Fly Sky FGr8B User manual

FGr8B 接收机 Receiver
http://www.flysky-cn.com
Copyright ©2020 Flysky Technology co., ltd
产品型号：FGr8B
适 配 发 射 机： 所 有 支 持 AFHDS3 的 发 射 机（PL18、
NB4、NB4 Lite 等）
适合机种：车、船等
PWM 通道：7(2.0 版本将升级为 8 通道 )
无线频率：2.4G
无线协议：AFHDS 3
天线类型：单天线
输入电源：3.5 ～ 9V
数据输出：PWM\PPM\i-bus in
温度范围：-10℃—+60℃
湿度范围：20~95％
在线更新：无线更新
外形尺寸：35*23.3*13.3mm
机身重量：9.4g
认证： CE，FCC ID:N4ZFGR8B
FGr8B 采用 AFHDS3（第三代自动跳频数字系统），
外置单天线带回传功能，设计小巧轻便，易于安装，
可输出 PWM/PPM/i-bus in 信号，支持所有 AFHDS3
发射机和高频头。
The FGr8B receiver adopts Flysky's third-generation automatic frequency
hopping digital system (AFHDS 3).It uses a single-antenna bidirectional
transmission system and is uniquely designed to install and output PWM/
PPM/ i-bus in signals. It supports all AFHDS3 transmitter and RF modules.
产品介绍 Introduction
接收机概览 Receiver overview
对码 Binding
1. 按住接收机对码按键同时上电，松开对码键，接收机指示灯快闪；
2. 打开发射机，进入对码状态；
3. 当接收机指示灯变为常亮时，对码成功 ;
• 当对码的发射机是单向模式进入对码状态时，接收机收到对码信息后指示灯慢闪；然后手动将发射机退出对码状态，接收机指示
灯变为常亮表示对码成功；
4. 检查发射机、接收机、模型是否正常工作。如需重新对码，请重复以上步骤。
产品规格 Product specication
[1] CH1(PWM/PPM)
[2]-[4] CH2-CH4
[5] CH5(NPD)
[6] CH6(NPC)
[7] CH7(NPB)
[8] i-bus in (CH8/NPA)
[9] VCC/BVD（电池电压检测 / 供电
接口）
[10] 天线
[11] 对码按键
[12] LED 灯
[13] S（信号脚）
[14] +（电源正极）
[15] -（电源地）
[16] BVD 功能配件
[17] 接电池正极
[18] 接电池负极
[1] [2]-[4] [9]
[7] [8]
[12]
[10]
[11]
[13]
[14]
[15]
[16] [17]
[18]
注：
(1) NPA/B/C/D 及 BVD 的新功能待后续新程序开放后具备，其中产品内的 BVD 功
能配件请妥善保管，功能升级后将借助该接线实现 BVD 功能；
(2) 1.0 版本的 [8] i-bus in 功能在 2.0 版本后将由 CH8(NPA) 功能取代。
[5][6]
[9] VCC/BVD(Battery voltage detection /
power supply interface)
[10] Antenna
[11] BIND
[12] LED
[13] S（Signal Pin）
[14] +（Positive power terminal）
[15] -（Power ground）
[16] BVD harness
[17] Connect to battery positive pole
[18] Connect to battery negative pole
Tips：
(1) The added new NPA/B/C/D and BVD functions will be available with the release
of a new 󽗉rmware update in September 2020. The BVD harness [17] will not
function until the new 󽗉rmware has been installed.
(2) The [8] i-bus/s.bus terminal will be replaced with the CH8 (NPA) function after
the 󽗉rmware upgrade.
Product Model: FGr8B
Adaptive transmitter: all transmitter supporting AFHDS3 (PL18, NB4,
NB4 Lite, etc.)
Model Type: Car/Boat ect.
PWM Channels: 7（Version 2.0 will be upgraded to 8 channels)）
RF: 2.4GHz
2.4G Protocol: AFHDS 3
Antenna: Single Antenna
Input Power: 3.5-9V
Data Output: PWM\PPM\i-bus in
Temperature Range: -10℃—+60℃
Humidity Limit: 20%-95%
Online Update: Yes
Dimensions: 35*23.3*13.3mm
Weight: 9.4g
Certi󽗉cation: CE，FCC ID:N4ZFGR8B

