Focal Point Rivenhall DS-EHS01-41E Assembly Instructions

Focal Point Fires Ltd.
RBK House, Irishtown, Athlone,
Co. Westmeath, N37 XP52, Ireland
Tel: [phone]
Fax: [phone]
www.focalpointfires.co.uk
e: [email protected]
Revision B-11/21
Rivenhall White - DS-EHS01-41E
Rivenhall Black - DS-EHS01-39E
WALL MOUNTED OR FLOOR MOUNTED LED ELECTRIC FIRE
2021
MODELS SHOWN: RIVENHALL LED ELECTRIC SUITE

2021
7
8
9
9
10
10
10
11

2021
24 kg
H600x W1000 x D265(mm)
1.80
RIVENHALL WHITE - DS-EHS01-41E
RIVENHALL BLACK - DS-EHS01-39E

2021
Recess any part of the appliance into the wall, or run the supply cable under carpets
Site in a position where curtains or drapes could cover the appliance , or other soft materials could cover e.g. below a
coat rack
Site behind an opening door where mechanical impact/damage could occur
Site where the supply cable would become a trip hazard
Sit,stand or forcefully pull on the appliance
Obstruct,cover of force items into the openings
It should be noted that the appliance creates warm convected air currents. These currents move heat from the room
surroundings to, and up the wall surfaces adjacent to the heater.
Installing the heater next to these types of wall coverings or operating the heater where impurities in the air ,(such as
tobacco smoke) exist, may slightly discolour wall finishing.
If the appliance is to be secure on a dry lined or timber framed construction then the integrity and ability of the wall
to secure the appliance must be confirmed. It is important in these circumstances that any vapour barrier and or
structural members of the house frame are not damaged.
If you are unsure of the ability of the wall to secure the appliance and or which type of wall fixing to use, you should
take professional advice and obtain the correct fixings. Alternatively , find a more suitable wall location.
DO NOT
1 Heater unit
2 L shape brackets
1 Long bracket
7 Wall fixing screws
7 Wall plugs
2 Firebox screws
0.0003

2021

2021
A 4x30mm x 7pcs
C 4x12mm x 2pcs
B 6mm x 7pcs
B
C
A
568
400 1. Ensure the wall fixing brackets are level.
2. Mark out the 7 hole locations.
3. Drill 7 holes (6mm diameter, 40mm
deep) into the wall.
Please refer to the diagram for hole
locations.
For wall mounted installations
Please note: Before drilling into walls,
always check that there are no hidden
wires, pipes, etc.Make sure that screws
and wall plugs supplied are suitable for
supporting the unit in your surface.
Consult a qualified person if you are not
sure.
Insert the supplied wall plugs (B) into the
drilled holes.
Offer the brackets into position and screw
into place with the wall screws (A) provided.
Carefully lift the appliance onto the top
bracket.
Screw the 2 appliance screws (C) into
position underneath the appliance, securing
the appliance in place.
4.
5.
6.
7.
For floor mounted installations
Please note: Before drilling into walls,
always check that there are no hidden
wires, pipes, etc.Make sure that screws
and wall plugs supplied are suitable for
supporting the unit in your surface.
Consult a qualified person if you are
not sure.
Offer the appliance up to the wall in it's
desired location.
Draw a mark where you wish to connect
the strap to the wall.
1.
2.

2021
5. Flame effect
6. Fire ON/OFF
7. Power Switch
DOWN
LIGHT
NOTE: press
1.Mantel
2.Logs
3.Remote control
4.Heat settings 8. LED Downlights
button (5) 3 seconds to turn on the downlights function.
8.
7
Remove the appliance from the position and
drill a 1x hole (6mm diameter, 40mm deep)
3.
Gently hammer the wall plug into position.
4.
Carefully lift the appliance back into position.
5.
Using a screwdriver, screw through the fixing
strap and into the wall plug you have just
installed into the wall. Securing the appliance
into place.
6.

