Fly Fly Hobby FF-D004 User manual

www.modellmarkt24.ch
Model No : FF-D004
MiG-29
Scale EDF Radio Control model airplane
Wingspan : 1145mm
UNDER SAFETY PRECAUTIONS
This radio control is not a toy!
- Always keep this instruction manual ready on hand for quick reference.
- Assemble this kit only places out of children reach.
- First-time builders of EDF model should seek the advice of experienced modellers before
beginning assembly and if they do not fully understand any parts of the construction.
- Taking out liability insurance is recommended.
- You are responsible for this model’s assembly and safe operation.
1 pc required
1. Signal cable
(Throttle)
3. Silicone Battery cable (No. 12AWG or 14AWG)
800mm
2 pc required
You need to purchase the following accessories separately to complete the assembly.
2 pcs required
800mm
2. Signal cable
(Elevator)
2 pc required
5. 60A Electric Speed Control (ESC) w/BEC
60A
w/ BEC
2 pc required
6. B36 Brushless Motor, 1600-1800kv,
Shaft dia 5mm
2 pcs required
7. Micro servo, torque >1.8kg
2 pc required
4. Li-Po Battery, 5-cells (18.5v), 3600mAh, 20C
Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
C
800mm
www.modellmarkt24.ch

www.modellmarkt24.ch
First-time fliers should seek advice on pre-flight adjustments and assembly from experienced fliers. Remember that flying
a badly assembled or badly adjusted aircraft is very dangerous!
In The beginning, novice fliers should always be assisted by an experienced flier and should never fly alone!
This model aircraft is designed to be powered by an electric-motor. Installing a over power motor and engine, or flying this
model aggressively may lead to serious damage and accidents!
Warning !
Kit contents
A
B
A A
Sharp Hobby Knife
Needle Nose Pliers
Scissors
Awl
8mm Box Driver
Screw driver
Double-sided Tape
Solder Iron (80W above)
Epoxy Glue
A-A-size Batteries
(Transmitter)
Solder
Tools Required
Battery required
A A
Li-Po Batteries
(Motor)
Canopy Vertical Tail Wing
Fuselage
Wing
Horizontal Tail Wing
Ducted Fan Unit
2 pcs
3x4mm Screw
Linkage stopper
Landing gear
3x30mm screw
3x10mm screw
3x20 screw
Canopy lock
1 x 90mm wire
4 x 350
25x10x3 plywood
32x12x3 plywood
42x20x3 plywood
3mm plywood
3mm plywood
3mm plywood
3mm plywood
32x27x3 plywood
30x12x3 plywood
44x20x3 plywood
Exhaust cone
No Parts Qty Description No Parts Qty Description
4
14
2
3
1
20
2
1
1
2
12
2
8
1
8
1
2mm plywood
2
1
Plastic parts
1
1
2
1
2
Foam Glue
2
1
20
21
22
23
24
25
26
27
28
31
30
32
2
3
4
5
6
7
8
9
10
11
13
Nose x 1
Main x 2
Foam glue
Carbon rod
4 x 600
1
4 mm collar
3
29
1
3mm plywood
12
3
Nylon connector
Square stopper
2
1
3
1 x 30mm wire
3 x 54mm wire
2
3x3mm set screw
1
3 x 50mm wire
15
16
17
14
18
19
4 mm
23 mm
3 mm collar
www.modellmarkt24.ch

www.modellmarkt24.ch
FLYFLY HOBBY
Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
1Fuselage
2
Optional extension cable required for
the connection of the ESC.
1 pcs required
800mm
1. Signal cable
(Throttle)
2. Silicone Battery cable (No. 12AWG or 14AWG)
1000mm
2 pc required
Fuselage
Note :
(1) Install the servo cable before installing ducted fan unit.
(2) Use ‘Y’ extension cable to connect the ESC to receiver.
30 x 12 x 3 plywood
ESC
2 pcs required
800mm
1. Signal cable
(Elevator)
Optional extension cable required for
the connection of the and elevator servo.
3 mm plastic parts
www.modellmarkt24.ch

www.modellmarkt24.ch
FLYFLY HOBBY
Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
3Horizontal Tail
4Horizontal Tail
30 x 5.6 x 3mm plywood 20 x 4 x 3mm plywood
Sand a flat surface
7mm 5mm
www.modellmarkt24.ch

www.modellmarkt24.ch
FLYFLY HOBBY
Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
Front fuselage
6Rear fuselage
Battery
Throttle
Elevator
Note : Diagram included the optional air retract system.
Please refer to the retract system instruction for
the installation method in detail.
1
Li-Po
A B
Air retract valve
Air tank
A B
A B
A B
A B
Optional
Optional
Receiver
5
Note : Assemble the front part in step-5 together.
25 x 10 x 3 plywood
32 x 27 x 3mm
plywood
44 x 20 x 3mm
plywood
42 x 20 x 3mm
plywood
32 x 12 x 3mm
plywood
4 mm plastic parts
www.modellmarkt24.ch

www.modellmarkt24.ch
FLYFLY HOBBY
Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
Nose gear
7
Nose gear
8
38 x 9.5 x 3 plywood
www.modellmarkt24.ch

www.modellmarkt24.ch
FLYFLY HOBBY
Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
Wing construction
9
Wing construction
10
A B
A B
A B
A B
A B
A B
Note : Epoxy half of
the cone only
Note : The cover designed for
removable to access the
motor & EDF.
4 mm plastic parts
4 mm plastic parts
A B
www.modellmarkt24.ch

www.modellmarkt24.ch
FLYFLY HOBBY
Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
11
A
B
12 Adjustment
A
B
4 x 600 carbon rod
4 x 350 carbon rod
160mm 140mm
Assembly
www.modellmarkt24.ch

www.modellmarkt24.ch
FLYFLY HOBBY
Copyright 2007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
Adjustment
14
ELEVATOR/
AILERON
20 mm
20 mm
147mm (5.8’’)
Never fly before checking the CG’s required position.
In order to obtain the CG requirement, reposition the receiver
and battery.
NEVER fly the model without well balancing.
13
Adjustment
A = A’
B = B’
BB’
AA’
Note : Adjust the natural position of the
elevator for level flight
Your radio require the elevon mixing
www.modellmarkt24.ch