Flymo Speedi Trim User manual

Speedi Trim Art. 9669790-xx
EN Operator’s Manual
Turbotrimmer
®
Remark: “xx” stands for customer and country variants.
The basic product number is before the hyphen.
41025-85.960.01.indd 141025-85.960.01.indd 1 13.09.21 12:0613.09.21 12:06

A1
1
2
click
1
2
A2
4
3
5
A3
click
4
3
A4
3
6
O1
u
i
O2
4
O3
4
O8
8
O10
p
o
M1
3
M2
z
M3
d
ff
h
so j
g
2
41025-85.960.01.indd 241025-85.960.01.indd 2 13.09.21 12:0613.09.21 12:06

M4
o
ß
C
S1
M5
k
3
41025-85.960.01.indd 341025-85.960.01.indd 3 13.09.21 12:0613.09.21 12:06

FLYMO Speedi Trim STXT25
1. SAFETY
Important!
Read the operator’s manual carefully before
use and keep for future reference.
Symbols on the product:
Read operator’s manual.
Keep other persons away.
360°
Danger!
Risk of injury to other persons!
v Keep other persons out of the
work area.
Wear safety glasses and
ear protection.
Do not let the product become wet with
rain or other moisture. Do not leave
the product outdoors while it is raining.
Disconnect the mains cable if
the cable becomes damaged or
entangled.
General safety warnings
Important
Read carefully before use.
Keep for further reference.
Safe operating practices
Training
a) Read the instructions carefully. Be familiar with the
controls and the correct use of the machine.
b) Never allow children or people unfamiliar with these
instructions to use the machine. Local regulations can
restrict the age of operator.
c) Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
Preparation
a) Before use check the supply and extension cord for
signs of damage or aging. If the cord becomes dam-
aged during use, disconnect the cord from the supply
immediately.
DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY.
Do not use the machine if the cord is damaged or
worn.
b) Before use, always visually inspect the machine for
damaged, missing or misplaced guards or shields.
c) Never operate the machine while people, especially
children, or pets are nearby.
Operation
a) Keep supply and extension cords away from cutting
means.
1. SAFETY........................................................................ 4
2. ASSEMBLY ..................................................................6
3. OPERATION................................................................. 6
4. MAINTENANCE............................................................7
5. STORAGE ....................................................................8
6. TROUBLESHOOTING .................................................. 8
7. TECHNICAL DATA .......................................................9
8. ACCESSORIES ............................................................9
9. SERVICE/WARRANTY.................................................. 9
Original instructions.
This product may be used under
supervision, or if instruction
regarding the safe use of the product has
been provided and the resulting dangers
have been understood, by children aged
8 and above, as well as by persons with
physical, sensory or mental disabilities or
a lack of experience and knowledge. Chil-
dren must not be allowed to play with the
product. Cleaning and user maintenance
must not be performed by children with-
out supervision. The use of this product
by young people under the age of 16 is
not recommended. Never operate the
product when you are tired, ill or under
the influence of alcohol, drugs or medi-
cine.
Intended use:
The FLYMO Turbotrimmer is used to trim and to cut grass
and lawns in private house and hobby gardens.
Do not use the product in public facilities, parks, sports
grounds, adjacent to roads or in agriculture or forestry.
DANGER! Risk of injury!
v Do not use the product to cut hedges, to shred
or to make compost.
4
41025-85.960.01.indd 441025-85.960.01.indd 4 13.09.21 12:0613.09.21 12:06

