Flymo PWT23 User manual

IMPORTANT INFORMATION
Read before use
& retain for future reference
Original Instructions
®
Power Trim

Carton Contents
IMPORTANT ! Please check the contents of the carton are correct BEFOREassembling your new product.
IF ANY PARTS ARE MISSING CONTACT:-
Husqvarna UK Ltd. Customer Service Department direct
Telephone : [phone] UK 1800 882 350 ROI Fax : [phone]
Safety
General
1. This product is not intended for use by persons (in-
cluding children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowl-
edge, unless they have been given supervision or in-
struction concerning the use of the product by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with the
product. Local regulations may restrict the age of the
operator.
2. Never allow children or people unfamiliar with the in-
structions to use the machine.
3. Stop using the machine while people, especially chil-
dren, or pets are nearby.
4. Only use the trimmer in the manner and for the func-
tions described in these instructions.
5. Never operate the trimmer when you are tired, ill or
under the influence of alcohol, drugs or medicine.
6. The operator or user is responsible for accidents or
hazards occurring to other people or their property.
Electrical
1. We recommend the use of a Residual Current Device
(R.C.D.) with a tripping current of not more than 30mA.
Even with a R.C.D. installed 100% safety cannot be
guaranteed and safe working practice must be fol-
lowed at all times. Check your R.C.D. every time you
use it.
WARNING. When using the product the safety rules must be followed. For your own safety and that of by-
standers please read these instructions before operating the product. Please keep the instructions safe for
later use.
Explanation of Symbols on your product
Warning
Read the user instructions carefully to
make sure you understand all the controls
and what they do.
Keep others, including children, pets and
bystanders outside the 10 metre hazard
zone. Stop the trimmer immediately if you
are approached.
The use of eye protection is recom-
mended to protect against objects thrown
by the cutting line.
To avoid the possibility of electric shock,
do not use in damp or wet conditions.
Switch off! Remove plug from mains be-
fore adjusting, cleaning or if cable is en-
tangled or damaged.
Warning: The cutting line continues to rotate after the
machine has been switched off.
360º
10m
Upper Shaft
Switch Lever
Electric Cable with
moulded on plug
Guard
Instruction
Manual
Lower
Shaft
Steady
Handle

2. Before use, examine the cable for signs of damage or
ageing. If the cable is found to be defective, take the
product to an Authorised Service Centre and have
the cable replaced.
3. Do not use the trimmer if the electric cables are dam-
aged or worn.
4. Immediately disconnect from the mains electricity sup-
ply if the cable is cut, or the insulation is damaged. Do
not touch the electric cable until the electrical supply
has been disconnected. Do not repair a cut or dam-
aged cable. Replace it with a new one.
5. Your extension cable must be uncoiled, coiled cables
can overheat and reduce the efficiency of your trimmer.
6. Keep the cable clear of the cutting area and obsta-
cles at all times.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting
any plug, cable connector or extension cable.
9. Never pull on the cable to disconnect any of the plugs.
10. Switch off, remove plug from mains and examine
electric supply cable for damage or ageing before
winding cable for storage. Do not repair a damaged
cable, replace it with a new one. Use only our re-
placement cable.
11. Always wind cable carefully, avoiding kinking.
12. Use only on AC mains supply voltage shown on the
product rating label.
13. Our trimmers are double insulated to EN60335.
Under no circumstance should an earth be con-
nected to any part of the trimmer.
Preparation
1. While using your product always wear substantial
footwear and long trousers.
2. Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.
3. Inspect the area to be cut before each use. Remove
all objects such as stones, broken glass, nails, wire,
string etc, which can be thrown or become entangled
in the trimmer head.
4. Before use, inspect the area for wildlife, especially
hedgehogs.
5. Check that the cutting head is fitted correctly.
Use
1. Use the trimmer only in daylight or good artificial light.
2. Avoid operating your trimmer in wet grass, where fea-
sible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear
non-slip footwear.
5. Do not walk backwards when trimming, you could
trip. Walk never run.
