FMI PHK18 Quick start guide
For more information, visit www.desatech.com
WARNING: If the information in this manual is not
— WHAT TO DO IF YOU SMELL GAS
• Do not touch any electrical switch; do not use any
-
VENTED DECORATIVE NATURAL GAS LOG APPLIANCE
OWNER’S OPERATION AND INSTALLATION MANUAL
MODELS PHK18, PHK24, PHK30,
BCS18, BCS24 AND BCS30
RGA 2-72 Approved
TESTED AND
LISTED BY
-
www.desatech.com 115425-01E2
SAFETY
TABLE OF CONTENTS
Safety .................................................................. 2
Product Identication........................................... 4
Local Codes......................................................... 5
Unpacking............................................................ 5
Installation ........................................................... 5
Operation........................................................... 10
Cleaning and Maintenance................................ 10
Troubleshooting..................................................11
Technical Service............................................... 12
Service Hints ..................................................... 12
Replacement Parts............................................ 13
Accessories ....................................................... 13
Parts .................................................................. 14
Warranty ..............................................Back Cover
-
service or maintenance can
Refer to this manual for correct
additional information consult
is for installation only in a
material and connected to a
-
National
Fuel Gas Codes, ANSI Z233.1/
NFPA54,Air for Combustion and
Ventilation.
State of Massachusetts: The
chemicals known to the State
of California to cause cancer or
-
-
www.desatech.com
115425-01E 3
Early signs
of carbon monoxide poisoning resemble the
u, with headaches, dizziness or nausea. If
you have these signs, the log set may not
be working properly. Get fresh air at once!
Have log set serviced. Some people are
more affected by carbon monoxide than oth-
ers. These include pregnant women, people
with heart or lung disease or anemia, those
under the inuence of alcohol and those at
high altitudes.
Natural Gas: Natural gas is odorless. An
odor-making agent is added to the gas. The
odor helps you detect a gas leak. However,
the odor added to the gas can fade. Gas may
be present even though no odor exists.
Make certain you read and understand all
warnings. Keep this manual for reference. It
is your guide to safe and proper operation of
this log set.
-
WARNING: Do not allow fans
SAFETY
Continued
adults away from hot surface to
-
-
dren when they are in the room
1. This appliance, as supplied, is for use
with NATURAL GAS ONLY, as indicated
on rating plate. This appliance is NOT
convertible for use with propane/LP gas.
2. If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not
use any phone in your building
• immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions
• if you cannot reach your gas supplier,
call the re department
www.desatech.com 115425-01E4
3. Never install log set
• in a recreational vehicle
• where curtains, furniture, clothing, or
other ammable objects are less than
42" from the front, top, or sides of the
log set
• in high trafc areas
• in windy or drafty areas
• in bedroom or bathroom
4. Before installing in a solid fuel burning
replace, chimney ue and rebox must
be cleaned of soot, creosote, ashes and
loose paint by a qualied chimney cleaner.
Creosote will ignite if highly heated. Inspect
chimney ue for damage. If damaged,
repair ue before operating heater.
5. To reduce creation of soot, follow in-
structions in Cleaning and Maintenance,
page 10.
6. Installation and provisions for combus-
tion and ventilation air must conform
with the National Fuel Gas Code, ANSI
Z233.1/NFPA 54, Air for Combustion and
Ventilation.
SAFETY
Continued
PRODUCT IDENTIFICATION
Figure 1 - Product Identication (Ramp Pan Burner)
Grate
Burner Pan
Burner Inlet
(Under Pan)
7. Do not run log set
• where ammable liquids or vapors are
used or stored
• under dusty conditions
8. Do not burn solid fuel in replace after
installing log set. Do not use this log
set to cook food or burn paper or other
objects.
9. To help prevent breakage, new logs must
be broken in (see Curing Logs page 10).
10. Turn log set off and let cool before servic-
ing, installing, or repairing. Only a qualied
service person should install, service, or
repair log set.
11. Provide adequate clearances around air
openings.
Hearth Kit Model ________________
Serial Number __________________
Log Set Model __________________
www.desatech.com
115425-01E 5
LOCAL CODES
Install and use log set with care. Follow all
local codes. In the absence of local codes,
use the latest edition of the National Fuel Gas
Code ANSI Z223.1/NFPA 54*.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
INSTALLATION
UNPACKING
CAUTION: Do not remove
1. Remove logs, hearth kit, pan materials,
and hardware from carton.
2. Remove all protective packaging applied
to logs and base for shipment.
