Fluke TS 19 User manual

TS®19
Portable Test Telephone
PN 2448484
October 2005 Rev. 1 2/09
©2005, 2009 Fluke Corporation. All rights reserved. Printed in China.
All product names are trademarks of their respective companies.
Users Guide

LIMITED WARRANTY AND LIMITATION OF LIABILITY
Each Fluke Networks product is warranted to be free from defects in material and workmanship under
normal use and service. The warranty period for the mainframe is 18 months and begins on the date of
purchase. Parts, accessories, product repairs and services are warranted for 90 days, unless otherwise stated.
Ni-Cad, Ni-MH and Li-Ion batteries, cables or other peripherals are all considered parts or accessories. The
warranty extends only to the original buyer or end user customer of a Fluke Networks authorized reseller,
and does not apply to any product which, in Fluke Networks’ opinion, has been misused, abused, altered,
neglected, contaminated, or damaged by accident or abnormal conditions of operation or handling. Fluke
Networks warrants that software will operate substantially in accordance with its functional specifications
for 90 days and that it has been properly recorded on non-defective media. Fluke Networks does not warrant
that software will be error free or operate without interruption.
Fluke Networks authorized resellers shall extend this warranty on new and unused products to end-user
customers only but have no authority to extend a greater or different warranty on behalf of Fluke Networks.
Warranty support is available only if product is purchased through a Fluke Networks authorized sales outlet
or Buyer has paid the applicable international price. Fluke Networks reserves the right to invoice Buyer for
importation costs of repair/replacement parts when product purchased in one country is submitted for repair
in another country.
Fluke Networks warranty obligation is limited, at Fluke Networks option, to refund of the purchase price,
free of charge repair, or replacement of a defective product which is returned to a Fluke Networks
authorized service center within the warranty period.
To obtain warranty service, contact your nearest Fluke Networks authorized service center to obtain return
authorization information, then send the product to that service center, with a description of the difficulty,
postage and insurance prepaid (FOB destination). Fluke Networks assumes no risk for damage in transit.
Following warranty repair, the product will be returned to Buyer, transportation prepaid (FOB destination).
If Fluke Networks determines that failure was caused by neglect, misuse, contamination, alteration, accident
or abnormal condition of operation or handling, or normal wear and tear of mechanical components, Fluke
Networks will provide an estimate of repair costs and obtain authorization before commencing the work.
Following repair, the product will be returned to the Buyer transportation prepaid and the Buyer will be
billed for the repair and return transportation charges (FOB Shipping point).
THIS WARRANTY IS BUYER’S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OR MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. FLUKE NETWORKS SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY
CAUSE OR THEORY.
Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or
limitation of incidental or consequential damages, the limitations and exclusions of this warranty may not
apply to every buyer. If any provision of this Warranty is held invalid or unenforceable by a court or other
decision-maker of competent jurisdiction, such holding will not affect the validity or enforceability of any
other provision.
4/04-18
Fluke Networks
PO Box 777
Everett, WA 98206-0777
USA

1
TS®19 Portable Test Telephone
Contents
Title Page
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Registration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Contacting Fluke Networks . . . . . . . . . . . . . . . . . 1
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . 1
Physical Characteristics. . . . . . . . . . . . . . . . . . . . . 2
Handgrip Controls. . . . . . . . . . . . . . . . . . . . . . . . . 2
Keypad Controls and Indicators. . . . . . . . . . . . . . 3
Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Introduction
The TS19 Portable Test Telephone, often called a “butt-
in,” is a self-contained, line-powered, portable handset
used by installers, repair technicians, and other
authorized personnel for line testing and temporary
communications.
The TS19 Portable Test Telephone provides both DTMF
(Touch Tone) and dial pulse output. The TS19 also
provides last number redial, dual monitor impedance,
an electronic ringer (on/off), and field replaceable line
cords and belt clips.
Registration
Registering your product with Fluke Networks gives
you access to valuable information on product updates,
troubleshooting tips, and other support services. To
register, fill out the online registration form on the
Fluke Networks website at www.flukenetworks.com/
registration.
Contacting Fluke Networks
www.flukenetworks.com
[email protected]
[phone] or 1-800-283-5853
• Australia: 61 (2) 8850-3333 or 61 3 9329 0244
• Beijing: 86 (10) 6512-3435
• Brazil: 11 3759 7600
• Canada: 1-800-363-5853
• Europe: [phone]
• Hong Kong: 852 2721-3228
• Japan: 03-3434-0510
• Korea: 82 2 539-6311
• Singapore: [phone]
• Taiwan: (886) 2-227-83199
Visit our website for a complete list of phone numbers.
Safety Information
The following IEC symbols are used either on the test
set or in the manual:
W
Warning: Risk of personal injury. See the
manual for details.
Caution: Risk of damage or destruction to
equipment or software. See the manual for
details.
XWarning: Risk of electric shock.
.Earth ground
PConformité Européenne. onforms to relevant
European Union directives.
)CAN/CSA-C22.2 No. 60950-1-03
CAN/CSA-C22.2 No. 1010.1-92 + CSA-C22.2 No.
1010.1B-97, UL/ANSI 3111-1
~Do not put products containing circuit boards
into the garbage. Dispose of circuits boards in
accordance with local regulations.

