Flux Phenom MAGNETIC SCREEN DOOR User manual

FRONT BACK
Visit FluxPhenom.com for our instructional installation videos!
Instructions for Mounting to Wooden Door Frame
Steps:
•Hammer
•Stool or chair to stand on (optional, to help reach top of door frame)
• A second person to assist is recommended
What you will need:
1
Remove the screen door from the package
and unfold it on the floor or table. Connect all
the magnets together so the screen door is
completely shut. Note: the front of the screen
door has the polyester border; the back has
the hook-and-loop border.
Adjust the size of the screen door
2
Hold the top of the screen door on your door frame:a
bWhen holding the screen door to the top of your
door frame, the bottom should hang about 0.5 cm
off the floor. If the screen door is dragging on the
ground as in Figure B, then you will need to "hem"
it at the top, but don't worry this is very easy!
1
YES NO

Adjust the size of the screen door
3
aMounting the top seam of the screen door: Secure
the screen door to the top of the door frame by gently
hammering the thumbtacks into the door frame. It is
best to hammer in 2 thumbtacks (1 on the left side
and 1 on the right side) as shown so you can make
sure the screen door is centered in the middle of the
door frame and that it fits appropriately. You want to
make sure that the screen door is not mounted too
tightly on the sides or it will keep the magnets from
being able to close properly.
Hemming the screen door
(skip this step if no hemming is necessary)
c
2
1) As you're holding the screen door up to the door frame, find the point at the top seam
of the screen door where it sits about a 0.5 cm off the ground. Place your finger at that point.
2) Fold the screen door at that point. The fold should be
from the front to back so that the velcro is not exposed.
Take a thumbtack and push it through both seams to secure
the hem. Do this for the entire top of the screen door, making
sure the hem width is the same across the top.
1) Insert thumbtacks across the top seam about 12-13 cm
apart. Make sure that there are two thumbtacks at the top
middle of the screen door just above where the magnets
connect.

1) Insert the thumbtacks 1 level at a time (1 thumbtack on the left
side and 1 thumbtack at the same level on the right side).
2) While inserting the thumbtacks on each side, always check to make sure that the screen door
is not attached too tightly and test to make sure the magnets can close easily. Also make sure
the screen door is still about a 0.5 cm off the ground.
2) When inserting the thumbtacks along the top seam,
always check to make sure that the bottom of the screen
door is still about a 0.5 cm off the ground. The top seam
should look like this once completed:
bMounting the side seams of the screen door: Insert thumbtacks on each side of the screen door.
The spacing of each thumbtack should be about 30 cm apart. For added security
and durability, reduce spacing to about 15 cm.
FINAL INSTALLATION
3

•Stool or chair to stand on (optional, to help reach top of door frame)
•A second person to assist is recommended
•Scissors
•Paper towels
•Any type of cleaning detergent and isopropyl rubbing alcohol
•If "hemming" is necessary, you can use staples or any type of clip.
Mini binder clips are ideal and you can remove the metal clips after installing.
Side view Back view
What you will need:
Instructions for Mounting to Metal or Aluminum Door Frame:
Steps:
1
Clean entire door frame with any type of cleaning detergent. Then thoroughly wipe down
the door frame with isopropyl alcohol so that the hook-and-loop tape adheres to the frame.
2
Follow steps 1 and 2a and 2b for instructions for Mounting to Wooden Door Frame.
3
Once you find the point where you need to mount the
top seam of the screen door on your door frame, take
the hook-and-loop backing tape that came in the package
and cut so that it is the same length as the top seam
of the screen door. Remove the white film on the
back of the hook-and-loop backing tape and attach to
the top of the door frame:
4
lf your screen door requires hemming:
aThe only difference for hemming
in step 2c for Instructions for Mouning
to Wooden Door Frame, is that you
need to expose the Velcro strip so
that it can be properly mounted to the
backing tape. Only one more fold is
required to do this.
4

cOnce the hem is complete across the entire top seam of the screen door, simply take the
screen door and attach it to the hook-and-loop tape that is on the door frame.
5
Follow step 3 for instructions for Mounting to Wooden
Door Frame but instead of using thumbtacks, use 10-13
cm pieces of the hook-and-loop backing tape to secure
the sides of the screen door to the door frame.
bIn order to secure the hem points, you can use
a stapler or mini binder clips. If you use binder clips,
once the clip is fastened to the mesh, you can remove
the metal pieces.
Contact us directly before contacting Amazon for all customer service needs!
Faster and more knowledgeable service: email one of our customer service experts right now!
Email: [e-mail]
HASSLE FREE RETURNS: If your unit is defective or broken, we will ship you out a new one
ABSOLUTELY FREE. You don't even need to send your old unit back to Amazon!
fluxphenom.com
5