Firegear Kalea Bay OFP-36LECO-NLED User manual

16
KALEA BAY: ECOFLOW + LED
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS
DO NOT ATTEMPT TO INSTALL OR OPERATE THIS APPLIANCE
Warning: For Outdoor Use Only
INSTALLATION PRECAUTION:
This replace requires a minimum 18-square inches (per side) of cross ventilation.
Failure to provide proper ventilation can void the warranty.
MODELS
MH# 60069
Natural Gas Description
OFP-36LECO-NLED 36” Open Front Fireplace
OFP-48LECO-NLED 48” Open Front Fireplace
OFP-60LECO-NLED 60” Open Front Fireplace
OFP-72LECO-NLED 72” Open Front Fireplace
Kalea Bay Outdoor
Gas Fireplace with LED Lighting
Installation and Operating Instructions
LED MODEL
DO NOT DISCARD. THIS MANUAL
HAS IMPORTANT OPERATING AND
MANTENANCE INSTRUCTIONS.
LEAVE WITH THE HOMEOWNER.
MODEL:
SERIAL #:

17
KALEA BAY: ECOFLOW + LED
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 8
FRAMING FIREPLACE
NG Models:
NG
Factory
Orice
NG
Btu’s
High
NG
Btu’s
Low
NG Low
Rate
Screw
LP
Conversion Kit
LP Factory
Orice
LP Low Rate
Screw
OFP-36LECO-NLED #41 31,000 18,500 #44 OFP-36LECO-LPK OAS-LP52 ECO-LSS-52
OFP-48LECO-NLED #32 43,500 24,500 #34 OFP-48LECO-LPK OAS-LP48 ECO-LSS-46
OFP-60LECO-NLED #30 50,000 36,000 #27 OFP-60LECO-LPK OAS-LP44 ECO-LSS-42
OFP-72LECO-NLED #25 65,000 42,000 #18 OFP-72LECO-LPK OAS-LP42 ECO-LSS-35
Disclaimer: Btu listings are based on 7.0”WC for Natural Gas at inlet side
of gas regulator. Flex line sizing and proper gas pipe sizing can affect Btu’s.
As a result, your Btu’s may vary slightly from Table 1 specications.
NOTE: These replaces come shipped as Natural Gas models only. There is an LP conversion kit available as an
accessory. Ensure you order the specic conversion kit for your model replace. Table 1 shows the applicable information
if converting to Liquid Propane (LP) gas. See page 32.
IMPORTANT: It is permissible to reverse the burner pan in the eld to enable a closer gas line connection if necessary.
SPECIFICATIONS
Table 2 Gas Pressures
Pressure NG LP
Min. Inlet 5.0” WC 10.5” WC
Max. Inlet 10.5” WC 13.0” WC
Normal Inlet 7.0” WC 11.0” WC
Manifold 4.0”WC 10.0”WC
Fig. 4 The replace ships on a wooden skid. Remove the
screws as shown and lift replace off of skid.
Note: Number of screws vary with model size.
Table 1. Fireplace specications and conversion kits.

18
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 11
SINGLE-SIDED FIREPLACE DIMENSIONS & CLEARANCES
Table 4 Fireplace dimensions and clearances. Ensure you follow the proper clearances during installation.
Fig. 5 Fireplace dimensions; refer to Table 3.
Model:
Natural Gas (NG) A
Overall
Length
B
Inside
Opening
C
Overall
Height
D
Opening
Height
E
Overall
Depth
F
Leg
Height
G
Valve
Box
Depth
H
Clearance
To
Combustible
Side Wall
I
Clearance
To
Combustible
Ceiling
OFP-36LECO-NLED 40” 36” 37½” 16” 16¼” 11½” 10¼” 6” 42 ½”
OFP-48LECO-NLED 52” 48” 37½” 16” 16¼” 11½” 10¼” 6” 42 ½”
OFP-60LECO-NLED 64” 60” 37½” 16” 16¼” 11½” 10¼” 6” 42 ½”
OFP-72LECO-NLED 76” 72” 37½” 16” 16¼” 11½” 10¼” 6” 42 ½”
Fig. 6 Single-sided replace clearance to
combustibles (See Table 3) Fig. 7 Open front replace mantel clearances
FRONT VIEW
TOP VIEW
END VIEW
E
E
C
6”
20”
F
D
A
B
GBottom Finish Fin
Hood
½”
½”
(Typ. Each Side)
(Typ. Each Side)
I
H
END VIEW
SIDEWALL
CEILING
FLOOR
11½”
Back Front
END VIEW
12”
18”
TOP OF
FIREPLACE
6”
12”
Non-Combustible
Facing Material
Combustible
Material Permitted
Combustible
Shelf
Metal Studs
KALEA BAY: ECOFLOW + LED

19
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 12
Model:
Natural Gas (NG) A
Width
B
Height
C
Depth
OFP-36LECO-NLED 40 ½” 37 ¾” 15¾”
OFP-48LECO-NLED 52 ½” 37¾” 15¾”
OFP-60LECO-NLED 64 ½” 37 ¾” 15¾”
OFP-72LECO-NLED 76 ½” 37 ¾” 15¾”
Fig. 8 Framing dimensions using all non-combustible materials for single-sided replace; refer to Table 4.
SINGLE-SIDED FRAMING DIMENSIONS WITH METAL STUDS
Table 5 Fireplace framing dimensions.
NOTE: This replace requires metal studs for framing. WOOD STUDS ARE NOT PERMITTED.
A
B
Metal Studs Metal Studs
*Metal studs shown in gray.
Bottom Support Fin
Hood
C
Metal Studs
Metal Studs
(Front)
NOTE: This outdoor replace is not a “load bearing”
replace. All nishing materials must be supported
by the surrounding structure and not rely on the
replace itself.
KALEA BAY: ECOFLOW + LED

