Focal Point NERO CUBE LCD Assembly Instructions

INSTALLATION & USER INSTRUCTIONS
All instructions must be handed to the user for
safekeeping.
MODELS COVERED BY THESE INSTRUCTIONS
NERO CUBE LCD ELECTRIC COMPLETE SUITE IVORY- F500336
NERO CUBE LCD ELECTRIC COMPLETE SUITE OAK- F500337
Focal Point Fires plc.
Christchurch, Dorset BH23 2BT
Tel: [phone]
Fax: [phone]
www.focalpointfires.co.uk
e : [e-mail]
FLOOR MOUNTED ELECTRIC FIRE
Please note : Except where otherwise stated, all rights,
including copyright in the text, images and layout of this
booklet is owned by Focal Point Fires plc. You are not per-
mitted to copy or adapt any of the content without the
prior written permission of Focal Point Fires plc.
1
Revision A- 03/11
©2011 Focal Point Fires plc.
GB IE
NERO
In the event of a problem with
this product, please call our
Customer Care Helpline.
01202 588 601

The Nero LCD electric heater provides convected heating in conjunction with a LCD screen which can display a number of different fuel effects
and scenes.The appliance is designed for indoor use, and can be simply floor mounted in the majority of floor positions anticipated. It can be
located in any household room, with the exception of bathrooms. Read all of the instructions before commencing installation. Retain for future
reference and pass on as necessary to subsequent owners of the appliance.
• DO NOT use this appliance immediately below a fixed socket outlet.
• DO NOT use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area where water/moisture could present a
hazard.
• CAUTION: This appliance must not be used in conjunction with any timer, programmer or thermal control, or any other device that will
switch on the appliance automatically, as a fire risk may occur if the heaters are accidentally covered or displaced.
•WARNING : This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are
occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
Do not allow the heater to be covered as this may cause overheating.The appliance must not be placed near curtains or similar material. A
clearance space of at least one metre should be allowed in front of the appliance.
The electrical socket that the appliance uses MUST be easily accessible. Do not route the supply cord directly over or above the heater unit. If
the cord is damaged, it must be replaced by a service agent or competent person.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
The LCD displays are produced using highly accurate technology, however, black pixels may be found, or red, blue and green pixels may not disap-
pear. This is perfectly normal and within product specification.This should not be regarded as a fault.
The appliance is designed to be floor mounted only. DO NOT RECESS ANY PART OF THE APPLIANCE.
The appliance is supplied with a pre-wired three pin BS1363 plug (13 Amp fuse rated), and 2 metre cable.A standard switched outlet/wall sock-
et, (including earth provision), must therefore be located within this distance, and be easily accessible in order to isolate the supply for mainte-
nance and cleaning. This socket must not be mounted behind or above the appliance.
IMPORTANT:THIS APPLIANCE MUST BE EARTHED.
The appliances are designed to be floor mounted. It is not necessary to secure the surround to the wall, provided it is sited on a firm level sur-
face.
It should be noted that the appliance creates warm convected air currents.These currents move heat from the room surroundings to, and up
the wall surfaces adjacent to the heater.
Operating the heater where impurities in the air, (such as tobacco smoke) exist, may slightly discolour wall finishing. Once the suite is in the
desired location check that it is level and it sits firmly on the floor, i.e. does not rock in any direction, and fits squarely against the wall.
Note: Skirting boards may need to be cut in order to fit the rear of the suite snugly against the wall, Provision must be made in the wall, either
behind the suite, or in one of the sides of the suite to allow the power supply cable to exit.
1.0 PRELIMINARY NOTES
INSTALLATION & USER INSTRUCTIONS
©2011 Focal Point Fires plc.
2
GB IE
©2011 Focal Point Fires plc.
2.0 APPLIANCE DATA
3.0 ELECTRICAL INSTALLATION REQUIREMENTS
4.0 SITE REQUIREMENTS
Weight (kg): 37.5 kg
Dimensions (mm): H 855 x W 850 x D 235
Voltage (Volts): 230-240V a.c. 50Hz
Heating Elements: 2 x 900/1000 Watts
Supply Cord: 2 metres
Supply Plug: BS 1363, 13A Fused
Location: Indoor Use
LCD Display: 40 Watts
Section Contents Page No.
1.0 Preliminary Notes 2
2.0 Appliance Data 2
3.0 Electrical Installation Requirements 2
4.0 Site Requirements 2
5.0 Clearances to Combustible Materials 3
6.0 Unpacking the Appliance 3
Section Contents Page No.
7.0 Component Checklist 3
8.0 Operating the Appliance 3
9.0 Safety Cut-Out System 5
10.0 Cleaning and Maintenance 5
11.0 Servicing 5
12.0 Appliance Dimensions 6

