: .........15 Amps
Liquid Temp. Range..........32°F to 130°F (0°-54°C)
Discharge ...........................1-1/2” NPT
Cord Length .........................20’ (6.1 m)
Performance
Model
GPM (LPM) at Total Feet (m) No flow
at height
shown
below
5
(1.5)
10
(3)
15
(4.6)
20
(6.1)
25
(7.6)
30
(9.1)
E3305TLT 48
(182)
40
(151)
29
(110)
15
(57) - - 24 Ft. (7.3m)
E5005TLT 62
(235)
53
(201)
46
(174)
38
(144)
29
(110)
13
(49) 32 Ft. (9.8m)
WARNING
Hazardous voltage. Can
shock, burn, or cause death.
Ground pump before
connecting to power supply.
Disconnect power before
working on pump, motor
ortank.
Wire motor for correct
voltage. See “Electrical”
section of this manual
and motor nameplate.
Ground motor before
connecting to
powersupply.
Meet National Electrical
Code, Canadian
Electrical Code, and
local codes for
allwiring.
Follow wiring
instructions in this
manual when
connecting motor to
power lines.

For parts or assistance, call Flotec Customer Service at 1-800-365-6832
Warranty 3
Retain Original Receipt For Warranty Eligibility
Limited Warranty
This Limited Warranty is effective June 1, 2011 and replaces all undated warranties and warranties dated before June 1, 2011.
FLOTEC warrants to the original consumer purchaser (“Purchaser” or “You”) that its products are free from defects in material and
workmanship for a period of twelve (12) months from the date of the original consumer purchase. If, within twelve (12) months
from the original consumer purchase, any such product shall prove to be defective, it shall be repaired or replaced at FLOTEC’s
option, subject to the terms and conditions set forth herein. Note that this limited warranty applies to manufacturing defects only
and not to ordinary wear and tear. All mechanical devices need periodic parts and service to perform well. This limited warranty
does not cover repair when normal use has exhausted the life of a part or the equipment.
The original purchase receipt and product warranty information label are required to determine warranty eligibility. Eligibility
is based on purchase date of original product – not the date of replacement under warranty. The warranty is limited to repair or
replacement of original purchased product only, not replacement product (i.e. one warranty replacement allowed per purchase).
Purchaser pays all removal, installation, labor, shipping, and incidental charges.
For parts or troubleshooting assistance, DO NOT return product to your retail store - contact FLOTEC Customer Service at
1-800-365-6832.
Claims made under this warranty shall be made by returning the product (except sewage pumps, see below) to the retail outlet
where it was purchased or to the factory immediately after the discovery of any alleged defect. FLOTEC will subsequently take
corrective action as promptly as reasonably possible. No requests for service will be accepted if received more than 30 days after
the warranty expires. Warranty is not transferable and does not apply to products used in commercial/rentalapplications.
Sewage Pumps
DO NOT return a sewage pump (that has been installed) to your retail store. Contact FLOTEC Customer Service. Sewage pumps
that have seen service and been removed carry a contamination hazard with them.
If your sewage pump has failed:
• Wearrubbergloveswhenhandlingthepump;
• Forwarrantypurposes,returnthepump’scordtagandoriginalreceiptofpurchasetotheretailstore;
• Disposeofthepumpaccordingtolocaldisposalordinances.
Exceptions to the Twelve (12) Month Limited Warranty
Product Warranty Period
FP0F360AC, FP0FDC 90 days
FP0S1775A, FP0S1790PCA, FP0S2400A, FP0S2450A, FP0S4100X, FP2800DCC, FPCP-20ULST, FPPSS3000, FPPSS5000,
FPSC2150A, FPSC3150A, FPSC3350A 2 Years
4” Submersible Well Pumps, FP0S3200A, FP0S3250A, FP0S6000A, FPSC1725X, FPSC2200A, FPSC2250A, FPSE3601A 3 Years
FP7100 Series Pressure Tanks, E100ELT, E3305TLT, E3375TLT, E5005TLTT, E50TLT, E50VLT, E75STVT, E75VLT, FPSC3200A,
FPSC3250A, FPSC4550A 5 Years
General Terms and Conditions; Limitation of Remedies
You must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty does not
applytothefollowing:(1)actsofGod;(2)productswhich,inFLOTEC’ssolejudgment,havebeensubjecttonegligence,abuse,
accident,misapplication,tampering,oralteration;(3)failuresduetoimproperinstallation,operation,maintenanceorstorage;(4)
atypicalorunapprovedapplication,useorservice;(5)failurescausedbycorrosion,rustorotherforeignmaterialsinthesystem,
or operation at pressures in excess of recommended maximums.
This warranty sets forth FLOTEC’s sole obligation and purchaser’s exclusive remedy for defective products.
FLOTEC SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.
THE FOREGOING LIMITED WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. THE FOREGOING LIMITED WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION
PROVIDED HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an
implied warranty lasts, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights
and You may also have other rights which vary from state to state.
FLOTEC • 293 Wright Street • Delavan, WI U.S.A. 53115
Phone: [phone] • Fax: [phone] • Web Site: flotecwater.com

