Fly Fly Hobby FF-D005 User manual

1 pc required
800mm
1. Signal cable
(Throttle)
4. Silicone Battery cable (No. 12AWG or 14AWG)
800mm
1 pc required
2 pcs required
800mm
3. Signal cable
(Alieron)
F-86 SABRE
Scale EDF Radio Control model airplane
Model No : FF-D005
UNDER SAFETY PRECAUTIONS
This radio control is not a toy!
- Always keep this instruction manual ready on hand for quick reference.
- Assemble this kit only places out of children reach.
- First-time builders of EDF model should seek the advice of experienced modellers before
beginning assembly and if they do not fully understand any parts of the construction.
- Taking out liability insurance is recommended.
- You are responsible for this model’s assembly and safe operation.
Wingspan : 1420mm
You need to purchase the following accessories separately to complete the assembly.
2 pcs required
800mm
2. Signal cable
(Elevator)
1 pc required
5. 60A Electric Speed Control (ESC) w/BEC
60A
w/ BEC
1 pc required
6. B36 Brushless Motor, 1600-1800kv,
Shaft dia 5mm
5 pcs required
7. Micro servo, 8g, torque >1.0kg
1 pc required
8. Li-Po Battery, 5-cells (18.5v), 3600mAh, 20C
Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
C

A
B
A A
Sharp Hobby Knife
Needle Nose Pliers
Scissors
Awl
8mm Box Driver
Screw driver
Double-sided Tape
Solder Iron (80W above)
Epoxy Glue
A-A-size Batteries
(Transmitter)
Solder
Tools Required
Battery required
Kit contents
1
2
3
5
4
6
7
8
9
10
11
12
13
15
14
16
17
18
19
20
21
22
23
24
25
26
27
4
10
4
3
2
16
2
1
1
3
4
2
1
1
2
1
2
2
2
4
2
1
3
Horn
3x4mm Screw
Linkage stopper
Landing gear
4.0mm
bind nut
4x30mm screw
4x30mm screw
Exhaust pipe
3mm plywood
3mm collar
120x20x3mm
plywood
130x15x3mm
plywood
30x10x3mm
plywood
3mm plywood
3mm plywood
3mm plywood
3mm plywood
3mm collar
1
1
1
Canopy lock
Nose x 1
Main x 2
Foam Glue 1Foam glue
1 x 30 mm wire
3 x 54mm wire
3 x 40mm wire
1x 65mm wire
1x 100mm wire
3 x 4mm screw
Canopy Fuel Tank
Fuselage
Wing
Vertical Tail Wing Horizontal Tail Wing
Ducted Fan Unit Decal
A A
Li-Po Batteries
(Motor)
First-time fliers should seek advice on pre-flight adjustments and assembly from experienced fliers. Remember that flying
a badly assembled or badly adjusted aircraft is very dangerous!
In The beginning, novice fliers should always be assisted by an experienced flier and should never fly alone!
This model aircraft is designed to be powered by an electric-motor. Installing a over power motor and engine, or flying this
model aggressively may lead to serious damage and accidents!
Warning !

Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
C
FLYFLY HOBBY
Horizontal Tail
800mm
Optional servo extension cable required for
the connection of the elevator servos to receiver.
2 pcs required
Elevator
Throttle
To ESC
Battery plug
To ESC
Throttle
Battery
Elevator
Optional extension cable required for
the connection of the ESC.
1 pc required
800mm
1. Single cable
(Throttle)
2. Silicone Battery cable (No. 12AWG or 14AWG)
800mm
1 pc required
1
Fuselage
2
65mm

Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
C
FLYFLY HOBBY
Fuselage
3
A B
A B
Nose Gear
4
Note : Diagram included the optional air retract system.
Please refer to the retract system instruction for
the installation.
Air Retract
system
A B
Don’t mix up the parts of left and right.
The letter marked on the plywood.

Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
C
FLYFLY HOBBY
Fuselage
5
Assembly Fan unit
6
Elevator
Throttle
Battery
Optional
Air valve (main gear)
Connect to main
retract gear air cylinder
(Optional)
Aileron
Connect to aileron servo
Optional extension cable required for
the connection of the aileron servo.
2 pcs required
800mm
1. Single cable
(Alieron)
Note : Install the cable and air tube before glue the fuselage together with epoxy.
A B
(a) Never operate the unit with loose items of clothing or equipment near to the intake area.
(b) Never operate the unit held in your hands as personal injury, or damage to the unit may occur.
(c) Always do a thorough inspection of the unit prior to any operational use.
(d) Always think safety first.
(e) Secure all the screws. If any screws loose while rotating and the serious injury may occur.
Caution : As proper use of the fan unit is out of the influence of the manufacturer, the operation of the fan unit is on
owners risk!
This is not a toy! The unit should only be operated by childs of 12 years and supervised by an adult.

Fan & ESC
7
Wing construction
8
A B
A B
A B
A B
FLYFLY HOBBY
Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
ESC
C

Wing construction
9
10
1
2
2mm Nut
3 x 5 mm
Linkage Stopper
1 x100mm rod
A B
Fin construction
FLYFLY HOBBY
Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
C
A BA B
A B
A B
A B

Copyright 2009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
C
FLYFLY HOBBY
11
Adjustment
12
AA’
BB’
A = A’
B = B’
ELEVATOR
AILERON
25 mm
25 mm
25 mm
25 mm
217 mm
Never fly before checking the CG’s required position.
Reposition the receiver and battery to obtain the correct CG’s location.
NEVER fly the model without well balancing.
184 mm
Adjustment
165mm
150mm
217 mm