3. Check heater for any shipping damage.
If heater is damaged call DESA Heating,
LLC at 1-866-672-6040 for replacement
parts before returning to dealer.
-
-
NOTICE: Installation, service,
-
listed in these instructions may
-
this kit, or use of unauthorized
warranty, and may result in a
FLUE OPENING SPECIFICATIONS
Note: This vented appliance must be installed
only in a solid-fuel burning replace with a
working ue and constructed of noncombus-
tible material.
Charts in Figure 2, page 6, indicate technical
information regarding installation of your gas
log set. Please make sure all specications
shown are applicable before installation is
attempted.
Fireplace must include a working ue and
venting system with minimum openings
shown in Figure 2, page 6.
www.desatech.com 115425-01E6
into room, extinguish ame and remove any
obstruction until proper venting is achieved.
Chimney ue must remain open a minimum of
3" at all times during operation of log set.
INSTALLING DAMPER CLAMP
Secure damper stop clamp provided to
leading edge of damper as shown in Figure
3. If for any reason this clamp doesn't work
on your replace, another suitable clamp or
permanent stop must be installed, or damper
blade must be cut or removed.
For Massachusetts Residents Only: In-
stallation of this vented gas log set in the
Commonwealth of Massachusetts requires
damper be permanently removed or welded
in fully open position.
INSTALLATION
Continued
Figure 3 - Attaching Damper Clamp
Manufactured
Fireplace
Masonry
Fireplace
Damper Damper
Damper
Clamp
Damper Clamp
CONNECTING TO GAS SUPPLY
-
Installation Items Needed
Before installing log set, make sure you have
the items listed below.
• piping (check local codes)
• sealant (resistant to Propane/LP gas)
• equipment shutoff valve
• test gauge connection
• adjustable (crescent) wrench or pliers
• sediment trap
• tee joint
• pipe wrench
CHECK GAS TYPE
Use only natural gas. If your gas supply is
not natural gas, you MUST NOT install this
gas log set.
If replace does not have a gas supply shutoff
valve, one must be installed.
VENTING SPECIFICATIONS FOR
INSTALLATION
Fireplace chimney ue and vent must be draft-
ing properly. To check vent for proper draft-
ing: Light a tightly rolled newspaper on one
end and place inside front edge of replace.
Observe smoke and be sure vent is properly
drawing smoke up chimney. If smoke spills out
Model Burner
Minimum
Flue
PHK18
BCS18 18" Ramp 57,000 8"
PHK24
BCS24 24" Ramp 80,000 8"
PHK30
BCS30 30" Ramp 90,000 8"
Model Front
Width
Back
Width*
PHK18
BCS18 28" 18" 16" 18"
PHK24
BCS24 36" 23" 16" 18"
PHK30
BCS30 42" 29" 18" 18"
* At depth Indicated
Figure 2 - Technical Information Charts
Fuel Inlet Pressure
N.G. 5.5" 10.5"
Natural Gas
18" 0.120 31
24" 0.140 28
30" 0.1495 25
www.desatech.com
115425-01E 7
-
Installation must include an equipment shut-
off valve, union, and plugged 1/8" NPT tap.
Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from log
set (see Figure 4).
IMPORTANT: Install equipment shutoff valve
in an accessible location. An equipment shut-
off valve is for turning on or shutting off gas
to the appliance.
Apply pipe joint sealant lightly to male NPT
threads. This will prevent excess sealant from
going into pipe. Excess sealant in pipe could
result in a clogged burner injector.
Figure 4 - Gas Connection
3" Minimum
Sediment Trap
From Gas Meter
(5" W.C.** to
10.5" W.C.
Pressure)
CSA Design-Certied
Equipment Shutoff Valve
With 1/8" NPT Tap*
Approved Flexible Gas Hose
(if allowed by local codes)
Tee
Joint
Pipe
Nipple
Cap
* Purchase optional CSA design-certified
equipment shutoff valve from your dealer.
** Minimum inlet pressure for purpose of input
adjustment.
INSTALLATION
Continued
We recommend that you install a sediment
trap in supply line as shown in Figure 4.
Locate sediment trap where it is within reach
for cleaning. Install in piping system between
fuel supply and heater. Locate sediment trap
where trapped matter is not likely to freeze.
A sediment trap traps moisture and contami-
nants. This keeps them from going into log set
controls. If sediment trap is not installed or is
installed wrong, log set may not run properly.