For parts or assistance, call Flotec Customer Service at 1-800-365-6832
Safety 4
General Safety Information
Electrically powered sump pumps normally give many
years of trouble-free service when correctly installed,
maintained, and used. However, unusual circumstances
(interruption of power to the pump, dirt/debris in the
sump, flooding that exceeds the pump’s capacity,
electrical or mechanical failure in the pump, etc.)
may prevent your pump from functioning normally. To
prevent possible water damage due to flooding, consult
your dealer about installing a secondary sump pump, a
DC backup sump pump, and/or a high water alarm. See
Troubleshooting in this manual for information about
common sump pump problems and remedies. For more
information, see your dealer or call customer service at
1-800-365-6832.
1. Know the pump application, limitations, and
potential hazards.
2. Disconnect the power before servicing.
3. Release all pressure within the system before
servicing any component.
4. Drain all water from the system before servicing.
5. Secure the discharge line before starting the pump.
An unsecured discharge line will whip, possibly
causing personal injury and/or property damage.
6. Check the hoses for a weak or worn condition before
each use. Make certain all connections are secure.
7. Periodically inspect the sump, pump and system
components. Keep free of debris and foreign objects.
Perform routine maintenance as required.
8. Provide a means of pressure relief for pumps whose
discharge line can be shut-off or obstructed.
9. Personal Safety:
a. Wear safety glasses at all times when working
with pumps.
b. Keep the work area clean, uncluttered and
properly lighted – replace all unused tools
andequipment.
c. Keep visitors at a safe distance from work area.
d. Make the workshop child-proof – with padlocks,
master switches, and by removing starter keys.
10. When wiring an electrically driven pump, follow all
electrical and safety codes that apply.
11. This equipment is only for use on 115 volt
(single phase) and is equipped with an approved
3-conductor cord and 3-prong, grounding-type plug.
Electrical shock hazard. Can burn or kill.
To reduce risk of electric shock, pull plug before
servicing. Pump is supplied with a grounding
conductor and grounding-type attachment plug. Be
sure it is connected only to a properly grounded
grounding-type receptacle.
Where a 2-prong wall receptacle is encountered, it
must be replaced with a properly grounded 3-prong
receptacle installed in accordance with codes and
ordinances that apply.
12. All wiring should be performed by a
qualifiedelectrician.
13. Make certain the power source conforms to the
requirements of your equipment.
14. Protect the electrical cord from sharp objects,
hot surfaces, oil, and chemicals. Avoid kinking
the cord. Replace or repair damaged or worn
cordsimmediately.
15. Do not touch an operating motor. Modern motors
are designed to operate at high temperatures.
16. Do not handle the pump or pump motor with wet
hands or when standing on wet or damp surface, or
in water.
Electrical shock hazard. Can burn or kill. If
your basement has water or moisture on floor, do not
walk on wet area until all power has been turned off.
If shut-off box is in basement, call electric company
or hydro authority to shut-off service to house, or call
your local fire department for instructions. Remove
pump and repair or replace. Failure to follow this
warning can result in fatal electrical shock.
17. Do not install the pump in any location classified as
hazardous by the National Electric Code, ANSI/NFPA
70-1984 or the Canadian Electrical Code.

For parts or assistance, call Flotec Customer Service at 1-800-365-6832
Installation 5
Installation
1. Install the pump in a sump pit with a minimum
diameter of 14” (356mm). The sump depth should be
15”minimum (381mm). Construct the sump pit of
tile, concrete, steel or plastic. Check local codes for
approved materials.
2. The pump should not be installed on clay, earth or
sand surfaces. Clean the sump pit of small stones
and gravel which could clog the pump. Keep the
pump inlet screen clear.
3. Install the pump in the pit so that the
switch operating mechanism has maximum
possibleclearance. Do not lift the pump by the
power cord. See the Cord Lift Warning.
4. Install the discharge plumbing. When using rigid
pipe, use plastic pipe. Wrap the threads with PTFE
pipe thread sealant tape. Screw the pipe into the
pump hand tight +1 – 1-1/2 turns.
NOTICE: Do not use ordinary pipe joint compound
on plastic pipe. Pipe joint compound can
attackplastics.
Risk of flooding. If a flexible discharge
hose is used, make sure the pump is secure in
the sump to prevent movement. Failure to secure
the pump may allow pump movement, switch
interference and prevent the pump from starting
orstopping.
5. To reduce motor noise and vibrations, a short length
of rubber hose (e.g. radiator hose) can be connected
into the discharge line near the pump using
suitableclamps.
6. Install an in-line check valve to prevent backward
flow through the pump when the pump shuts off.
7. Power Supply: The pump is designed for 115V.,
60 Hz., operation and requires a minimum
15or 20 amp individual branch circuit (refer to
Specifications.) Both the pump and switch are
supplied with 3-wire cord sets with grounding-type
plugs. The switch plug is inserted directly into the
outlet and the pump plug inserts into the opposite
end of the switch plug.
Hazardous voltage. Can shock, burn
or kill. The pump should always be electrically
grounded to a suitable electrical ground such as a
grounded water pipe or a properly grounded metallic
raceway, or ground wire system. Do not modify the
cord or plug or cut off the round ground pin.
8. If the pump discharge line is exposed to an outside
sub-freezing atmosphere, the portion of the line
exposed must be installed so any water remaining in
the pipe will drain to the outfall by gravity. Failure to
do this can cause the water trapped in the discharge
to freeze which could result in damage to the pump.
9. After the piping and check valve have been installed,
the unit is ready for operation.
10. Check the operation by filling the sump with
water and observing pump operation through one
complete cycle.
Risk of flooding. Failure to make this
operational check may lead to improper operation,
premature failure, and flooding.
Risk of electrical shock and fire.
1. Attempting to lift or support the pump by
the power cord can damage cord and cord
connections, expose bare wires, and cause a fire or
electrical shock.
2. Use lifting ring or handle on top of pump for
all lifting or lowering of pump. Disconnect the
power to the pump before doing any work on it or
attempting to remove it from the pit.
3. Lifting or supporting the pump by the power cord
will void the warranty.
Risk of electrical shock.
Can burn or kill.
Do not lift pump by power
cord.
WARNING
Cord Lift Warning