b) Wear eye protection and stout shoes at all times while
operating the machine.
c) Avoid using the machine in bad weather conditions
especially when there is a risk of lightning.
d) Use the machine only in daylight or good artificial light.
e) Never operate the machine with damaged guards or
shields or without guards or shields in place.
f) Switch on the motor only when the hands and feet are
away from the cutting means.
g) Always disconnect the machine from the power
supply (i.e. remove the plug from the mains, remove
the disabling device or removable battery).
1) whenever the machine is left unattended;
2) before clearing a blockage;
3) before checking, cleaning or working on the machine;
4) after striking a foreign object;
5) whenever the machine starts vibrating abnormally.
h) Take care against injury to feet and hands from the
cutting means.
i) Always ensure that the ventilation openings are kept
clear of debris.
Maintenance and storage
a) Disconnect the machine from the power supply
(i. e. remove the plug from the mains, remove the
disabling device or removable battery) before carry-
ingout maintenance or cleaning work.
b) Use only the manufacturer’s recommended replace-
ment parts and accessories.
c) Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
d) When not in use, store the machine out of reach of
children.
Recommendation
The machine should be supplied via a residual current device
(RCD) with a tripping current of not more than 30 mA.
Cables
If extension cables are used, these must comply with the
minimum cross-sections in the table below:
Voltage Cable length Cross section
220 – 240 V / 50 Hz Up to 40 m 1.0 mm2
220 – 240 V / 50 Hz Up to 60 m 1.5 mm2
220 – 240 V / 50 Hz Up to 100 m 2.5 mm2
Minimum rating: 1.0 mm2size cable,
10 amps 250 volts AC.
Your product is supplied with cable wired directly into
the product.
– Flymo Extension Cables are available from your local
Husqvarna UK Ltd. Approved Service Centre.
– Do not wire an extension cable directly to your product
yourself. Please contact your local Husqvarna UK Ltd.
Approved Service Centre for further information on the
connectors and kits available.
– Only use extension cables specifically designed for
outdoor use and which conform to one of the following
specifications: Ordinary rubber (60245 IEC 53),
Ordinary PVC (60227 IEC 53) or Ordinary PCP
(60245 IEC 57).
Connectors – Important
• Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
• All Flymo connectors and cables are of splashproof
construction. They are not waterproof and must not
be left outside permanently nor should they be sub-
merged or immersed in water. Do not let cable lay or
trail through pools of water or splashed with water from
hose pipes.
Mains plug replacement – Important
• If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is
inserted into a 13 amp socket.
1. No earth required. Flymo products are double insulat-
ed to EN60335 and under no circumstances should an
earth be connected to any part of the product.
2. Ensure the mains voltage suits your product.
3. Important! The wires in the mains lead are coloured in
accordance with the following code:
BLUE – NEUTRAL; BROWN – LIVE. The wire which is
coloured BLUE must be connected to the Terminal
which is marked with the letter 'N' or coloured BLACK.
The wire which is coloured BROWN must be connect-
ed to the Terminal which is marked with the letter 'L' or
coloured RED.
4. It is important that the outer sheath is clamped cor-
rectly into the 3-pin plug.
5. If in doubt consult your local Service Repairer or quali-
fied electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the mains plug.
7. The normal plug fuse and household fuse only protect
the electrical equipment and are not a safeguard
against electrocution.
Additional Safety warnings
Warning! Keep toddlers away when you assemble
the unit. Small parts can be easily swallowed. There is
also a risk that the polybag can suffocate toddlers.
Warning! When wearing hearing protection, and
due to the noise produced by the unit, the operator may
not notice persons approaching.
If the unit starts unintentionally when the mains plug is
connected, disconnect the mains at once.
Contact FLYMO Service to check the unit.
Warning! This unit makes an electromagnetic field
while it operates. This field may under some conditions
interfere with active or passive medical implants. To
decrease the risk of conditions that can possibly injure
or kill, we recommend persons with medical implants
to speak with their physician and the medical implant
manufacturer before operating.
If your trimmer is damaged in any way contact your local
approved service centre.
vNever use a damaged trimmer.
5
41025-85.960.01.indd 541025-85.960.01.indd 5 13.09.21 12:0613.09.21 12:06