CHECKING GAS CONNECTIONS
and connections, internal and
external to unit, for leaks after
WARNING: Never use an
-
PRESSURE TESTING GAS SUPPLY
PIPING SYSTEM
Test Pressures In Excess Of 1/2 PSIG
1. Disconnect log set and its individual equip-
ment shutoff valve from gas supply piping
system.
2. Cap off open end of gas pipe where equip-
ment shutoff valve was connected.
3. Pressurize supply piping system by either
using compressed air or opening main gas
valve located on or near gas meter.
4. Check all joints of gas supply piping system.
Apply noncorrosive leak detection uid to
gas joints. Bubbles forming show a leak.
5. Correct all leaks at once.
6. Reconnect log set and equipment shutoff
valve to gas supply. Check reconnected
ttings for leaks.
www.desatech.com 115425-01E8
INSTALLATION
Continued
Figure 6 - Checking Gas Joints
Gas Meter
Equipment
Shutoff Valve
HEARTH KIT ASSEMBLY AND
INSTALLATION
1. Determine which side gas line feeds into
replace. This log set is factory set up for
right side (facing) gas feed. If your gas line
is on the right side, go to Installation and
Gas Connection. If your gas line is on the
left side of replace, proceed with steps 2
through 4 below.
2. Remove nuts securing gas inlet venturi to
bottom of burner.
3. Remove venturi from pan taking care not to
damage gasket between venturi and pan.
4. Reverse direction of venturi and reattach
to bottom of pan using factory nuts.
Figure 7 - Venturi Gas Connection
Burner Orice
(Factory Installed)
Burner Inlet Venturi
(Attached to Pan
Bottom)
Gas Connector
Tube
Adapter
Fitting
Burner Inlet Fitting
(Factory Installed)
Installation and Gas Connection
1. Place ramp burner assembly in center
of replace oor. Make sure front of pan
faces forward.
2. Thread gas supply tting to replace gas
supply pipe. Use thread sealant.
3. Install gas connector tube to gas supply
tting. Carefully shape tube to attach to
adapter tting. Be careful not to cause
kinks in tube.
4. Attach opposite end of gas connector tube
to gas inlet tting on end of venturi.
1. Close equipment shutoff valve (see Fig-
ure 5).
2. Pressurize supply piping system by either
using compressed air or opening main gas
valve located on or near gas meter.
3. Check all joints from gas meter to equip-
ment shutoff valve (see Figure 6). Apply
noncorrosive leak detection uid to gas
joints. Bubbles forming show a leak.
4. Correct all leaks at once.
TESTING BURNER FOR LEAKS
1. Generously apply noncorrosive leak
detection uid to all connections.
WARNING: Never check for
2. Light burner with shutoff valve no more
than half open and holding a match
slightly in front of pan (see Lighting In-
structions, page 10).
3. Inspect all connections for bubbles, raw
gas odor, or ame from any area other than
burner (leaks). If leaks are detected, shut
off gas valve immediately. Tighten, or reas-
semble loose connection(s) using pipe joint
compound until burner system is leak free.
4. When burner is tested and leak free, ob-
serve individual tongues of ame on burner.
Make sure all ports are clear and producing
ame evenly across burner. If any ports
appear blocked, clear by removing burner
manifold and reaming ports with a modied
paper clip or other suitable tool.
5. When nished testing, turn gas shutoff
valve OFF to extinguish all ames.
Figure 5 - Equipment Shutoff Valve
Open
Closed
Equipment
Shutoff
Valve
www.desatech.com
115425-01E 9
INSTALLATION
Continued
ADDING PAN MATERIAL
1. Open bag of glowing embers and spread
it evenly over burner ramp.
2. Open small bag of platinum embers and
place randomly throughout ember bed;
more heavily near front of ramp.
INSTALLING THE GRATE AND LOGS
1. Place grate over burner pan where two
outer horizontal supports on grate t into
two pan positioning tabs on outer edges
of pan.
2. Place large back log on grate at top tier
(rear) of ramp (see Figure 8).
3. Figures 8 and 9 show a suggested log
arrangement, however you may arrange
logs as you wish. Leave as much open
space between logs as possible to mini-
mize ame impingement and sooting.
Note: Logs may chip if they are handled
roughly or if hit together while being
placed.
Figure 8 - Installing Logs and Grate
Figure 9 - Suggested Log Arrangement
www.desatech.com 115425-01E10
OPERATION
3. Wait ve (5) minutes to clear out any gas.
If you then smell gas STOP! Follow the
safety information, column 1. If you don't
smell gas, go on to the next step.