6. Keep cutting head below waist level.
7. Switch off before pushing the trimmer over surfaces
other than grass.
8. Never operate the trimmer with damaged guards or
without guards in place.
9. Never fit metal cutting elements.
10. Keep hands and feet away from the cutting means at
all times and especially when switching on the motor.
11. Never pick up or carry a trimmer by the cable.
12. Do not lean over the trimmer guard - objects may be
thrown by the cutting line.
13. Remove the plug from the mains :
- before leaving the trimmer unattended for any period;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- if you hit an object. Do not use your trimmer until you
are sure that the entire trimmer is in a safe operating
condition;
- if the trimmer starts to vibrate abnormally. Check im-
mediately. Excessive vibration can cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
trimmer is in safe working condition.
2. Replace worn or damaged parts for safety.
3. Only use the replacement cutting line specified for
this product.
4. Only use replacement parts and accessories recom-
mended by Husqvarna UK Ltd..
5. After any maintenance in dealing with the cutting line,
always return the product to its normal operating po-
sition before switching on.
6. To avoid the risk of injury keep fingers and hands
clear of the line cutter on the leading edge of the guard.
7. Inspect and maintain the trimmer regularly. Any re-
pairs must be carried out by an authorised repairer.
8. Store in a cool dry place and out of reach of children.
Do not store outdoors.
9. Allow the product to cool for at least 30 minutes be-
fore storing.
Cables
IMPORTANT
If you want to use an extension cable when operating your
product, only the following cable dimensions should be used.
- 1.0 mm2: max length 40m
- 1.5 mm2: max length 60m
- 2.5 mm2 : max length 100m
Minimum rating :
1.00mm2size cable, 10 amps 250 volts AC.
YOUR TRIMMER IS SUPPLIED WITH AN ELECTRIC
MAINSCABLE WIRED DIRECTLYINTO THEPRODUCT.
1. Mains Cables and Extension Cables are available from
your local Husqvarna UK Ltd. Approved Service Centre.
2. Do not wire an extension cable directly to your product
yourself. Please contact your local Husqvarna UK Ltd.
Approved Service Centre for further information on the
connectors and kits available.
3. Only use extension cables specifically designed for
outdoor use.
CONNECTORS
Our connectors are suitable for use with 2 core cable
only. Under no circumstances should these connectors
be used for earthed products.
All of our connectors and cables are of splashproof con-
struction. They are not waterproof and must not be left
outside permanently nor should they be submerged or
immersed in water. Do not let cable lay or trail through
pools of water or splashed with water from hose pipes.
MAINS PLUG REPLACEMENT
•If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is in-
serted into a 13 amp socket.
1. No earth required. Our products are double insulated
to EN60335 and under no circumstances should an
earth be connected to any part of the product.
2.Ensure the mains voltage suits your product.
3. IMPORTANT!
The wires in the mains lead are coloured in accordance
with the following code:
BLUE - NEUTRAL
BROWN - LIVE
The wire which is coloured BLUE must be connected to
the Terminal which is marked with the letter ‘N’ or
coloured BLACK. The wire which is coloured BROWN
must be connected to the Terminal which is marked with
the letter ‘L’ or coloured RED.
4. It is important that the outer sheath is clamped cor-
rectly into the 3-pin plug.
5. If in doubt consult your local Service Repairer or qual-
ified electrician before the machine is used.
6. A13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only pro-
tect the electrical equipment and are not a safeguard
against electrocution.
If your product is hard wired i.e. non-detachable mains
electric cable, a conversion kit and extension cable is
available from all Husqvarna UK Ltd. Approved Serv-
ice Centres which can be found in your local Yellow
Pages.

Assembly Instructions
Shaft Assembly (A)
1. Locate the lower shaft (A1) into the upper shaft (A2).
2. Grasp firmly and hold steady the lower shaft. Locate
the upper shaft and snap together firmly.
• The unit is correctly assembled when the gap be-
tween the upper and lower shaft has been closed.