2
TS19 Portable Test Telephone
Users Guide
WXWarning
Good safety practices prohibit the
connection of the TS19 and similar test sets
to 117 volts AC commercial electrical power;
should the TS19 be connected to commercial
power, all warranties are voided.
The TS19 Portable Test Telephone is not
designed to meet the outside plant
requirements of Bellcore Publication TR-TSY-
000344. It is recommended that this product
not be used outside during adverse and/or
wet weather conditions.
Do not use the test set if it is damaged.
Before you use the test set, inspect the case.
Look for cracks or missing plastic. Pay
particular attention to the insulation
surrounding the connectors.
If this product is used in a manner not
specified by the manufacturer, the
protection provided by the product may be
impaired.
Physical Characteristics
See Figure 1.
bdn01.eps
Figure 1. Physical Characteristics
A The case is designed to give rugged service and
withstand the rough handling and shocks
normally associated with craft tools.
B The back of the handgrip is contoured and has a
non-slip surface, freeing both hands while the
Portable Test Telephone rests on the shoulder.
C The keypad has 12 keys on a black plastic bezel
that is recessed into the receiver end of the
housing. The recessed bezel protects the keypad
and prevents accidental key presses.
D The spring-loaded belt clip ensures a secure
connection to a belt loop or D-ring. The belt clip
may be replaced in the field (see Belt Clip
Replacement).
E The Portable Test Telephone is equipped with one
of two cord configurations. The line cords may be
replaced in the field.
Handgrip Controls
See Figure 2.
bdn02.eps
Figure 2. Handgrip Controls
A Last Number Redial Button: The LNR button serves
as a last number dialed key. The number may be
redialed in either pulse or tone mode as selected
by the PULSE/TONE switch. The last number dialed
may be up to 18 digits long.
Note
The redial memory has a 15-minute time limit
after the TS19 has been disconnected from a
working telephone line. After 15 minutes, the
number will be lost from memory.

3
Keypad Controls and Indicators
B HI Z/RING/TALK Switch: This three-position slide
switch is labeled as HI Z for high impedance
monitoring, RING for ringer and low impedance
monitoring, and TALK for talk.
• In the HI Z position, the TS19 is on hook with a
high impedance coupling to the telephone line.
This allows for telephone line monitoring without
disrupting conversations, data or signaling.
• In the RING position, the TS19 is on hook with an
electronic ringer connected to the telephone line.
The TS19 is low impedance coupled to the line for
monitoring of optional line identification tones.
Also, the TS19 provides enhanced receive levels.
• In the TALK position, the TS19 is off hook and may
be used for dialing and talking. In this mode, the
TS19 performs as an ordinary telephone.
C PULSE/TONE switch: This two-position slide switch
labeled PULSE/TONE, is located on the inside of
the handgrip just below the receiver. The switch
selects the signaling output. TONE for DTMF of
PULSE for dial pulse.
Keypad Controls and Indicators
See Figure 3.
Keys: The 12 standard keys will send either DTMF tones
or dial pulses, depending on the PULSE/TONE switch
setting.
Polarity LED: This red LED is located just below the
keypad. The LED indicates polarity (see “Polarity
Check”). The red LED lights if the red test lead is
connected to the Tip (positive) side and the black test
lead is connected to the Ring (negative) side.
bnd03.eps
Figure 3. Keypad
Cords
See Figure 4.
The TS19 comes with either a standard cord or an
angled bed-of nails cord (see
B and D below). The line
cord can be replaced in the field (see “Line Cord
Replacement”).
bdn04.eps
Figure 4. Line Cords
Various cord types may be ordered for field
replacement:
A Piercing Pin Cord: This cord is equipped with a
modular plug on one end, and has two five and
one half foot long fabric covered leads, one red
and one black. Each conductor is fitted with an
alligator clip offset 20 degrees to minimize clip
shorting. The clips have insulation piercing spikes
and a neoprene boot. Cord Number: P1980001.
B Banana Jack Cord (STD): This is the standard cord.
This cord is equipped with a modular plug at one
end and two banana jacks at the other with
alligator clip adapters. Cord Number: P1980003.