4. Light a match and lay it on top of pan
material about 2" from the end of supply
side of pan
5. Slowly turn gas shutoff valve ON until
burner ignites. If burner doesn’t ignite
within 10 seconds with match burning,
turn shutoff valve OFF and repeat steps
1 through 4.
GAS SHUTOFF
VALVE OPERATION
Adjust the ame ON/OFF by turning gas shut-
off valve counterclockwise to open or
clockwise to close, as necessary.
Turn gas shutoff valve clockwise to
the OFF position (see Figure 5, page 8) .
CURING
LOGS
During the 2-3 hour appliance break-in period,
you may detect an odor from the appliance
as the various paints and compounds used in
the manufacturing of this log set cure. This is
a normal and temporary situation that is not
cause for alarm. However, you may want to
provide extra ventilation to the room during
this time.
CLEANING AND MAINTENANCE
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not fol-
low these instructions exactly,
-
-
WHAT TO DO IF YOU SMELL GAS
• Do not touch any electric switch; do not
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information,
above.
2. Turn gas shutoff valve to OFF.
• Keep the area around log set clean and
clear of debris.
• Occasionally, you may use a soft bristle
brush to clean logs.
• Once every year a qualied agency or
certied chimney sweep should examine
and clean the venting system of replace.
www.desatech.com
115425-01E 11
TROUBLESHOOTING
Note: All troubleshooting items are listed in order of operation.
OBSERVED PROBLEM
Log set is smoking/sooting
excessively
(Note: It is natural and unavoid-
able for vented gas log sets to
produce moderate levels of
carbon (soot) where ames
contact the logs. This is es-
pecially true with propane/LP
gas.)
Burner is excessively noisy
(Note: The movement and
combustion of gas will cre-
ate low, unavoidable levels
of noise.)
Burner ame is too low or
too high
POSSIBLE CAUSE
1. Poor fuel quality
2. Fireplace venting system
not drafting properly
3. Excessive ame impinge-
ment or blockage
4. Improper fuel/air mixture
5. Excessive gas supply/
pressure
1. Passage of air/gas across
irregular surfaces
1. Incorrect gas supply or
pressure
2. Blocked burner orice or
burner manifold ports
3. Improper burner orifice
size
REMEDY
1. Contact local natural or
propane/LP gas company
2. Adjust damper wide open
and/or have replace and
venting professionally
cleaned and checked
3. Separate the logs to allow
more ame passage
4. Remove any foreign items
from the ame pattern and/
or check for proper orice
sizing
5. Preheat flue in very cold
weather
1. Relieve any tight bends or
kinks in gas supply line
1. Check for proper gas sup-
ply pressure
2. Free burner orifice and
manifold ports of any burrs,
paint, or other blockage
3. Verify proper burner ori-
fice sizing (see Figure 2,
page 6)
www.desatech.com 115425-01E12
TROUBLESHOOTING
Continued
-
IMPORTANT: Operating log set where impurities in air exist may create odors. Cleaning sup-
plies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc.,
create fumes. These fumes may mix with combustion air and create odors. These odors will
disappear over time.
POSSIBLE CAUSE
1. Metal expanding while
heating or contracting
while cooling
1. Log set burning vapors
from paint, hair spray,
glues, cleaners, chemi-
cals, new carpet, etc. (See
IMPORTANT statement
above)
2. Gas leak. See Warn-
1. Gas leak. See Warn-
2. Control valve defective
1. Gas leak. See Warn-
OBSERVED PROBLEM
Log set produces a clicking/
ticking noise just after burner
is lit or shut off
Log set produces unwanted
odors
Gas odor even when control
knob is in OFF position
Gas odor during combustion
REMEDY
1. This is normal with most log
sets. If noise is excessive,
contact qualified service
person
1. Open flue to maximum.
Stop using odor causing
products while log set is
running
2. Locate and correct all leaks
(see Checking Gas Con-
nections, page 7)
1. Locate and correct all leaks
(see Checking Gas Con-
nections, page 7)
2. Replace control valve
1. Locate and correct all leaks
(see Checking Gas Con-
nections, page 7)
TECHNICAL SERVICE
You may have further questions about installa-
tion, operation, or troubleshooting. If so, con-
tact DESA Heating, LLC at 1-866-672-6040.
When calling please have your model and
serial numbers of your heater ready.
You can also visit DESA Heating, LLC’s web
site at .