Safety Guard Assembly (B1) & (B2)
1. Locate the safety guard over the cutting head. Ensure
the nylon line is fed through the hole in the safety
guard as illustrated in fig B1.
2. Push into location and turn safety guard in the direc-
tion illustrated in Fig B2, until a click is heard and the
safety guard is securely locked in position.
•ENSURE THE SAFETY GUARD IS SECURELY IN
PLACE BY AT T EMPTING TO TWIST GUARD.
Cable Restraint (C) & (D)
1. Form loop in mains cable and push the loop through
the slot as illustrated in picture (C).
2. To secure, position loop over the hook and pull the
cable back through the slot as illustrated in picture (D).
A
12
Starting and Stopping
1
2
C D
F
WARNING
Cutting head continues to rotate after the trimmer has
been switched off.
To start your trimmer
Squeeze the switch lever (F).
To stop your trimmer
Release the switch lever (F).
B2
B1
Double Auto Feed System
How the automatic line feed works (E)
1. When initially switching on the trimmer, a small length
of line is fed out.
2. A ‘clattering’ noise will be heard when the two nylon
lines hit the line cutter. DO NOT BE ALARMED this is
quite normal. After approximately 5 seconds the line
will be cut to the correct length and the noise will re-
duce as the motor reaches full speed.
•Make sure the motor is up to full speed before trim-
ming or edging.
3. If the noise of the nylon line being cut cannot be heard,
more line will need to be fed out.
4. To feed more line, it is first necessary to to allow the
motor to stop completely, then re-start, allowing the
motor to reach full speed.
5. Repeat step 4. until you hear the lines hitting against the
cutter. (Do not repeat this procedure more than 6 times)
6. If problems are experienced with the automatic line
feed refer to Fault Finding Chart.
E
line cutter

•WARNING
•The use of eye protection is recommended.
Do not lean over the trimmer whilst trimming or edging,
objects may be thrown by the cutting line.
Do not allow cutting head to rest on the ground.
Do not overload your trimmer.
Overloading can be avoided by making sure the motor
speed does not drop unduly.
DISCONNECT FROM THE MAINS ELECTRICITY
SUPPLY BEFOREATTEMPTING ANY MAINTE-
NANCE OR ADJUSTMENT.
•BEFORE USE
Make sure that both lines are fed out.
• Make sure motor is up to full speed before trimming or
edging.
How to trim
1. Cut with nylon line at an angle using the tip. See Fig G.
2. Swing trimmer in and out of the cutting area taking
small cuts (H)
3. Line is fed out automatically every time the trimmer
head stops rotating and returns to operating speed.
• Extra line can be fed out manually as described in Man-
ual line feed
How to edge
1. To convert to edging mode, depress the locking button
(J1) and twist head anti-clockwise (J2). An audible
"click" will confirm that the head is locked. Ensure the
button has returned to its original position.
2. Hold as illustrated in Fig F.
3. To start, squeeze the switch lever.
4. Rest the edger on the roller for extra stability and line
up the edge of the lawn with the two indicators on the
guard (K1). Edge in direction indicated in Fig K.
5. To return to trimming mode, depress the locking button
and twist head clockwise. An audible "click" will con-
firm that the head is locked. Ensure the button has re-
turned to its original position.
G
J
H
How to trim and edge
12
1
K
To manually feed the nylon line (M)
1. If required line can be fed out manually.
2. To operate, press and release manual line feed button,
whilst gently pulling on one of the lines until the line
reaches the line cutter.
3. When the required amount of line is fed out, gently pull on
the second line (there is no need to press the manual line
feed button again).
4. If the line extends past the line cutter, too much line has
been fed out.
5. If too much line is fed out, remove the spool cap and click
spool anti-clockwise until the line is at the desired length.
To remove spool cap
1. Press and hold in the two cap release latches. (N).
2. Pull cap away from the spoolholder. (N).
When refitting the spool cap
1. Keep all areas of the cap and spoolholder clean. Fail-
ure to do so may prevent the cap being securely lo-
cated in the spoolholder.