Inspect the area to be cut before each use. Remove all
objects such as stones, broken glass, nails, wire, string
etc, which can be thrown or become entangled in the
trimmer head.
Warning: The cutting line continues to
rotate after the machine has been switched off.
Warning: Beware of finger entrapment
while putting the upper and the lower shaft
together [Fig. A1].
Unplug the device immediately in case it doesn’t stop
anymore.
Do not lean over the trimmer guard – objects may be
thrown by the cutting line.
Don’t use the trimmer for pond, river, stream, or creek
care. Water in the product could cause a malfunction,
or an electrical shock.
Do not operate the trimmer in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Trimmers create sparks which may ignite the dust
or fumes.
If the unit starts unintentionally when the mains plug
is connected, disconnect the mains at once. Contact
FLYMO to check the unit.
2. ASSEMBLY
Danger! Risk of physical injury!
Cut injury when the product starts
accidentally.
v Before you assemble the product, make sure
that the mains cable is disconnected.
To assemble the trimmer [ Fig. A1/A2/A3/A4 ]:
1. Put the upper shaft 1and the lower shaft 2together
until they make a click (click).
The product is correctly assembled when there is no
gap between the upper shaft and the lower shaft.
2. Put the cover 3on the trimmer head 4while you
feed the cutting filament 5through the opening in the
cover 3.
3. Push the cover 3into the trimmer head 4and turn the
cover 3anti-clockwise (see fig. A3) until it makes a click
(click).
4. Put the screw 6into the cover 3and tighten the
screw 6.
Make sure, the cover 3is securely in place (try to turn
the cover 3).
3. OPERATION
Danger! Risk of physical injury!
Cut injury when the product starts
accidentally.
v Before you connect, adjust or transport the
product, disconnect the mains cable and trans-
port the product by the bottom handle.
To connect the trimmer:
vConnect the mains cable into a 230 V mains socket.
Work position [ Fig. O2/O3 ]:
1. Hold the product by the handle and the upper shaft
so that the trimmer head 4is tilted a small distance
forward.
2. Swing the trimmer head 4in and out of the cutting
area. Take small cuts.
Make sure, the filament does not touch hard objects such
as walls, stones and fences to prevent the filament from
welding together or breaking.
To adjust the plant guard [ Fig. O8 ]:
Down: Working position / Up: Parking position
The plant guard 8allows to trim the grass close to plants
and trees without damaging them with the cutting filament.
v Turn plant guard 8up or down into the required
position until it locks into place.
To start the trimmer [ Fig. O1 ]:
Danger! Risk of physical injury!
Risk of injury if the product does not stop
when you release the start button.
v Do not bypass the safety devices or switches.
For example do not attach the start lever ito
the handle.
To start:
The product is fitted with a two-handed safety device
(start lever iwith safety interlock u) to prevent the
product from being turned on by accident.
1. Push the safety interlock uand pull the start lever i.
2. Release the safety interlock u.
The product will start.
To stop:
v Release the start lever i.
To extend the cutting filament (double auto feed
system) [ Fig. O10 ]:
A clean cut is achieved only with the maximum filament o
length.
The cutting filament ois lengthened automatically
when the filament cassette comes to a standstill after
switch off.
6
41025-85.960.01.indd 641025-85.960.01.indd 6 13.09.21 12:0613.09.21 12:06