DO NOT -mount on a wall.
-recess any part of the appliance into the wall.
- site in a position where curtains or drapes could cover the appliance.
-site in a position where other soft materials could cover e.g. below a coat rack.
-site behind an opening door where mechanical impact/damage could occur.
-site where the supply cable would become a trip hazard.
-sit, stand or forcefully pull on the appliance.
-obstruct, cover or force items into the openings.
-use the heater to dry clothes.
- site/use in an outdoor location(s).
-run the supply cable under carpets.
It is important that the following clearances are maintained from the appliance to combustible materials and are dependant on the desired
mounting location as defined below.
This appliance is designed to be floor mounted only.
The minimum distance from the top of the appliance to a ceiling is 500mm.
The minimum distance to the sides of the appliance is 100mm.
The minimum distance to the front of the applaince is 500mm.
A shelf of any size or design may me mounted above the appliance.
Caution:This appliance is heavy.Always seek assistance whilst unpacking and/or during installation.
Read all the instructions before continuing to unpack or install this appliance. Carefully remove the appliance from its packaging. Check that
the remaining packaging contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling
centre.
QUANTITY DESCRIPTION
1 Fire suite
1 Remote control handset
1 Mains supply cord
1 Instruction Booklet
Read All Instructions Before Use
Check that the heater outlet grille, mounted at the top of the appliance, is not covered or obstructed in anyway, and ensure the power to the
fire is switched on.The power to the LCD display panel and the heater functions are controlled using four switches mounted underneath the
opening at the right hand side.
Controlling the heater functions
The first switch towards the top, marked (0I), controls the main power to the appliance and switches on the LCD display panel.This feature
can be used independently of the heating features.
The next switch down, marked (*) operates the fan blower without heat, and can be used for cool air circulation. However for this feature,
the main power switch (0I), must also be in the “on” position.
The next switch down, with a “single bar” marked (I) operates the low heat, (1kW), setting.
The switch at the bottom, with “two single bars” marked (II), operates the high heat, (2kW) setting.
To operate the fire in any of the above modes, the top switch marked (OI) must be switched to the “on” position.
To operate the fire, the (OI) switch must be on, followed by the (*)switch to start the blower.To obtain heat from the appliance, the
blower must be on and the I switch must then be operated for LOW heat, followed by the II switch for the HIGH heat setting.
4.0 SITE REQUIREMENTS - CONTINUED
5.0 CLEARANCES TO COMBUSTIBLE MATERIALS
GB IE
6.0 UNPACKING THE APPLIANCE
©2011 Focal Point Fires plc.
3
7.0 COMPONENT CHECKLIST
8.0 OPERATING THE APPLIANCE

Controlling the LCD display
panel - Basic functions
The LCD display may be switched
on and off indepenently of the
heater functions by using the
LCD on/off button as shown in
figure 10.
The appliance is pre-programmed
with nine different scenes as
shown in figures 1 through 9.
These scenes have been specially
edited to run in a seamless loop.
When the appliance is switched
on, the log fire scene will auto-
matically run.To select a different
scene either press the
button or the button. This will skip through all of the different
scenes in order.
Alternatively, to jump directly to a certain scene press one of the scene
select buttons. For example, button will play the log fire scene (see
figure 1). Button will play the twig fire scene (see figure 2) and so
on.
Certain scenes also include sound.This can be muted by pressing the
button.The volume can be lowered by pressing the button
and raised by pressing the button.
During normal operation the footage may occasionally be seen to ‘freeze’
for a fraction of a second.This happens as the scene is recycled to loop
again.This is perfectly normal and should be no cause for concern.
Controlling the LCD display panel - Advanced functions
The LCD display panels are factory set for best all-round performance
and no further adjustment should be necessary. Should you wish how-
ever, certain settings can be changed by using some of the buttons on
the handset and the on-screen menu systems.
8.0 OPERATING THE APPLIANCE- CONTINUED GB IE
4
©2011 Focal Point Fires plc.
Fig. 7 - Abstract scene Fig. 8 - Nature scene Fig. 9 - Aquarium scene
Fig. 4 - Gas fire (medium) Fig. 5 - Gas fire (high) Fig. 6 - Gas fire (Blue Flame)
Fig. 1 - Log fire Fig. 2 - Twig fire Fig. 3 - Coal fire
Figure 10 - Handset basic functions
Previous scene
Next scene
Mute
Standby/ON
Scene select
Volume lower
Volume raise
To access the display set-
tings menu press the
button on the handset.
The menu will appear
with the blue cursor on
the top right icon (figure
11).
Fig. 11
Press the or
button to move the blue
cursor over the icons. In
this example the bright-
ness menu has been
selected (figure 12).
Fig. 12