2. Replace the cap, pressing firmly DOWN towards the
spoolholder to ensure cap is fully located.
3. Check that the cap is correctly fitted by trying to re-
move it without depressing the two latches.
Always return the product to its normal operating position
before switching on.
Cutting Head
Manual line
feed button
Cap
Cap release
latch
Spool
Spoolholder
Eyelet
N
M

Fault Finding Chart (Automatic Line Feed only)
WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.
FAULT CHECK ACTION
Is the automatic line feed work-
ing? Manually feed out line.
Is the line fed out and visible?
Has line been removed from
cleat?
Remove cap and spool, free line
and re-fit spool and cap.
The line may be jammed on the
spool. Rewind line to remove
crossed loops. Check that line is in
correct section of spool.
Is the manual line feed working?
Has too much line been fed out? Rewind line.
Contact your local approved Serv-
ice Centre or Husqvarna UK Ltd.
Customer Service.
Is the line cutter missing from the
safety guard?
Contact Husqvarna UK Ltd. Customer Service
Telephone : [phone] UK 1800 882 350 ROI
No
No
No
Yes
Yes
LINE NOT FEEDING
OR
LINE TOO SHORT
OR
TRIMMER VIBRATES
CONTINUOUS
CLATTERING NOISE
LINE SNAPS CONTINUOUSLY
IF NONE OF THE ABOVE
OR IF FAULT PERSISTS
Has the motor reached full speed
before use?
No
Allow the motor to reach full speed
before use
Are you using the trimmer cor-
rectly?
?
Only use tip of nylon line to trim.
Is the line jamming on the spool?
Yes
Rewind the line on the spool, if
symptoms still persist, change
spool and line.
To r e place nylon line
For your convenience it is recommended you buy spool
and line complete. Nylon line only is also available. Both
are available from Husqvarna UK Ltd. stockists.
To fit spool and line complete:
1. Remove the cap.
2. Remove old spool.
3.
Place new spool into spoolholder with cut out areas of
the spool in line with eyelets as shown in figure P.
4. Release one line from cleat and feed line through eyelet
(P).
5. Repeat for second line.
•Ensure spool is fully located by gently rotating it during
fitment, whilst keeping the spoolholder steady.
7. Refit the cap.
To fit nylon line only:
•Remember! Your Trimmer is designed to use only nylon
line with a maximum diameter of 1.5mm. Use only gen-
uine Husqvarna UK Ltd. nylon line.
1. IMPORTANT - Always wind the line onto the upper sec-
tion of the spool first.
Take approximately 5 metres of line. Insert 15mm of line
into one of the holes in the upper section of the spool
(Q) and wind line in the direction of the arrows on the
top of the spool. Leave approximately 100mm of line
unwound and place into cleat as illustrated in figure Q1.
Repeat on lower section of spool.
2. Care should be taken to ensure that the line is neatly
coiled on the spool. Failure to do so will impair the effi-
ciency of the automatic line feed.
3. Then fit spool as described in ‘To fit spool and line com-
plete’, section above.
Cleat
Q1
Cutting Head Cont’
P
Q
Cut out area
of spool
Eyelet

Maintenance
•WARNING
Disconnect from the mains electricity supply, before at-
tempting any maintenance or adjustment. Cutting
head continues to rotate after the trimmer has been
switched off. Keep fingers and hands clear of the line
cutter on leading edge of guard.
Caring for your Product
After you have finished using your trimmer follow the
procedure below:
1. Disconnect from the mains electricity supply.
2. Never clean your trimmer with water, cleaning flu-
ids, or solvents, just remove debris with a suitable
tool, a soft brush or dry cloth.
3. Using a soft brush, clean around the inside of the
safety guard, the cutting head and the motor hous-
ing air vents. (Fig R, S).
4. Inspect the trimmer carefully, especially the parts
of the cutting head.
5. If your trimmer is damaged in any way contact your
local Husqvarna UK Ltd. approved service centre.
