Fly Sky FTr10 User manual

FTr10 接收机 Receiver
http://www.flysky-cn.com
Copyright ©2021 Flysky Technology co., ltd
FTr10 采用 AFHDS 3（第三代自动跳频数字系统），双天线双向
传输，它独特设计可节省安装空间，可输出标准 PPM、PWM、
i-BUS 和 S.BUS 信号。
FTr10 adopts AFHDS 3, Flysky's third-generation automatic
frequency hopping digital system. It uses a double-antenna
bidirectional transmission system and is uniquely designed
to save space and output standard PPM、PWM、i-BUS and
S.BUS signals.
产品介绍 Introduction
接收机概览 Receiver overview 用于连接接收机与模型的各个部件。
SENS：连接各传感器。
SENVO：输出 i-BUS/S.BUS 信号，连接扩展模块。
CH 1- CH 10：连接舵机、电源或其他各部件。
BIND：连接对码线。
Power：为飞控供电。
Ports used to connect the receiver to the various
components.
SENS: Connects to sensors.
SENVO: Output i.BUS/S.BUS signal, connect expansion
module.
CH 1 - CH 10: Connects the servos, power supply or other
components.
BIND: For bind cable.
Power: Flight controller power output.
CH 1- CH 7
Bind
CH 8-CH 10
Antenna Antenna
Power
LED
产品规格 Product specication
通道个数：10
适用机型：固定翼 / 滑翔机 / 直升机 / 多轴
数据输出：PWM/PPM/i-bus in/i-bus out/S.BUS
无线频率：2.4GHz
发射功率：<20dBm（EU）
RF 标准：AFHDS 3
天线长度：103 毫米 *2( 双天线 ) 铜管天线
输入电源：3.5V ～ 12V
显示方式：LED 指示
在线更新：有
外形尺寸：52*28*22mm
机身重量：22g
安规认证：CE，FCC ID: N4ZFTR1000
Channels: 10
Model Type: Fixed wing/ glider / helicopter / drone
Data Output: PWM/PPM/i-bus in/i-bus out/S.BUS
RF: 2.4GHz
Transmission Power: <20dBm(EU)
RF standard: AFHDS 3
Antenna: 103mm*2
Input Power: 3.5V ～ 12V
Display: LED Indicator
Online Update: Yes
Dimensions: 52*28*22mm
Weight: 22g
Certi󽗉cation: CE，FCC ID: N4ZFTR1000
对码 Binding
1. 将对码线插入 BIND 接口；
2. 将电源线插入其他任意接口，接收机指示灯快闪表示进入对码
状态；
3. 将发射机进入对码状态；（发射机进入对码状态的方式可能不
同，请根据发射机的使用说明书进行操作）
4. 当接收机指示灯变为常亮时，表示对码成功。将对码线和电源
线从接收机取下。
5. 重新连接电源线至接收机。
6. 检查发射机、接收机、模型是否正常工作。如需重新对码，请
重复以上步骤重新对码。
1. Insert the bind cable into the receivers BIND port;
2. Plug the power cable into any other port, and the receiver's
LED will start to 󽗊ash quickly indicating that it has entered
bind mode.
3. Put the transmitter into bind mode; (See the transmitter's
instruction manual for more information)
4. Binding is successful when the receiver's LED will stop
󽗊ashing. Remove the power and bind cables from the
receiver.
5. Reconnect the power cable to the receiver.
6. Check to make sure that the transmitter and receiver are
working as expected, if there are any issues or unexpected
operation follow the steps above to bind again.
SENS
SERVO
“S”
“+”
“-”
强制更新短接口
（Force update interface）

FTr10 接收机 Receiver
http://www.flysky-cn.com
Copyright ©2021 Flysky Technology co., ltd
强制更新 Forced update
发射机在更新完后，如无法与接收机对码，需强制更新接
收机。
1. 用对码线短接 BIND 和其相隔的信号脚；( 接收机概览
部分已经标注 )
2. 接收机上电进入更新状态（LED 灯三闪一灭），拔掉
对码线，在发射机端选择强制更新。
3. 接收机 LED 灯由 3 闪 1 灭变为慢闪，更新完成。
注意事项：
• 使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。
• 关闭时，请务必先关闭接收机电源，然后关闭发射机。如果关闭发射机电源时接收机仍然在工作，将有可能导致遥控设备失控或者
引擎继续工作而引发事故。
• 确保接收机安装在远离电机，电子调速器或电子噪声过多的区域。
• 接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机天线和导电材料之间至少有 1 厘米以上
的距离。
• 准备过程中，请勿连接接收机电源，避免造成不必要的损失。
Attention:
• Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
• Make sure the receiver's battery is disconnected before turning o󽗈 the transmitter, failure to do so may lead to unintended operation or
loss of control.
• Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise.
• Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.
• Do not power on the receiver during the setup process to prevent loss of control.
失控保护 Failsafe
失控保护功能用于在接收机失去信号不受控制后，接收机按设置好
的失控保护值进行通道输出以保护模型及人员安全。
• 若发射机未设置失控保护通道值输出，接收机在进入失控状
态后 PWM、PPM、i-bus 无输出，S.BUS 保持最后输出；若
发射机设置了失控保护，则按照发射机通道设置值输出。
The failsafe function is used to output the channel according to the
out-of-control protection value set by the user after the receiver
loses its signal and is out of control to protect the model and
personnel.
• If the transmitter has not set the output of the failsafe channel
value, after the receiver enters the out-of-control state, PWM,
PPM, i-bus will not output, and the S.bus will keep the last
output; if the transmitter is set with the failsafe, follow the
transmitter channel setting value Output.
After the transmitter is updated, if the code cannot be matched with the
receiver, it is necessary to update the receiver.
1. Short circuit bind and its separated signal pins with bind cable;（It
has been signed in the Receiver overview part）
2. Power on the receiver to enter the update mode（LED light of the
receiver changes from 3 󽗊ash and 1 o󽗈）, unplug the bind cable, and
select forced update at the transmitter.
3. The LED light of the receiver changes from 3 󽗊ash and 1 o󽗈 to slow
󽗊ash, the update is completed.

FTr10 接收机 Receiver
http://www.flysky-cn.com
Copyright ©2021 Flysky Technology co., ltd
认证相关 Certication
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: changes or modi󽗉cations not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o󽗈
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit di󽗈erent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
EU DoC Declaration
Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FTr10] is in compliance with RED 2014/53/EU.
The full text of the EU DoC is available at the following internet address: www.󽗊ysky-cn.com.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located
oroperating in conjunction with any other antenna or transmitter.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at
the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these
collecting points or to similar collection points. With this little personal e󽗈ort, you contribute to recycle valuable raw materials and the
treatment of toxic substances.
FCC ID:N4ZFTR1000

FTr10 接收机 Receiver
http://www.flysky-cn.com
Copyright ©2021 Flysky Technology co., ltd
认证相关 Certication
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
EU DoC Declaration
Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FTr10] is in compliance with RED 2014/53/EU.
The full text of the EU DoC is available at the following internet address: www.flysky-cn.com.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The
disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the
appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable
raw materials and the treatment of toxic substances.
FCC ID ：N4ZFTR1000