This appliance has a safety cut-out system fitted which will activate if the air inlets or heater outlets are obstructed. For safety reasons the fire
WILL NOT switch on again automatically. NOTE: The LCD display panel will remain operational if the cut-out is activated, only the fan heater
elements are prevented from operating.
The following procedure must be carried out before the fire can be operated again:
1. Unplug the power supply cable at the outlet socket and place all switches to off at the appliance.
2. Leave the fire OFF for a period of not less than 10 minutes, ensuring any obstructions are removed.
3. Plug in the power supply cable at the outlet socket, and then switch on at the appliance.
If an attempt to switch on is made before the safety cut-out has reset, the heaters may cut-out for a further period of time. If the sequence has
been followed correctly and the heaters still fail to function, check the power supply cable plug is plugged in at the outlet socket. If this is not
the cause, call an electrician.
ALWAYS DISCONNECT THE APPLIANCE AT THE SUPPLY OUTLET SOCKET BEFORE UNDERTAKING ANY CLEANING.
Except for periodic cleaning of dust, there are no specific requirements for care, other than regular cleaning of the general appliance. A wipe
with a dry cloth is normally sufficient. DO NOT use abrasive cleaners as they can damage the finish. Make sure the heater outlet grille (locat-
ed next to the switches), and the air inlet mesh grilles (located either side of the outlet grille) are kept clear of dust, pet hair and other airborne
household matter. These should be vacuum cleaned periodically using a brush attachment.
PLASTIC SCREEN - This should only be cleaned using a suitable glass cleaner.Test on a small area first.
There are no internal user serviceable parts.
Check security of supply cable and connections. If the supply cable becomes damaged, it must be replaced by a service agent or competent per-
son, such as a qualified electrician.
The wires in the cable are coloured in accordance with the following code:
LIVE - Brown
NEUTRAL - Blue
EARTH - Green/Yellow
Refer to Section 2.0,Appliance Data for fuse specification. Excluding fuses, use only genuine manufacturers spare parts available from your sup-
plier.
8.0 OPERATING THE APPLIANCE- CONTINUED GB IE
To change the value of
the selected menu item
press the button.The
value next to that item
will change colour to red.
(figure 13).
Fig. 13
Press the or
button to change the
selected value (figure
14). When you have fin-
ished, move the yellow
bar to ‘Return’ and press
the button.
Fig. 14
Finally, to exit this menu
system, move the blue
cursor to the ‘exit’ sym-
bol at the top right of
the menu, press the
button twice (figure
15).
Fig. 15
The appliance can be switched off at any time, irrespec-
tive of the particular mode selected, by simply switching
the first switch marked (OI) to the “off” position. It is also
recommended to unplug the power supply cable at the
supply outlet when not in use.
9.0 SAFETY CUT-OUT SYSTEM
10.0 CLEANING AND MAINTENANCE
5©2011 Focal Point Fires plc.
11.0 SERVICING

As our policy is one of continuous improvement and development, we therefore hope that you will understand we must retain the right to amend details and/or specifica-
tions without prior notice.
6©2011 Focal Point Fires plc.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.Check with your local authority or retailer for recycling advice.
F861027
12.0 APPLIANCE DIMENSIONS
235
850
850
5.2
566
565
Figure 16
All dimensions in mm.
GB IE