4. MAINTENANCE
Danger! Risk of physical injury!
Cut injury when the product starts
accidentally.
v Before you maintain the product, make sure that
the mains cable is disconnected.
To clean the trimmer [ Fig. M1 / M2]:
Danger! Electric shock!
Risk of injury and risk of damage to the
product.
v Do not clean the product with water or with a
water jet (in particular high-pressure water jet).
The airflow slots must always be clean.
1. Clean the airflow slots zwith a soft brush (do not use
a screwdriver).
2. Clean all movable parts after each operation. Especially
remove any grass and dirt from the protective cover 3.
To pull the cutting filament manually out of the
filament cassette [ Fig M3 ]:
A cutting filament that is too short or no longer extends
automatically when the trimmer is turned on can be pulled
out manually.
1. Push and release manual feed button s, while you
gently pull on one of the filaments ountil the filament
reaches the filament limiter.
2. When the required amount of filament is fed out, gently
pull on the second filament (There is no need to push
the manual feed button sagain).
3. If the filament extends past the filament limiter, too
much filament has been fed out. Remove the cassette
cover dand click filament cassette anti-clockwise until
the filament is at the desired length.
Always return the product to its normal operating position
before you start again.
To replace the filament cassette or the cutting
filament:
Danger! Risk of physical injury!
Risk of injury from metal cutting parts!
v Do not use metal cutting parts or replacement
parts and accessories not approved by FLYMO.
Only use original FLYMO Filament Cassettes.
You can order Replacement Filament Cassettes from
your FLYMO dealer or directly from the FLYMO Customer
Service. You can buy either a Replacement Filament
Cassette or the Cutting Filament only.
FLYMO Filament Cassette and Cutting Filament:
FLY021 Part.no.: 513937190
To replace the filament cassette [ Fig. M3 / M4]:
1. Push and hold the two latches f.
2. Remove the cassette cover d.
3. Remove the old filament cassette g.
4. Remove all dirt in the cassette holder h.
5. Release one filament ofrom the cleat xof the new
filament cassette t.
6. Secure the filament ointo one slot j.
7. Pull approximately 10 cm of the filament oout of the
filament cassette gthrough the hole jin the cassette
holder h.
8. Repeat for the second filament.
9. Put the filament cassette ginto the cassette holder h.
Make sure, the filament is not caught and the latches f
are locked.
10. Check that the filament cassette gis correctly
locked. (Try to remove the filament cassette g
without to push the latches f.
To replace the cutting filament [ Fig. M3 / M5]:
1. Remove the filament cassette g.
2. Remove all dirt in the cassette holder h.
3. Take approximately 5 meters of one filament oand
insert it into one of the filament lock holes kin the
filament cassette g.
4. Wind the filament oonto the filament cassette gin
the direction of the arrows on the top of the filament
cassette g. (Wind the first filament on the upper section
of the filament cassette g.)
Make sure, the filament ois neatly winded on the
filament cassette g.
5. Repeat for the second filament.
6. Replace the filament cassette g.
As the filament can only be lengthened in small incre-
ments, it can be necessary in some cases to repeat the
switch-off / switch-on action several times (up to 6 times).
Important is that the filament cassette comes to a com-
plete standstill each time.
The cutting filament has been sufficiently lengthened when,
after switch-on, it audibly strikes the filament limiter p.
The filament cassette has to be replaced when the cutting
filament has been used up:
FLYMO Filament Cassette and Cutting Filament:
FLY021 Part.no.: 513937190
7
41025-85.960.01.indd 741025-85.960.01.indd 7 13.09.21 12:0613.09.21 12:06

5. STORAGE
To put into storage [ Fig. S1 ]:
The product must be stored away from children.
1. Disconnect the mains cable.
2. Clean the product.
3. Wind the cable around the cable hooks.
4. Store the product in a dry area where it has protection
from frost.
Recommendation:
The product can be hung up by the handle. The cutting
head is not put under too much strain if the product is
stowed hanging up.
Disposal:
(in accordance with RL2012/19/EC / S.I. 2013 No. 3113)
The product must not be disposed of to normal
household waste. It must be disposed of in line
with local environmental regulations.
IMPORTANT!
v Dispose of the product through or via your municipal
recycling collection centre.
Problem Possible Causes Remedy
Filament is to short or trimmer
vibrates
Filament not fed out and visible. v Pull the filament until it reaches the
filament limiter
Filament not removed from the cleat. v Remove the filament from the cleat.
Filament is jammed on the filament
cassette.
v Rewind the filament to remove
crossed loops. Check that the fila-
ment is neatly winded. If it does not
help change the filament cassette.
Filament is broken inside the filament
cassette.
v Replace the cutting filament.
Continuous clattering noise Motor has not reached full speed
before use.
v Allow the motor to reach full speed
before use.
Too much filament has been fed out. v Rewind the filament.
Filament limiter is missing. v Contact your local approved
Service Center or Husqvarna UK Ltd.
Customer Service.
Filament snaps continuously You do not use the correct working
position.
v Use the correct working position.
Filament is jammed on the filament
cassette.
v Rewind the filament to remove
crossed loops. Check that the fila-
ment is neatly winded. If it does not
help change the filament cassette.
Poor performance The cassette holder is dirty. v Clean the cassette holder.
For any other malfunctions please contact the Husqvarna UK Ltd. Customer Service.
Repairs must only be done by Husqvarna UK Ltd. service departments or specialist dealers
approved by FLYMO.
6. TROUBLESHOOTING
Danger! Risk of physical injury!
Cut injury when the product starts
accidentally.
v Before you troubleshoot the product, make sure
that the mains cable is disconnected.
8
41025-85.960.01.indd 841025-85.960.01.indd 8 13.09.21 12:0613.09.21 12:06

