FMI C32GO Instruction manual

For more information, visit www.fmiproducts.com
C32GO Corner Mantel and Base
ASSEMBLY AND INSTALLATION INSTRUCTIONS
IMPORTANT: Read entire instruction sheet be-
fore assembling or installing mantel kit.
These mantels are only approved for use with
any FMI PRODUCTS, LLC 32'' electric and gas
replace systems. Do not use mantel with any
other product.
• Thismantelkitcontainsthefollowing:
#1Base
#2RightSideAssembly
#3LeftSideAssembly
#4Header
#5Top
#6TopTriangle
#7TopLeftSupport
#8TopRightSupport
#9TopCenterSupport
#10BaseSupport
#11VerticalSupport
RightTopTrimStrip
LeftTopTrimStrip
• HardwarePackage
36-11/4"WoodScrews114325-01
8-1"FinishingNails114295-04
4-2"WoodScrews122447-01
*Extrahardwaremaybeincluded
Toolsrequired:
• PowerScrewdriverwith#2PhillipsBit
• Hammer
• NailSet
Ifanywoodpiecesaremissingordamaged,contactthedealer
whereyoupurchasedthismantelforreplacement.Ifhardware
is missing or damaged, contact FMI PRODUCTS, LLC at
1-866-328-4537 for referral information. You can also visit
FMIPRODUCTS,LLC’swebsiteatwww.fmiproducts.com.
Note: Gather all mantel pieces together before assembling
mantel.
WARNING: Only use 1 1/4" screws to as-
semble mantel. Damage to mantel will result if
other screws are used for this purpose.

www.fmiproducts.com 123755-01B
2
ASSEMBLING MANTEL
IMPORTANT: More than one person is required
to lift assembled mantel. Lift mantel by leg
assemblies. Lifting by header or mantel top
could damage mantel.
Usethefollowingillustrationstoassemblemantel.Useonly
screwsprovided.
Figure 1 - Installing Base Support
Figure 3 - Installing Mantel Base
Figure 4 - Mantel Top Assembly
Figure 2 - Installing Header
1¼''Screws
BaseSupport#10
Base#1
IMPORTANT:Alignmantellefttorightonbasebeforeinstalling.
Cornerofmantellegsmustbeushwithbackofmantelbase
beforeinstallation(seeFigure6,page3).Useatapemeasure
toinsureaccuracy.
IMPORTANT:Use2"screwsonlyontopcentersupport.Using
2"screwsinanyotherlocationwilldamagemantel.
TopCenter
Support#9
MantelTop#5
TopLeft
Support#7 TopTriangle#6 TopRight
Support#8
2''Screws
1¼''Screws
Header#4
RightLeg
Assembly#2
LeftLeg
Assembly#3
1¼''Screws
Headerinto
GrooveonLegs
Header
Assembly
Block
LeftLeg
Assembly
#3
1¼''Screws
Base#1
RightLeg
Assembly
#2

www.fmiproducts.com
123755-01B 3
Figure 6 - Installing Mantel Top
Figure 7 - Installing Gas Fireplace
FIREPLACE INSTALLATION
1. Fireplace should be fully assembled. See Assembling
Fireplaceinreplaceowner’smanual.
2. Mantelmustbeinstalledushwithtwowalls.Remove
baseboardalongwallswheremantelistobeinstalled.
Baseboardwillpreventproperinstallationofmanteland
base.
3. Placemantelbaseclosetoinstallationlocation.Seere-
placeowner’smanualforinstallationclearances.Leave
enoughroomtoinsertreplacefrombackofmantel.
4. Ifinstallinggasreplace,installgasline.SeeConnecting
to Gas Supplyinreplaceowner’smanual.Rememberto
leaveaccesstogasshutoffvalvesomewhereonmantel
baseorwhereitisaccessibletouser.Checkforleaks.
See Checking Gas Connections in replace owner’s
manual.
5. Position replace inside mantel through back opening
(seeFigure7).Carefullypositiongaslinesifapplicable.
IMPORTANT:Usecautionwhenpositioningreplaceon
base.Basemayscratcheasily.Makesurereplaceisin
properpositionwithinmantelopeningbeforecontinuing
withinstallation.
6. Gas replace with louver door: Lower bottom louver
door.Usetwoscrewsprovidedinreplacehardwarekit
andattachreplacetowoodenbase.Closelouverdoor.
Gas replace with xed louver:Beforeinstallinglogs
orburnerassembly(seeowner’smanual)removescrews
securingoortoassembly.Liftoorforaccess to bot-
tomofreplace. Use twoscrews provided inreplace
hardwarekitandattachreplacebasetowoodenbase.
Reinstalloorwithscrewsremovedpreviously.
IMPORTANT:Alignmanteltoplefttorightbeforeinstalling.
Backcornerofmantellegmustbeushwithedgeofmantel
topbeforeinstallation.
IMPORTANT:Ifinstallingagasreplace,verticalsupportwill
beinstalledtomantelassemblyaftergasreplacehasbeen
installed.Ifinstallingelectricreplace,rstinstallverticalsup-
portandinstallreplacefromfrontofmantel.Donotputany
weightonmanteltopuntilverticalsupporthasbeeninstalled.
Figure 5 - Installing Heat Reector Strip
IMPORTANT: Make sure heat reector strip is ush against
header and spacers are on bottom side. Heat strip should
NOT be ush with leg side but should have 1" clearance on
both ends.
Header#4
HeatReector
Strip
1¼''Screws
MantelTop
Assembly
Assembly
Blocks
Assembly
Blocks
Corner
ofMantel
LegsMust
beFlush
withedge
ofMantel
Top
Mantel
LegsFlush
withMantel
Base
1¼''
Screws

123755-01
Rev.B
10/11
2701S.HarborBlvd.
SantaAna,CA92704
1-866-328-4537
www.fmiproducts.com
ELECTRIC FIREPLACE INSTALLATION
ThismantelcanbeusedwithFMIPRODUCTS,LLCelectric
replaces.Electricreplacesinstallfromthefrontofmantel.
Toinstallelectricreplaceseereplaceinstructionmanual.
Vertical Support Installation
Installverticalsupport(seeFigure8).
MANTEL INSTALLATION
1. Carefullypushmantelandbaseintopositionincorner
andushagainstbothwalls.Checkoperationofreplace
beforeproceeding.
2. Placerighttrimstriponrightsideoftopandlefttrimonleft
sideoftop.Alignbothpiecessoanygapsbetweenmantel
andwallarecoveredaswellaspossibleandfrontoftrim
stripsareushwithsideoftop.Withonepersonholding
trimstripsinplace,naileachstriptomantleusingnishing
nailsincludedinhardwarekitandnailset.
Figure 8 - Installing Vertical Support
Figure 9 - Installing Mantel Trim
FinishingNails
TrimStrips
BaseSupport#10
Vertical
Support
#11
1¼''Screws
1¼''Screws
Top
Center
Support