Fluke TPS FLEX 18-TF-II Configuration guide

Manual Supplement
© 2011-2018 Fluke Corporation. All rights reserved. x
�
Manual Title: 1760 Users Supplement Issue: 5
Print Date: June 2006 Issue Date: 2/18
Revision/Date: 2, 5/10 Page Count: 5
This supplement contains information necessary to ensure the accuracy of the
above manual. This manual is distributed as an electronic manual on the
following CD-ROM:
CD Title: 1760
CD Rev. & Date: 5, 7/2010
CD PN: 2583518

1760 Users Manual Supplement
2/18 1
Change #1, 57261, 57516
On page 1-7, replace the first figure with:
On page 5-3, under General Specifications, replace the Power Supply with:
Power Supply Nominal 100 to 240 V ac, 50/60Hz, 100 to 350Vdc
Power Supply Operating 83 to 264 V ac, 45 to 65 Hz, 100 to 375Vdc, 35W/70 VA
On page 6-5, under Flexible Current Probes for AC, replace the Model No. Product No. column
with:
Model No.
Product No.
TPS FLEX 18-TF-II
4531837
TPS FLEX 24-TF-II
4531843
TPS FLEX 36-TF-II
4531855
On page 6-18, under General Specification:add the Measurement head cross section
specifications and replace Weight, and Order-number with:
Measurement head cross section: 8 mm (0.3 in)
Weight: Approx. 0.3 kg (0.66 lb)
Order-number: 4531837
On page 6-21, under General Specification, add the Measurement head cross section
specifications and replace Weight, and Order-number with:
Measurement head cross section: 8 mm (0.3 in)
Weight: Approx. 0.35 kg (0.66 lb)
Order-number: 4531843
On page 6-25, under General Characteristics, add the Measurement head cross section
specifications and replace Weight, and Order-number with:
Measurement head cross section: 8 mm (0.3 in)
Weight: Approx. 0.4 kg (0.88 lb)
Order-number: 4531855

Manual Supplement 1760 Users
2 2/18
Change #2, 67378, 67383
On page 1-3, in the Symbols table, replace the CAT II, III, IV entires with:
ÃConforms to relevant South Korean EMC Standards.
CAT II MEASUREMENT CATEGORY II is applicable to test and measuring circuits
connected directly to utilization points (socket outlets and similar points) of the low-
voltage MAINS installation.
CAT III MEASUREMENT CATEGORY III is applicable to test and measuring circuits
connected to the distribution part of the building’s low-voltage MAINS installation.
CAT IV MEASUREMENT CATEGORY IV is applicable to test and measuring circuits
connected at the source of the building’s low-voltage MAINS installation.
On page 1-4, replace Figure 1-1 with:
1-1.bmp
Figure 1-1. CAT
Under Safety Instructions, remove the first sentence.

1760 Users Manual Supplement
2/18 3
On page 1-8, replace Figure 1-3 with:
Grafikview.eps
Figure 1-3. Top View
On page 1-9, replace Table 1-2, with:
Item Description
Mains connection
Mains switch
LED indicators
Ethernet connector
USB connectors
COM1 – serial port
Feature connector (GPS, DCF 77, COM2, alarms, etc.)
Measurement input connectors
Reset button
USB LED
On page 1-15, replace the last sentence in Ethernet port with:
For direct connection of the instrument to a PC, use the cross-linked Ethernet cable (do not
use the gray plug).
Change: USB connectors
To: , , USB connectors reset button, USB LED.
Under the first bullet, replace the sentence with:
USB LED behavior during the USB copy process.

Manual Supplement 1760 Users
4 2/18
Under 2 USB connectors, replace the Note with:
Note
A USB stick must not be pulled out while the USB LED flashes. This can cause permanent
damage to the storage media. Only remove the USB stick while the USB LED is OFF or
statically ON. Do not use the USB and data connection at the same time.
Stored data can be erased by holding down the Reset button while switching on the
instrument. This may be useful if the memory is full and may also resolve connectivity
issues.
On page 1-18, remove the first paragraph Compact Flash Card.
On page 2-4, under Simple Measurements – Function Check, replace the first sentence after
Connect device with:
Connect your computer and the recorder with the Crossover Ethernet cable (do not use the gray plug).
On page 4-4, under Replacement of Battery Pack, replace the 4th bullet with:
•For replacement of the battery pack, use only the original spare part
(PN 3114277).
On page 5-3, under General Specifications, Ambient condition, replace Operating temp. range
with:
Operating temperature range...........0 °C to +50 °C, 32 °F to +122 °F (Startup temp ≥5 °C (41 °F)).
On page 5-3, under General Specifications, remove the Quality system, Protection, Electrical
safety, Environmental, and Emissions/Immunity entries and add:
IP Rating..........................................IEC 60529: IP40
Safety...............................................IEC 61010-1: Overvoltage Category III, Pollution Degree 2
IEC 61010-2-030: As specificed by attached accessory.
Electromagnetic Environment..........IEC 61326-1: Basic
Electromagnetic Compatibility..........Applies to use in Korea only. Class A Equipment (Industrial Broadcasting &
Communication Equipment) [1]
[1] This product meets requirements for industrial (Class A) electromagnetic
wave equipment and the seller or user should take notice of it. This
equipment is intended for use in business environments and is not to be
used in homes.
Radio Frequency Emissions............IEC CISPR 11: Group 1, Class A.
Group 1 have intentionally generated and/or use conductively coupled radio-
frequency energy which is necessary for the internal functioning of the
equipment itself.
Class A equipment is suitable for use in non-domestic locations and/or directly
connected to a low-voltage power supply network.
On page 5-5, replace Flicker with:
Flicker As per IEC 61000-4-15:2010
10 min (PSt), 2 h (Plt)
On pages 6-7, 6-11, 6-15, 6-18, 6-22 and 6-25 replace the Safety Standards with:
•IEC 61010-1: Pollution Degree 2
•IEC 61010-031
•IEC 61010-2-032: 300 V CAT IV

1760 Users Manual Supplement
2/18 5
Change #3, 558
On page 6-4, in the first table, replace footnotes 2 and 3 with:
2sensor + basic unit 0.1 % of Udin = 230 V P-N in accordance with IEC61000-4-30 Class A
- for values <10 % and >150 % of Udin 0.15 % of rdg ±0.48 V
3sensor + basic unit 0.1 % of Udin = 480 V and 600 V P-N in accordance with IEC61000-4-30 Class A
- for values <10 % and >150 % of Udin 0.15 % of rdg ±0.8 V