8. ACCESSORIES
FLYMO Filament Cassette and Cutting Filament FLY021 Part.no.: 513937190
Unit Value (STXT25)
Motor power consumption W 300
Mains voltage V 230
Mains frequency Hz 50
Cutting filament thickness mm 1.5
Cutting width cm 25
Cutting filament supply m 5
Cutting filament feed Manual filament feed system
Speed of cutting filament rpm 10,500
Weight kg 2.5
Sound pressure level LpA1)
Uncertainty kpA
dB(A) 82.3
2.5
Sound power level LWA2)
measured / guaranteed
Uncertainty kWA
dB(A) 89 / 91
2.0
Hand / arm vibration avhw1)
Uncertainty ka
m/s24.5
1.5
Measuring process complying with 1) EN 50636-2-91 2) RL 2000/14/EC / S.I. 2001 No.1701
The stated vibration emission value has been measured according to a standardized test
procedure and can be used for comparison of one electric power tool with another. It can also
be used for preliminary evaluation of exposure. The vibration emission value can vary during
actual use of the electric power tool.
7. TECHNICAL DATA
Service:
Please contact the address on the back page.
Warranty statement:
In the event of a warranty claim, no charge is levied to you
for the services provided.
Husqvarna UK Ltd. grants a warranty for all original FLYMO
new products for two years from the date of original pur-
chase from the retailer, provided that the devices have
been for private use only. This manufacturer’s warranty
does not apply to products acquired second hand. This
warranty includes all significant defects of the product that
can be proved to be material or manufacturing faults.
This warranty is fulfilled by supplying afully functional
replacement product or by repairing the faulty product sent
to us free of charge; we reserve the right to choose
between these options. This service is subject to the fol-
lowing provisions:
• The product has been used for its intended purpose as
per the recommendations in the operating instructions.
• Neither the purchaser nor a third party has attempted to
open or repair the product.
• Only original FLYMO replacement parts and wear parts
have been used for operation.
• Presentation of the receipt.
Normal wear and tear of parts and components (such as
blades, blade fixing parts, turbines, light bulbs, V-belts/
toothed belts, impellers, air filters, spark plugs), visual
changes, wear parts and consumables are excluded from
the warranty.
9. Service/Warranty
9
41025-85.960.01.indd 941025-85.960.01.indd 9 13.09.21 12:0613.09.21 12:06

The undersigned hereby certifies as the authorised
representative of the manufacturer, Husqvarna AB,
561 82 Huskvarna, Sweden, that, when leaving our
factory, the unit(s) indicated below is / are in accordance
with the harmonised EU guidelines, EU standards of safety
and product specific standards. This certificate becomes
void if the unit(s) is/ are modified without our approval.
EC Declaration of Conformity
Description of the product: Lawn Trimmer Speedi Trim
Product type: STXT25
Article-Number: 9669790-xx
CE-Directives: 2006/42/EC
2014/30/EU
2011/65/EU
2000/14/EC
Harmonised EN: EN ISO 12100
EN 60335-1
EN 50636-2-91
Deposited Documentation: GARDENA Technical Documentation,
M. Jäger, Hans-Lorenser-Str. 40, 89079 Ulm
Conformity Assessment according to: 2000/14/EC Procedure: art. 14 Annex VI
Noise level: measured / guaranteed 89 dB(A) / 91 dB(A)
Ulm, 07.09.2021
Authorised representative:
Reinhard Pompe
Vice President Products
Wolfgang Engelhardt
Vice President Supply Chain
In accordance with the German Product Liability Act, we
hereby expressly declare that we accept no liability for
damage incurred from our products where said products
have not been properly repaired by a FLYMO-approved
service partner or where original FLYMO parts or parts
authorised by FLYMO were not used.
Product liability
This manufacturer’s warranty is limited to replacement and
repair of products in accordance with the abovementioned
conditions. The manufacturer’s warranty does not consti-
tute an entitlement to lodge other claims against us as a
manufacturer, such as for damages. This manufacturer’s
warranty does not, of course, affect statutory and contrac-
tual warranty claims against the dealer / retailer.
The manufacturer’s warranty is governed by the law of the
Federal Republic of Germany.
In case of a warranty claim, please return the faulty prod-
uct, together with a copy of the receipt and a description
of the fault, with postage paid to the service address.
Consumables:
The cutting filament and the filament cassette are
consumables and are not included in the guarantee.
10
41025-85.960.01.indd 1041025-85.960.01.indd 10 13.09.21 12:0613.09.21 12:06