Flymo Power Trim 500 XT User manual

®
Original Instructions
IMPORTANT INFORMATION
Read before use
& retain for future reference
Power Trim
500 XT

Carton Contents
IMPORTANT ! Please check the contents of the carton are correct BEFOREassembling your new Flymo product.
IF ANY PARTS ARE MISSING CONTACT:-
Husqvarna UK Ltd. Customer Service Department direct
Telephone : [phone] Fax : [phone]
Safety
General
1. This product is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning the use of the product by a person
responsible for their safety. Children should be
supervised to ensure that they do not play with the
product. Local regulations may restrict the age of the
operator.
2. Never allow children or people unfamiliar with the
instructions to use the machine.
3. Stop using the machine while people, especially
children, or pets are nearby.
4. Only use the trimmer in the manner and for the functions
described in these instructions.
5. Never operate the trimmer when you are tired, ill or under
the influence of alcohol, drugs or medicine.
6. The operator or user is responsible for accidents or
hazards occurring to other people or their property.
Electrical
AVOIDACCIDENTAL STARTING. REMOVE PLUG FROM
MAINSAND KEEP FEET AWAY FROM THE SWITCH LEVER
WHEN:- CLEANINGAROUND THE INSIDE OF THE SAFETY
GUARD, REMOVINGOR REFITTING SPOOLCAP,
MANUALL
Y FEEDINGOR REPLACINGNYLON LINE.
1. The British Standards Institute recommend the use of a
Residual Current Device (R.C.D.) with a tripping current
of not more than 30mA. Even with a R.C.D. installed
100% safety cannot be guaranteed and safe working
practice must be followed at all times. Check your
R.C.D. every time you use it.
2. Before use, examine cable for damage. If there are signs of
damage or ageing, it must be replaced by the manufacturers
service agent or a similar qualified person to avoid hazard.
3. Do not use the trimmer if the electric cables are
damaged or worn.
4. Immediately disconnect from the mains electricity supply if the
cable is cut, or the insulation is damaged. Do not touch the
electric cable until the electrical supply has been disconnected.
Do not repair a cut or damaged cable. Replace it with a new one.
WARNINGWhen using the product the safety rules must be followed. For your own safety and that of bystanders
please read these instructions before operating the product. Please keep the instructions safe for later use.
Explanation of Symbols on the product
Warning
Read the user instructions carefully to make
sure you understand all the controls and what
they do.
Keep bystanders away. Do not operate
whilst people especially children or pets
are in the area.
The use of eye protection is recommended to
protect against objects thrown by the cutting
parts.
Do not operate in the rain or leave the product
outdoors while it is raining.
Switch off! Remove plug from mains before
adjusting, cleaning or if cable is entangled or
damaged.
Warning: The cutting line continues to rotate
after the machine has been switched off.
360º
10m
Switch Handle
Electric Cable with
moulded on plug
Safety-
Guard
Instruction
Manual
Tube
Steady Handle
Trimmer Head
Plant and
Tree Guard

5. Your extension cable must be uncoiled, coiled cables can
overheat and reduce the efficiency of your trimmer.
6. Keep the cable clear of the cutting area and obstacles at all
times.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting any
plug, cable connector or extension cable.
9. Never pull on the cable to disconnect any of the plugs.
10. Switch off, remove plug from mains and examine electric
supply cable for damage or ageing before winding cable for
storage. Do not repair a damaged cable, replace it with a
new one. Use only Flymo replacement cable.
11. Always wind cable carefully, avoiding kinking.
12. Never carry the product by the cable.
13. Use only on AC mains supply voltage shown on the product
rating label.
14. Our products are double insulated to EN60335. Under no
circumstance should an earth be connected to any part of
the trimmer.
Preparation
1. While using your product always wear substantial footwear
and long trousers.
2. Before using the machine and after any impact, check for
signs of wear or damage and repair as necessary.
3. Inspect the area to be cut before each use. Remove all
objects such as stones, broken glass, nails, wire, string etc,
which can be thrown or become entangled in the trimmer
head.