FGr8B 接收机 Receiver
http://www.flysky-cn.com
Copyright ©2020 Flysky Technology co., ltd
1. Press and hold the receiver BIND button [11] while powering on the receiver, release the BIND button after receiver is powered on, the
LED [12] on the receiver will 󽗊ash rapidly;
2. Put the transmitter into bind mode;
3. The binding process is complete when the LED on the receiver stops 󽗊ashing and is on continuously.
• If a transmitter that has had its radio frequency (RF Standard) set to “AFHDS3 1 way” (please refer to your transmitter user manual)
enters bind mode, the receiver LED will instead 󽗊ash slowly. Exit bind mode on the transmitter and if the receiver LED stops 󽗊ashing
and is on continuously, the binding process is complete.
4. Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems
arise.
对码 Binding
发射机在更新完后，如无法与接收机对码，需强制更新接收机。
1. 接收机按下对码按键，上电十秒钟后指示灯三闪一灭，松开对
码按键；
2. 在发射机端选择接收机更新并进入更新状态；
3. 更新完成指示灯慢闪。
强制更新 Forced update
失控保护功能用于在接收机失去信号不受控制后，保护模型及人员安全。
1. 若发射机未设置失控保护通道值输出，接收机在进入失控保护
状态后将维持失控前输出；若发射机设置了失控保护，则按照
发射机通道设置输出。
失控保护 Failsafe
兼容性 Compatibility
该接收机兼容所有 AFHDS3 的发射机和高频头。（主要包括 PL18、NB4、
NB4 Lite、 FRM302 等）
注意事项：
使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。
关闭时，请务必先关闭接收机电源，然后关闭发射机。如果关闭发射机电源时接收机仍然在工作，将有可能导致遥控设备失控或者引
擎继续工作而引发事故。
确保接收机安装在远离电机，电子调速器或电子噪声过多的区域。
接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机和导电材料之间至少有 1 厘米以上的距离。
准备过程中，请勿连接接收机电源，避免造成不必要的损失。
Attention:
Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
Make sure the receiver's battery is disconnected before turning o󽗈 the transmitter, failure to do so may lead to unintended operation or loss
of control.
Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise.
Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.
Do not power on the receiver during the setup process to prevent loss of control.
If after a 󽗉rmware update is performed and the transmitter is unable
to bind to the receiver, the receiver may need to be put into forced update
times.
1. Power on the receiver while pressing the BIND button [11] for then
approximately ten seconds until the LED [12] 󽗊ashes three
times,release the BIND button.
2. Go to the RX Setup menu on your transmitter and select “RX
Update”.
3. When the receiver LED 󽗊ashes slowly, the update is successful.
This function protects your vehicle by preventing unexpected
behaviors in case of signal lost.
1. Users should always input Fail Safe parameters before operating
their vehicles. If the Fail Safe function has not been set on the
transmitter and signal lost occurs, the receiver will continue
to operate and maintain all output value at the last received
instructions from the transmitter. If the Fail Safe parameters
on the transmitter has set been set, the receiver will set output
values according to user parameters during signal lost.
The FGr8B receiver is compatible with all AFHDS 3 transmitters
and RF modules (including PL18, NB4, NB4 Lite, FRM302 etc.)

FGr8B 接收机 Receiver
http://www.flysky-cn.com
Copyright ©2020 Flysky Technology co., ltd
认证相关 Certication
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: changes or modi󽗉cations not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o󽗈
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit di󽗈erent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
EU DoC Declaration
Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FGr8B] is in compliance with RED 2014/53/EU.
The full text of the EU DoC is available at the following internet address: www.󽗊ysky-cn.com.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at
the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these
collecting points or to similar collection points. With this little personal e󽗈ort, you contribute to recycle valuable raw materials and the
treatment of toxic substances.
FCC ID:N4ZFGR8B