• Never use a damaged trimmer.
6. Wind cable carefully to avoid kinking.
7. Store in a cool, dry place and out of reach of children.
S
Service Recommendations
• Your product is uniquely identified by a silver and black product rating label.
• We strongly recommend that your product is serviced at least every twelve months, more often in a professional
application.
R
Environmental Information
• Awareness of the environment must be considered
when disposing of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal
information.
The symbol on the product or on its packaging indi-
cates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic
equipment.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the envi-
ronment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about recycling of this prod-
uct, please contact your local council office, your house-
hold waste disposal service or the shop where you
purchased the product.
Replacement Parts
Spool and Line
Reference no.: FLY021 Part no.: 513937190
If any part is found to be defective due to faulty manufac-
ture within the guarantee period, Husqvarna UK Ltd.,
through its Authorised Service Repairers will effect the
repair or replacement to the customer free of charge pro-
viding:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired,
taken apart or tampered with by any person not au-
thorised by Husqvarna UK Ltd..
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way dimin-
ishes the customers statutory rights.
Failures due to the following are not covered, therefore it is
important that you read the instructions contained in this
Operator's Manual and understand how to operate and
maintain your machine:
Failures not covered by guarantee
* Replacing Nylon Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accor-
dance with the instructions and recommendations
contained in this Operator's Manual.
* Machines used for hire are not covered by this guaran-
tee.
* The following items listed are considered as wearing
parts and their life is dependent on regular mainte-
nance and are, therefore not normally subject to a
valid warranty claim: Nylon Line, Spool and Line, Elec-
tric Mains Cable.
* Caution!
Husqvarna UK Ltd. does not accept liability under the
warranty for defects caused in whole or part, directly
or indirectly by the fitting of replacement parts or addi-
tional parts that are not either manufactured or ap-
proved by Husqvarna UK Ltd., or by the machine
having been modified in any way.
Guarantee & Guarantee Policy

5748707-02
EC Declaration of Conformity
Husqvarna AB, 561 82, Huskvarna, Sweden
Declare under our sole responsibility that the product(s);
Category............................Electric Lawn Trimmer
Type(s) ............................PWT23
Identification of Series.......See Product Rating Label
Year of construction ..........See Product Rating Label
Conforms to the essential requirements & provisions of the following EC Directives:
2006/42/EC, 2004/108/EC, 2000/14/EC
based on the following EU harmonized standards applied:
EN60335-1, EN60335-2-91, EN50366, EN55014-1, EN61000-3-2, EN61000-3-3
The maximum A weighted sound pressure level LpA at the operator’s position, measured
according to EN60335-2-91, corresponds to the Level given in the table.
The maximum hand / arm vibration weighted value measured according to EN ISO 20643 on
a sample of the above product(s) corresponds to the Value ahgiven in the table.
2000/14/EC: The Measured Sound Power LWA & Guaranteed Sound Power LWA values are
according to the tabulated figures.
Conformity Assessment Procedure............... Annex VI
Notified Body................................................. Intertek, Cleeve Road
Leatherhead, Surrey
KT22 7SB, England
Ulm 25/08/2011
P. Lameli
Global R & D Director - Hand held
Keeper of technical documentation
Ty pe
Width of Cut (cm)
Speed of Rotation of Cutting Device (rpm)
Power (kW)
Measured Sound Power LWA (dB(A))
Guaranteed Sound Power LWA (dB(A))
Level LpA (dB(A))
Uncertainty KpA(dB(A))
Value ah(m/s2)
Uncertainty Kah (m/s2)
Weight (Kg)
PWT23
23
9900
0.30
94
96
80
2.5
1.0
1.5
2.1
Our policy of continuous improvement means that the specification of products may be altered from time to time without
prior notice.
Copyright © 2011 Flymo S.A. All rights reserved. Flymo® and other product and feature names are registered or
unregistered trademarks of Flymo S.A.
Husqvarna AB
561 82 Huskvarna
Sweden