4. Before use, inspect the area for wildlife, especially hedgehogs.
5. Check that the cutting head is fitted correctly.
Use
1. Use the trimmer only in daylight or good artificial light.
2. Avoid operating your trimmer in wet grass, where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear non-slip
footwear.
5. Do not walk backwards when trimming, you could trip.Walk
never run.
6. Keep cutting head below waist level.
7. Switch off before pushing the trimmer over surfaces other
than grass.
8. Never operate the trimmer with damaged guards or without
guards in place.
9. Never fit metal cutting elements.
10. Keep hands and feet away from the cutting means at all times
and especially when switching on the motor.
11. Never pick up or carry a trimmer by the cable.
12. Do not lean over the trimmer guard - objects may be thrown
by the cutting line.
13. Beware of cut-off pieces of nylon line ejected during use.
14. Remove the plug from the mains :
- before leaving the trimmer unattended for any period;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- if you hit an object. Do not use your trimmer until you are sure that
the entire trimmer is in a safe operating condition;
- if the trimmer starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the trimmer is
in safe working condition.
2. Replace worn or damaged parts for safety.
3. Only use the replacement cutting line specified for this product.
4. Only use replacement parts and accessories recommended
by Husqvarna UK Ltd.
5. After any maintenance in dealing with the cutting line, always return
the product to its normal operating position before switching on.
6. Clean unit with a dry cloth. Never use metal objects to clean
the unit.
7. Inspect and maintain the trimmer regularly. Any repairs must be
carried out by an authorised repairer.
8. Store in a cool dry place and out of reach of children. Do not
store outdoors.
Cables
IMPORTANT
Use only 1.00mm2size cable up to 40 metres length maximum.
Maximum rating:
1.00mm2size cable, 10 amps 250 volts AC.
YOUR PRODUCT IS SUPPLIED WITHAN ELECTRIC
MAINSCABLE WIRED DIRECTLY INTO THE PRODUCT.
1.Flymo Mains Cables and Extension Cables are
available from your local Approved Service Centre.
2.Do not wire an extension cable directly to your product
yourself. Please contact your local Approved Service Centre
for further information on the connectors and kits available.
3.Only use extension cables specifically designed for
outdoor use.
CONNECTORS
Flymo connectors are suitable for use with 2 core cable
only. Under no circumstances should these connectors
be used for earthed products.
All Flymo connectors and cables are of splashproof
construction. They are not waterproof and must not be left
outside permanently nor should they be submerged or
immersed in water. Do not let cable lay or trail through pools
of water or splashed with water from hose pipes.
MAINS PLUG REPLACEMENT
• If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is
inserted into a 13 amp socket.
1.No earthrequired.Flymo products are double insulated to
EN60335 and under no circumstances should an earth be
connected to any part of the product.
2.Ensure the mains voltage suits your product.
3.IMPORTANT!
The wires in the mains lead are coloured in accordance
with the following code:
BLUE - NEUTRAL BROWN - LIVE
The wire which is coloured BLUE must be connected to the
Terminal which is marked with the letter ‘N’ or coloured BLACK.
The wire which is coloured BROWN must be connected to the
Terminal which is marked with the letter ‘L’ or coloured RED.
4.It is important that the outer sheath is clamped
correctly into the 3-pin plug.
5.If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
6.A 5 Amp fuse must be fitted to the Mains Plug.
7.The normal plug fuse and household fuse only protect
the electrical equipment and are not a safeguard
against electrocution.
If your product is hard wired i.e. non-detachable mains
electric cable, a conversion kit and extension cable is avail-
able from all Approved Service Centres whichcan be
found in your localYellow Pages.
Assembly Instructions
A1 A2
Assembly of Switch Handle to Tube (A1)
•Ensure that the internal cable is not twisted.
1. Insert the tube into the switch handle.
2. Push until it clicks into position.
•ENSURE THAT THE TUBE IS FULLY LOCATED BY
ATTEMPTING TO REMOVE IT.
Assembly of Trimmer Head to Tube (A2)
•Ensure that the internal cable is not twisted.