SERVICE HINTS
When Gas Pressure is Too Low
• pilot will not stay lit
• burners will have delayed ignition
• heater will not produce specied heat
• propane/LP gas supply may be low
You may feel your gas pressure is too low. If
so, contact your local propane/LP or natural
gas supplier.
www.desatech.com
115425-01E 13
REPLACEMENT PARTS
Note: Use only original replacement parts.
This will protect your warranty coverage for
parts replaced under warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
call DESA Heating, LLC at 1-866-672-6040.
When calling DESA Heating, LLC, have
ready:
• your name
• your address
• model and serial numbers of your heater
• how heater was malfunctioning
• purchase date
Usually, we will ask you to return the part to
the factory.
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this product. If
they can’t supply original replacement part(s),
call DESA Heating, LLC at 1-866-672-6040 for
referral information. A list of authorized dealers
can be found by visiting
When calling DESA Heating, LLC, have
ready:
• model and serial numbers of your heater
• the replacement part number
ACCESSORIES
Purchase these accessories from your local
dealer. If they can not supply these accessories
call DESA Heating, LLC at 1-866-672-6040 for
information. You can also write to the address
listed on the back page of this manual.
For decorative purposes only. Not to be used
as additional logs on unit.
For decorative purposes only. Not to be used
as additional logs on unit.
Use for additional decoration
only. (3 pine cones per box).
For all models. Use for rebox decoration
only.
Use for rebox decoration
only.
Use for rebox decoration
only.
Use for rebox decoration
only.
DECORATIVE ASH BED CONTROL
COVER - CDABKA
An attractive way to cover
control knob and piezo ignitor.
Additional decoration
for front grate.
Additional decoration
for front grate.
Additional decoration
for front grate.
Creates the sound of a real
burning re.
www.desatech.com 115425-01E14
PARTS
1
8
23
17
10
18
11
13
24
9
3
2
4
5
6
7
22
15
16
20
12
21
19
14
www.desatech.com
115425-01E 15
PARTS
This list contains replaceable parts used in your log set. When ordering parts, follow the
instructions listed under Replacement Parts on page 13 of this manual.
KEY
PART NODESCRIPTION QTY
1 901059-01 3/8 FLR x 1/2 FPT Elbow • • • 1
2 901056-01 3/8 FLR x 3/8 FPT Adaptor • • • 1
3 101628-01 Gas Line - 10' Flex • • • 1
4 104506-27 Natural Gas Injector • 1
104506-28 Natural Gas Injector • 1
104506-29 Natural Gas Injector • 1
5 14538 Venturi • • • 1
6 14527 Venturi Gasket • • • 1
7 115482-01 Burner Pan • 1
115482-02 Burner Pan • 1
115482-03 Burner Pan • 1
8 901242-01 Damper Clamp Assembly • • • 1
9 11209 Nut #10/24 • • • 2
10 114986-01 Log Grate • 1
114986-02 Log Grate • 1
114986-03 Log Grate • 1
11 901481-01 Bottom Log • 1
109128-02 Bottom Log • 1
109128-01 Bottom Log • 1
12 111827.08 Small Log • 1
13 112489-01 Small Log • • 1
14 109399-01 Small Log • • • 1
15 115421-02 Small Log • • • 1
16 111960-01 Small Log • • 1
17 111929-01 Top Log • • • 1
18 109130-01 Top Log • • 1
19 112488-01 Top Log • • • 1
20 111962-01 Top Log • • • 1
21 111930-01 Small Log • 1
22 109405-01 Small Log • • • 1
23 115421-01 Small Log • • 1
24 112363-05 Small Log • • 1
PHK/BCS 18
PHK/BCS 24
115425-01
Rev. E
05/08
115425 01
NOT A UPC
DESA Heating, LLC
2701 Industrial Drive
Bowling Green, KY 42101
www.desatech.com
1-866-672-6040
WARRANTY
KEEP THIS WARRANTY
DESA HEATING, LLC LIMITED WARRANTIES
New Products
Standard Warranty: DESA Heating, LLC warrants this new product and any parts thereof to be free from
defects in material and workmanship for a period of four (4) years from the date of rst purchase from an
authorized dealer provided the product has been installed, maintained and operated in accordance with
DESA Heating, LLC’s warnings and instructions. When installed in a listed outdoor solid fuel burning re-
place, the warranty is limited to one (1) year for the burner system and logs.
For products purchased for commercial, industrial or rental usage, this warranty is limited to 90 days from
the date of rst purchase.
Factory Reconditioned Products
Limited Warranty: DESA Heating, LLC warrants factory reconditioned products and any parts thereof
to be free from defects in material and workmanship for 30 days from the date of rst purchase from an
authorized dealer provided the product has been installed, maintained and operated in accordance with
DESA Heating, LLC’s warnings and instructions.