2021
DOWN
LIGHT
LED Display
Up Selection
Down Selection
Open Window/Door detection
Heat II
Heat I
“-” Selection“+” Selection
Downlights
Flame Effect
Timer ON/OFF
Power ON/OFF
Timer Set
Date Time Setting
Clear button
127( Before using any operation with the remote control, Insert 2 x AAA batteries to the back of the remote control.
The remote control will not respond until the digital display is illuminated as it is in sleep mode.Before operating ,
press any button once to illuminate the digital display in order to activate the remote control.
Do not press the remote control buttons more than once within two seconds for correct operation.Please wait for the
receiver to respond to the transmitter
0DQXDO2SHUDWLRQ
67(3: Plug in and turn the mains power supply on.
67(3 Turn the switch on the right hand side of the heater outlet to ³I´position.
67(3 Press the button to turn on the appliance.
67(3Press the button once to activate the low heat setting , press it again to activate the high heat setting,
press it a third time to switch the heat setting off.
67(3 To change the flame brightness , press the button to cycle through the brightness options.Turn
off the LED flame effect by pressing the button repeatedly until the flame effect cycles off.
127( press button 3 seconds to turn on the downlights function.
67(3 Activate the standby mode by pressling the button again.
67(3Switch the fire off by turning the switch on the right hand side of the heater to the ³0´position.
5HPRWH&RQWURO2SHUDWLRQ
67(3: Switch on the appliance using the switch.
67(3 Press the power button on the remote control; the LCD display will illuminate.
67(3 Press³)/$0(´button on the remote control to select the desired flame brightness; there are 3 different
brightness levels available.
67(3Select the desired heat output by pressing the relevant heat setting button:
To activate the low heat setting, press³+($7O´press it again to turn it off.
To activate the high heat setting, press³+($7OO´press it again to turn it off.
STEP 5: Press the "+" button on the remote control to increase the set temperature.
Press the "-" button to decrease the set temperature. The temperature can be set beweet 15-30℃.
If the room temperature is higher than the set temperature on the appliance, the heat will turn off.
If there is no operation for a few seconds, the remote control will show room temperature.
6HWWLQJWKH&XUUHQW'D\DQG7LPH
The day and time can only be set using the remote control.
67(3:Press the ³'$7(7,0(´button on the remote control , the day of the week will flash, Use the up and down
buttons to set the day of the week.Once the current day is set , press the “'$7(7,0(” button to confirm the current day.
67(3 The hour setting will then flash once the day has been selected .Use“”or “” to adjust the time until the current hour is
selected.Press the “'$7(7,0(” button to confirm the current hour.
67(3Then the minute setting will flash once the hour has been set.Use“”or “” to adjust the time until the current minute is
set correctly.Press the “'$7(7,0(” button to confirm the current minute.
8

When the window function is turned on, the temperature setting function will be disabled.
When the timer is set on, the window function will be disabled.
Safety Cut-out System
The fire suite is fitted with a thermal safety cut-out device, built in to prevent it from overheating.
Should the fire suite start to overheat, due to blocked air vents, the thermal safety cut-out system with automatically
operate and the heat settings will switch off. If this happens:
STEP 1: Switch off the fire suite using the ON/OFF switch, ensuring it is in the "O" position.
STEP 2: Check that the fire suite is unplugged from the mains power supply and allow it to cool for approximately
15 minutes.
STEP 3: Clear any blockages present on the vent,taking care not to damage the fire suite.
STEP 4: Plug in and switch on the fire suite at the mains power supply.
Caution: In order to avoid a hazard, due to inadvertent resetting of the thermal cut-out,the fire suite must not be
supplied through an external switching device such as a timer, or connected to a circuit that is regularly switched
on and off by the product.
NOTE: TIMER ON logo showed on the handset screen indicates that the weekly timer is enabled, the fire will operate
according to the set time. If you want to operate the fire manually press the TIMER ON/OFF button to turn off the weekly
timer.
The fire heater will operate to the set temperature when the weekly time is turned on, if you press any of the following
buttons “DOWN LIGHT”, “WINDOW”, ”+”, ”-“, “FLAME”, “HEAT I” and “HEAT II”.

13
13
NOTE: If the sensor fault of shortcut and open circuit, the indicator light on and button on the appliance will
blink in the same time. If the fault is removed, the indicator light on and button on the appliance stop blink.
‘

1000
1000
600
230
265
165
155
280
500
800
600
280

Making a claim:
      
    
 
   

 
Details required:
  
    
 
  
  
C
UK
CA

 




 
  
     