1. Insert the tube into the trimmer head.
2. Push until it clicks into position.
•ENSURE THAT THE TUBE IS FULLY LOCATED BY
ATTEMPTING TO REMOVE IT.
CLICK!
CLICK!

Safety Guard Assembly (B1) & (B2)
1. Locate the safety guard over the cutting head. Ensure
the nylon line is fed through the hole in the safety guard
as illustrated in fig B1.
2. Push into location and turn safety guard in the direction
illustrated in Fig B2, until a click is heard and the safety
guard is securely locked in position.
•ENSURE THE SAFETY GUARD IS SECURELY IN
PLACE BY AT T EMPTING TO TWIST GUARD.
Steady Handle Assembly (C)
1. Depress the two buttons on the sides of the switch han-
dle.
2. Locate the steady handle over the buttons and release
the buttons.
3. Adjust the steady handle to the most comfortable oper-
ating position by depressing the buttons and moving
the handle.
Height Adjustment (D)
1. Turn height adjuster (D1) in the direction indicated to
un-lock (D2).
2. Adjust the length of the tube to the most comfortable
operating position.
3. Turn height adjuster in the opposite direction to lock
(D3).
•ENSURE THAT THE TUBE IS FULLY SECURED.
Cable Restraint (E1) & (E2) (optional)
1. Form loop in mains cable and push the loop through
the slot as illustrated in picture (E1).
2. To secure, position loop over the hook and pull the
cable back through the slot as illustrated in picture (E2).
Assembly Instructions cont’
B2
B1
C
How the automatic line feed works (F)
1. When initially switching on the trimmer, a small length
of line is fed out.
2. A ‘clattering’ noise will be heard when the two nylon
lines hit the line cutter. DO NOT BE ALARMED this is
quite normal. After approximately 5 seconds the line
will be cut to the correct length and the noise will re-
duce as the motor reaches full speed.
• Make sure the motor is up to full speed before trimming
or edging.
3. If the noise of the nylon line being cut cannot be heard,
more line will need to be fed out.
4. To feed more line, it is first necessary to to allow the
motor to stop completely, then re-start, allowing the
motor to reach full speed.
5. Repeat step 4. until you hear the lines hitting against the
cutter. (Do not repeat this procedure more than 6 times)
6. If problems are experienced with the automatic line
feed refer to Fault Finding Chart.
F
line cutter
E1 E2
D
1
3
2
1
2
CLICK!
Double Auto Feed System

•WARNING
• The use of eye protection is recommended.
Do not lean over the trimmer whilst trimming or edging,
objects may be thrown by the cutting line.
Do not allow cutting head to rest on the ground.
Do not overload your trimmer.
Overloading can be avoided by making sure the motor
speed does not drop unduly.
DISCONNECT FROM THE MAINS ELECTRICITY
SUPPLY BEFOREATTEMPTING ANY MAINTE-
NANCE OR ADJUSTMENT.
•BEFORE USE
• Make sure that both lines are fed out.
• Make sure motor is up to full speed before trimming or
edging.
How to trim
1. Hold as illustrated in Fig G.
2. To start, squeeze the switch lever.
3. Cut with nylon line at an angle using the tip. See Fig H1.
4. Swing trimmer in and out of the cutting area taking
small cuts (H2)
5. Line is fed out automatically every time the trimmer
head stops rotating and returns to operating speed.
• Extra line can be fed out manually as described in Man-
ual line feed
6. To stop your trimmer release the switch lever.
Using the Plant & Tree Guard
The Plant and Tree Guard (K1) allows the trimming of
grass close to plants and trees without damaging them
with the cutting line.
1. Flip the guard down as illustrated in Fig J1.
2. Use the trimmer around trees (J2) and near plants.
How to edge
1. To convert to edging mode, press button
(K1) and twist head (K2). An audible "click"
will confirm that the head is locked. Ensure the
Plant and Tree Guard is flipped upwards (K3)
2. Ensure the product is in the correct position
for edging as illustrated in Fig L
3. Hold as illustrated in Fig H.
4. To start, squeeze the switch lever.
5. Rest edger on wheel for extra stability and
line up the edge of the lawn with the two indi-
cators on the guard (M1). Edge in direction in-
dicated in Fig M.