Terms Common to All Warranties
The following terms apply to all of the above warranties:
Always specify model number and serial number when contacting the manufacturer. To make a claim under
this warranty the bill of sale or other proof of purchase must be presented.
This warranty is extended only to the original retail purchaser when purchased from an authorized dealer,
and only when installed by a qualied installer in accordance with all local codes and instructions furnished
with this product.
This warranty covers the cost of part(s) required to restore this product to proper operating condition and
an allowance for labor when provided by a DESA Heating, LLC Authorized Service Center or a provider
approved by DESA Heating, LLC. Warranty parts must be obtained through authorized dealers of this prod-
uct and/or DESA Heating, LLC who will provide original factory replacement parts. Failure to use original
factory replacement parts voids this warranty.
Travel, handling, transportation, diagnostic, material, labor and incidental costs associated with warranty
repairs, unless expressly covered by this warranty, are not reimbursable under this warranty and are the
responsibility of the owner.
Excluded from this warranty are products or parts that fail or become damaged due to misuse, accidents,
improper installation, lack of proper maintenance, tampering, or alteration(s).
This is DESA Heating, LLC’s exclusive warranty, and to the full extent allowed by law; this express warranty
excludes any and all other warranties, express or implied, written or verbal and limits the duration of any
and all implied warranties, including warranties of merchantability and tness for a particular purpose to four
(4) years on new products and 30 days on factory reconditioned products from the date of rst purchase.
DESA Heating, LLC makes no other warranties regarding this product.
DESA Heating, LLC’s liability is limited to the purchase price of the product, and DESA Heating, LLC shall
not be liable for any other damages whatsoever under any circumstances including indirect, incidental, or
consequential damages.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
For information about this warranty contact:
Model (
located on product or identication tag
) _____________________________
Serial No. (
located on product or identication tag
) __________________________
Date Purchased __________________________
Keep receipt for warranty verication.
This manual suits for next models
5
Table of contents
Other FMI Indoor Fireplace manuals
FMI
FMI (V)CB36N(E) User manual
FMI
FMI FSDVBNC Quick start guide
FMI
FMI (V)KC36NE series Quick start guide
FMI
FMI VT32N-A Quick start guide
FMI
FMI Natural Gas Burner System SDVBND Quick start guide
FMI
FMI FMH26TN 14 Operation manual
FMI
FMI (V)GL36CR(E) Quick start guide
FMI
FMI MF42INF Quick start guide
FMI
FMI Baja II 36WIL User manual
FMI
FMI CCAT36 Series Quick start guide
FMI
FMI GL36PN Quick start guide
FMI
FMI VVC42N Quick start guide
FMI
FMI CGEF23B Original instructions
FMI
FMI F48H(I)(R)A Quick start guide
FMI
FMI VC36N Quick start guide
FMI
FMI VT32N-A Quick start guide
FMI
FMI (V)VC42NE series Quick start guide
FMI
FMI FEF18 User manual
FMI
FMI VLDV43NE Quick start guide
FMI
FMI Masonry MM33 User manual
Popular Indoor Fireplace manuals by other brands
FireFriend
FireFriend DF-6500JU user manual
Riello
Riello 40 G20 Installation, use and maintenance instructions
Harrie Leenders
Harrie Leenders HL2 Instructions for installation, use and maintenance
HearthStone
HearthStone TUCSON owner's manual
Superior Fireplaces
Superior Fireplaces VRT3132WS Assembly, installation and operation instructions
Monessen Hearth
Monessen Hearth Direct Vent HDV500 Brochure & specs
FireplaceXtrordinair
FireplaceXtrordinair 98501001 Installation and owner's manual
KEDDY
KEDDY SK1000 Instalation instructions
Regency
Regency U32-NG5 Owners & installation manual
Town & Country Fireplaces
Town & Country Fireplaces TCWS54 SERIES D Installation and operating instructions
Travis Industries
Travis Industries 864 HO NB GSR2 installation manual
RAIS
RAIS VISIO 4 Series installation manual
Regency
Regency P33E-NG4 Owners & installation manual
Dimplex
Dimplex BLF50 Service manual
Regency
Regency P36-NG4 Owners & installation manual
Amantii
Amantii E 50 Fix Manual
Napoleon
Napoleon GDIZC - N Installation and operation instructions
Lennox Hearth Products
Lennox Hearth Products VISION Elite Series Brochure & specs