4
TS19 Portable Test Telephone
Users Guide
C Ground Start Cord: This cord consists of two
conductors with alligator clips. In addition, the red
(ring) conductor has a banana jack attached. This
jack is located six inches below the Portable Test
Telephone and is partially covered by the outer
fabric of the cord. A separate cord is also included.
This cord is 36 inches long with a banana plug on
one end and an alligator clip on the other. Cord
Number: P1980007.
D Angled Bed-of-Nails Cord (ABN): This cord is
similar to the standard cord (STD), except that
each alligator clip is equipped with a “bed-of-
nails” and an insulation piercing spike. Cord
Number: P1980009.
Operation
WXWarning
When connecting to metallic network wires,
always handle alligator clips by the
insulated boots.
Monitoring: Move the HI Z/RING/TALK switch to HI Z
and connect the line leads to the telephone line under
test. Monitoring may now be done without disrupting
traffic.
Polarity Check: Move the HI Z/RING/TALK switch to
TALK. Connect the line leads to the telephone line
under test. The red LED lights if the red test lead is
connected to the Tip (positive) side and the black test
lead is connected to the Ring (negative) side.
Dialing:
1 Move the PULSE/TONE Switch to PULSE or TONE,
depending on the type of dial signaling required.
Move the HI Z/RING/TALK switch to HI Z. Connect
the line cord clips to the telephone line. Listen to
verify that the telephone line is idle.
2 Move the HI Z/RING/TALK switch to TALK and
verify that dial tone is received (when finished).
Enter the desired number to be called on the
keypad. If tone signaling is selected, the tones for
each digit are generated as each key is pressed. If
rotary dial pulse signaling is selected, the desired
number may be entered at any rate on the
keypad; digits will automatically be pulsed out at
the correct rate. To end the call, move the HI Z/
RING/TALK switch to the HI Z position.
Last Number Redial: The last number dialed can be
automatically redialed with the PULSE/TONE switch set
to PULSE or TONE. Use the following procedure for a
number up to 18 digits long:
1 Go on hook (move the HI Z/RING/TALK switch to
the HI Z position) for at least ½ second.
2 Move the HI Z/RING/TALK switch back to the TALK
position.
3 Press the LNR button and the number will be
automatically redialed.
Note
The redial memory has a 15 minute time limit
after the Portable Test Telephone has been
disconnected from a working telephone line.
After 15 minutes, the number will be lost from
memory.
Electronic Ringer (On/OFF): Move the HI Z/RING/TALK
switch to RING and connect line leads to the telephone
line. The piezo-electric transducer electronic ringer will
“ring” whenever it detects ringing voltage on the line.
Answer the call by moving the HI Z/RING/TALK switch
to TALK. To disable the ringer, move the HI Z/RING/
TALK switch to HI Z.
Troubleshooting
The following troubleshooting procedures are based
largely on the audible click heard in the receiver of the
TS19 when the two Portable Test Telephone leads are
placed on battery potential and ground respectively, or
across the terminal of an electrically charged capacitor.
These clicks and other sounds can help you locate open
circuits, shorts, crosses, and grounds.