6. To stop your trimmer release the switch
lever.
7. To return to trimming mode, press button
and twist head back the opposite way. An au-
dible "click" will confirm that the head is
locked.
H1
K
G
H2
How to use
1
2
1
M
J1 J2
3
CLICK!
L



NP
1
Using the Shrubbing position
1. By pressing the lever (N1) with your foot, the handle can be lowered into three different positions to enable the use of the
product under shrubs and low obstacles (P).
How to use
To manually feed the nylon line (Q)
1. If required line can be fed out manually.
2. To operate, press and release manual line feed button, whilst gen-
tly pulling on one of the lines until the line reaches the line cutter.
3. When the required amount of line is fed out, gently pull
on the second line (there is no need to press the man-
ual line feed button again).
4. If the line extends past the line cutter, too much line has
been fed out.
5. If too much line is fed out, remove the spool cap and click
spool anti-clockwise until the line is at the desired length.
• Always return the product to its normaloperating position
before switchingon.
Manual line feed
Q
manual line
feed button
To remove spool cap
1. Press and hold in the two cap release latches. (R).
2. Pull cap away from the spoolholder. (R).
When refitting the spool cap
1. Keep all areas of the cap and spoolholder clean. Fail-
ure to do so may prevent the cap being securely lo-
cated in the spoolholder.
2. Replace the cap, pressing firmly DOWN towards the
spoolholder to ensure cap is fully located.
3. Check that the cap is correctly fitted by trying to re-
move it without depressing the two latches.
To r e place nylon line.
For your convenience it is recommended you buy spool and
line complete. Nylon line only is also available. Both are
available from Husqvarna UK Ltd. stockists.
To fit spool and line complete:
1. Remove the cap.
2. Remove old spool.
3. Place spool into spoolholder.
4. Release one line from cleat (T1).
5. Secure line into slot (S1).
6. Repeat for second line.
•Ensure spoolis fully located by gently rotatingit duringfit-
ment,whilst keepingthe spoolholder steady.
7. Refit the cap.
To fit nylon line only:
•Remember! Your Flymo Trimmer is designed to use
only nylon line with a maximum diameter of 1.5mm.
Use only genuine Flymo nylon line.
1. IMPORTANT - Always wind the line onto the upper
section of the spool first.
Take approximately 5 metres of line. Insert 15mm of
line into one of the holes in the upper section of the
spool (T) and wind line in the direction of the arrows on
the top of the spool. Leave approximately 100mm of
line unwound and place into cleat as illustrated in fig-
ure T1. Repeat on lower section of spool.
2. Care should be taken to ensure that the line is neatly
coiled on the spool. Failure to do so will impair the effi-
ciency of the automatic line feed.
3. Then fit spool as described in ‘To fit spool and line
complete’, section above.
• Always return the product to its normaloperating position
before switchingon.
Cap
Cap release
latch
Spool
Spoolholder
Slot
R
S
T
Cleat
S1
Cutting Head
T1

To manually feed the nylon line (Q)
1. If required line can be fed out manually.
2. To operate, press and release manual line feed button,
whilst gently pulling on one of the lines until the line
reaches the line cutter.
3. When the required amount of line is fed out, gently pull
on the second line (there is no need to press the man-
ual line feed button again).
4. If the line extends past the line cutter, too much line has
been fed out.
5. If too much line is fed out, remove the spool cap and click
spool anti-clockwise until the line is at the desired length.
• Always return the product to its normaloperating position
before switchingon.
Manual line feed
To remove spool cap
1. Press and hold in the two cap release latches. (R).
2. Pull cap away from the spoolholder. (R).
When refitting the spool cap
1. Keep all areas of the cap and spoolholder clean. Fail-
ure to do so may prevent the cap being securely lo-
cated in the spoolholder.
2. Replace the cap, pressing firmly DOWN towards the
spoolholder to ensure cap is fully located.
3. Check that the cap is correctly fitted by trying to re-
move it without depressing the two latches.
To r e place nylon line.
For your convenience it is recommended you buy spool and
line complete. Nylon line only is also available. Both are
available from Husqvarna UK Ltd. stockists.
To fit spool and line complete:
1. Remove the cap.
2. Remove old spool.
3. Place spool into spoolholder.
4. Release one line from cleat (T1).
5. Secure line into slot (S1).
6. Repeat for second line.
•Ensure spoolis fully located by gently rotatingit duringfit-
ment,whilst keepingthe spoolholder steady.
7. Refit the cap.
To fit nylon line only:
•Remember! Your Flymo Trimmer is designed to use
only nylon line with a maximum diameter of 1.5mm.
Use only genuine Flymo nylon line.
1. IMPORTANT - Always wind the line onto the upper
section of the spool first.
Take approximately 5 metres of line. Insert 15mm of
line into one of the holes in the upper section of the
spool (T) and wind line in the direction of the arrows on
the top of the spool. Leave approximately 100mm of
line unwound and place into cleat as illustrated in fig-
ure T1. Repeat on lower section of spool.
2. Care should be taken to ensure that the line is neatly
coiled on the spool. Failure to do so will impair the effi-
ciency of the automatic line feed.
3. Then fit spool as described in ‘To fit spool and line
complete’, section above.
• Always return the product to its normaloperating position
before switchingon.
Q
manual line
feed button
Cap
Cap release
latch
Spool
Spoolholder
Slot
R
S
T
Cleat
T1
S1
Cutting Head

Fault Finding Chart
WARNINGDisconnect from the mains electricity supply before attemptingany maintenance or adjustment.
FAULT CHECK ACTION
Is the automatic line feed work-
ing?
Manually feed out line.
SEE “MANUAL LINE FEED”
Is the line fed out and visible?
Has line been removed from
cleat?
Remove cap and spool, free line
and re-fit spool and cap. SEE “CUT-
TING HEAD”
The line may be jammed on the
spool. Rewind line to remove
crossed loops. Check that line is in
correct section of spool.
Is the manual line feed working?
Has too much line been fed out? SEE “MANUAL LINE FEED”
Contact your local approved Serv-
ice Centre or Husqvarna UK Ltd.
Customer Service.
Is the line cutter missing from the
safety guard?
Contact Husqvarna UK Ltd. Customer Service
Te lephone : 0844 844 4558
No
No
No
Ye s
Ye s
LINE NOT FEEDING
OR
LINE TOO SHORT
OR
TRIMMER VIBRATES
CONTINUOUS CLATT ER-
ING NOISE
LINE SNAPS CONTINU-
OUSLY
IF NONE OF THE ABOVE
OR IF FAULT PERSISTS
Has the motor reached full speed
before use?
No
Allow the motor to reach full speed
before use.
Are you using the trimmer cor-
rectly?
?
Only use tip of nylon line to trim.
SEE “How to trim and edge”
Is the line jamming on the spool?
Ye s
Rewind the line on the spool, if
symptoms still persist, change
spool and line.
Maintenance
W
V
•WARNING
Disconnect from the mains electricity supply, before at-
tempting any maintenance or adjustment. Cutting
head continues to rotate after the trimmer has been
switched off. Keep fingers and hands clear of the line
cutter on leading edge of guard.
Caring for your product
After you have finished using your product follow the pro-
cedure below:
AVOID ACCIDENTAL STARTING. REMOVE PLUG
FROM MAINS AND KEEP FEET AWAY FROM THE
SWITCH LEVER WHEN: CLEANING AROUND THE IN-
SIDE OF THE SAFETY GUARD, REMOVING OR REFIT-
TING SPOOL CAP, MANUALLY FEEDING OR
REPLACING NYLON LINE.
1. Disconnect from the mains electricity supply.
2. Never clean your trimmer with water, cleaning fluids, or
solvents, just remove debris with a suitable tool, a soft
brush or dry cloth.
3. Using a soft brush, clean around the inside of the
safety guard, the cutting head (V) and the motor hous-
ing air vents. (W)
4. Inspect the trimmer carefully, especially the parts of
the cutting head.