5
Maintenance
To locate a short circuit: Open one side of the
telephone line and place the test set in the loop — one
lead to each side of the opened line. On the CO side of
the fault, a loud click will be heard. On the field side of
the fault, no click will be heard.
To locate an open circuit: Bridge the test set across the
circuit line — one test lead on tip, the other on ring.
Moving away from the CO, the fault is at the point
where the loud click disappears.
To verify continuity: Place one of the line leads on a
local ground and the other on the conductor in
question. On a good Ring conductor, a click will be
heard. On a good Tip conductor, an inductive hum will
be heard (due to the difference in ground potential
between the CO ground and the local ground).
WWarning
When testing circuits close to the battery
source, the clicks may be loud enough to
hurt your ear if the receiver is held too
tightly against the ear. The TS19 is designed
to rest comfortably on the shoulder with the
receiver away from the ear. It should be
used in this position when listening for
clicks.
Maintenance
WXWarning
Disconnect clips from any metallic
connections before performing any
maintenance. Read all instructions
completely and understand possible hazards
to end user if not performed by authorized
service personnel.
WCaution
Do not use CRC Cable Clean®or any similar
chlorinated solvent on the TS19. Doing so
will damage the TS19 Test Telephone.
Belt Clip Replacement
The ordering number for the replacement belt clip is
P3218249. To replace the belt clip assembly:
1 Place the TS19 on a firm and level working surface
with the keypad up.
2 Remove the two screws which secure the belt clip
to the TS19’s plastic grip (one screw also secures
the strain relief cord). Remove and discard the old
belt clip.
3 Position the new belt clip so that its screw
mounting holes line up with the mounting holes
in the TS19. Insert the screws and tighten. Make
sure the strain relief for the cord is properly
reinstalled.
Line Cord Replacement
To replace the line cord:
WXWarning
Disconnect from telephone network when
replacing line cord.
1 Place the TS19 on a firm and level working surface
with the keypad up.
2 Remove the screw and the strain relief cord.
3 Depress the plastic tang on the modular plug of
the line cord where it enters the TS19’s modular
jack and gently pull the plug and cord free from
the jack. Discard the cord.
4 Insert the modular plug of the replacement cord
into the TS19’s modular jack and listen for a click.
The click indicates that the plug has “locked” into
position with its tang properly engaged to prevent
accidental removal.
5 Reinstall the screw for the strain relief cord.

6
TS19 Portable Test Telephone
Users Guide
Specifications
Electrical
Loop Limit 2.4 kΩmaximum at 48 VDC (nominal 15 mA minimum loop
current)
DC Resistance (Talk Mode) 150 Ωtypical at 80 mA current
AC Impedance (Monitor Mode) Low impedance (Ring position) 600 Ωat 1 KHz typical
High impedance (HI Z position) 100 kΩminimum at 1 KHz
Rotary Dial Output
Pulsing Rate
Percent Break
Interdigit Interval
Leakage During Break
10 pps +0.5 pps
60 % ± 2 %
800 ms typical
> 50 kΩ
DTMF Output
Tone Frequency Error
Level per Tone Pair
±1 % maximum
+2 dBm maximum, -8 dBm minimum
High versus Low Tone Difference 4 dB maximum
Physical
Length 8.75 in (22.2 cm)
Width 2.375 in (6.03 cm)
Height 3.375 in (8.57 cm)
Weight 10.8 oz (.307 kg) maximum
Environmental
Temperature Operating: -5 °C to +40 °C
Storage: -40 °C to +66 °C
Drop 1 m, 4 times
Altitude To 3,000 m (10,000 ft) maximum
Relative Humidity 10 %to 80 % (non-condensing)
Regulatory Standards Used
47 CFR Part 15, Subpart B
ICES-003 Issue 3
AS/NZS 3548
EMC Directive 89/336/EEC, EN 55022:98, EN 61326:97, A1:98 Annex C, EN 61000-4-2, EN 61000-4-3
LV Directive 73/23/EEC, EN 610010.1 (1993)
Certifications and Compliance
Conformité Européenne. Conforms to relevant European Union directives.
CAN/CSA-C22.2 No. 60950-1-03
CAN/CSA-C22.2 No. 1010.1-92 + CSA-C22.2 No. 1010.1B-97, UL/ANSI 3111-1
Specifications subject to change without notice.