5. If your trimmer is damaged in any way contact your
local approved service centre.
•Never use a damaged trimmer.
6. Store in a cool, dry place and out of reach of children.
Cable Storage
1. Your mains cable can be stored on the product as illus-
trated in Fig X1.
2. Wind cable carefully to avoid kinking.
3. To release the cable press the button and the hook will
drop down (X2).
4. Push cable hook fully back into position.
X2
X1

5101571-03
If any part is found to be defective due to faulty manufacture within
the guarantee period, Husqvarna UK Ltd., through its Authorised
Service Repairers will effect the repair or replacement to the cus-
tomer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty adjustment
by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken apart or tam-
pered with by any person not authorised by Husqvarna UK Ltd..
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way diminishes the
customers statutory rights.
Failures due to the following are not covered, therefore it is important
that you read the instructions contained in this Operator's Manual
and understand how to operate and maintain your machine:
Failures not covered by guarantee
* Replacing Nylon Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accordance with the in-
structions and recommendations contained in this Operator's Manual.
* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing parts and
their life is dependent on regular maintenance and are, therefore
not normally subject to a valid warranty claim: Nylon Line, Spool
and Line, Electric Mains Cable
* Caution!
Husqvarna UK Ltd. does not accept liability under the warranty
for defects caused in whole or part, directly or indirectly by the
fitting of replacement parts or additional parts that are not either
manufactured or approved by Husqvarna UK Ltd., or by the ma-
chine having been modified in any way.
Guarantee & Guarantee Policy
EC Declaration of Conformity
Husqvarna UK Ltd., Aycliffe Industrial Park
Newton Aycliffe, Co. Durham, DL5 6UP, England
Declare under our sole responsibility that the product(s);
Category............................Electric Lawn Trimmer
Type(s) ............................PTXT25
Identification of Series.......See Product Rating Label
Year of Construction..........See Product Rating Label
Conforms to the essential requirements & provisions of the following EC Directives:
98/37/EC (until 31.12.09), 2006/42/EC (from 01.01.10), 2004/108/EC, 2000/14/EC
based on the following EU harmonized standards applied:
EN60335-1, EN60335-2-91, EN786, EN50366, EN55014-1, EN61000-3-2, EN61000-3-3
The maximum A weighted sound pressure level LpA at the operator’s position, recorded on a sample of the above prod-
uct(s) corresponds to the Level given in the table.
The maximum hand / arm vibration weighted value measured according to EN ISO 5349 on a sample of the above
product(s) corresponds to the Value given in the table.
2000/14/EC:The Measured Sound Power LWA & Guaranteed Sound Power LWA values are according to the tabulated figures.
Conformity Assessment Procedure............... Annex VI
Notified Body................................................. Intertek, Cleeve Road
Leatherhead, Surrey
KT22 7SB, England
Newton Aycliffe 03/03/2009
M.Bowden
Research & Development Director
Husqvarna UK Ltd.
Keeper of technical documentation
Ty pe
Width of Cut (cm)
Speed of Rotation of Cutting Device (rpm)
Power (W)
Measured Sound Power LWA (dB(A))
Guaranteed Sound Power LWA (dB(A))
Level (dB(A))
Value (m/s2)
Weight (Kg)
PTXT25
25
10,750
500
93
96
77
1.74
3.6
• Awareness of the environment must be considered when dis-
posing of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal informa-
tion.
The symbol on the product or on its packaging indicates that this
product may not be treated as household waste. Instead it shall be handed
over to the applicable collection point for the recycling of electrical and elec-
tronic equipment.
By ensuring this product is disposed of correctly, you will help prevent po-
tential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this
product.
For more detailed information about recycling of this product, please con-
tact your local council office, your household waste disposal service or the
shop where you purchased the product.
Environmental Information
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Copyright © 2008 Flymo S.A. All rights reserved. Flymo® and other product and feature names are registered or unregistered trademarks
of Flymo S.A.
Husqvarna UK Ltd.
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
Te lephone - 01325 302302 Fax - 01325 310339