20
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 14
END VIEW
12”
18”TYP.
TOP OF
FIREPLACE
6”
12”
Non-combustible
facing material
Combustible
Material Permit-
Metal
Studs
6”
12”
Combustible Shelf
Combustible Shelf
Fig. 11 See-through replace mantel clearances
SEE-THROUGH FIREPLACE DIMENSIONS & CLEARANCES ONLY
Table 6 Fireplace dimensions and clearances.
Fig. 9 Fireplace dimensions; refer to Table 6
Model:
Natural Gas
(NG)
A
Overall
Length
B
Inside
Opening
C
Overall
Height
D
Opening
Height
E
Overall
Depth
F
Leg
Height
G
Valve
Box
Depth
H
Clearance
To
Combustible
Side Wall
I
Clearance
To
Combustible
Ceiling
OFP-36LECO-NLED 40” 36” 37½” 16” 16” 11½” 10¼” 36” 42 ½”
OFP-48LECO-NLED 52” 48” 37½” 16” 16” 11½” 10¼” 36” 42 ½”
OFP-60LECO-NLED 64” 60” 37½” 16” 16” 11½” 10¼” 36” 42 ½”
OFP-72LECO-NLED 76” 72” 37½” 16” 16” 11½” 10¼” 36” 42 ½”
Fig. 10 See-through replace clearance to
combustibles (See Table 6)
I
H
END VIEW
SIDEWALL
CEILING
FLOOR
11½”
Front
Front
This replace ships from the factory as a single sided replace, but by removing the back panels you can convert it
into a see-through replace. Your specic application, single sided verses see-through, will determine your installation.
Ensure you follow the proper clearances during installation.
FRONT VIEW
TOP VIEW
END VIEW
E
E
C
6”
20”
F
D
A
B
G
Bottom Finish Fin
Hood
½”
½”
(Typ. Each Side)
(Typ. Each Side)
KALEA BAY: ECOFLOW + LED

21
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 15
Model:
Natural Gas (NG) A
Width
B
Height
C
Depth
OFP-36LECO-NLED 40 ½” 37 ¾” 15”
OFP-48LECO-NLED 52 ½” 37¾” 15”
OFP-60LECO-NLED 64 ½” 37 ¾” 15”
OFP-72LECO-NLED 76 ½” 37 ¾” 15”
Fig. 12 Framing dimensions using all non-combustible materials for see-through replace; refer to Table 7.
SEE-THROUGH FRAMING DIMENSIONS WITH METAL STUDS
Table 7 Fireplace framing dimensions.
NOTE: This outdoor replace is not a “load bearing”
replace. All nishing materials must be supported
by the surrounding structure and not rely on the
replace itself.
A
B
Metal Studs Metal Studs
* Metal studs shown in gray.
Bottom Support Fin
Hood
C
Metal Studs
Metal Studs
Top view showing ½”lip using
non-combustible facing material at front face
NOTE: This replace requires metal studs for framing. WOOD STUDS ARE NOT PERMITTED.
KALEA BAY: ECOFLOW + LED

22
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 16
This replace is equipped with LED lighting. Preparation for the LED lighting a must be planned before the replace
nish materials are installed. After the replace is set in its nal location the LED lighting will need to be installed and
tested before nishing materials are applied. You will need to provide the following:
(1) 120VAC GFCI outlet double gang junction box with a weatherproof cover. Provides power to LED lights and gas valve
system. Follow local electrical codes for installation.
A RGB control box with switches is provided with the replace. It must be installed within the framing parameters of the
replace.
Step 1: Install the GFCI outlet
double gang junction box with a
weatherproof cover on the opposite
side of the inlet gas supply.
Note: This is not a requirement;
however, with the gang box on the
opposite side of inlet will create
more room for LED installation.
Fig. 15 shows GFCI gang box
installed.
Step 2: Find mounting location for the GFCI gang box. Fig. 14 shows at area underneath burner pan. Mount box
underneath the burner pan, below the square (cutout) hole area. Fig. 15 shows the GFCI outlet double gang junction box
with a weatherproof cover mounted underneath the replace.
Burner Pan
Support leg under replace
B
ot
t
o
m
s
u
p
p
o
r
t
n
GFCI Outlet installed in a double
outlet NEMA 3R enclosure
(Bring electrical up
from underneath
the replace)
Fig. 14 GFCI box location under replace
GFCI Outlet installed in a double
outlet NEMA 3R enclosure
Fig. 15 Show GFCI box mounted in replace
LED LIGHTING INSTALLATION
36”Model = 13”
48“ Model = 18”
60“ Model = 24”
72”Model = 30”
5”
11½”
TYP
Electrical Area (GFCI)
The electric junction box (GFCI) with a weatherproof cover must be installed in
the shaded area shown below. Ensure the j-box is close to the oor area where
the replace is sitting and not touching the burnerpan.
Fig. 13 Electrical placement.
KALEA BAY: ECOFLOW + LED

23
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 17
Step 3: Locate the wire grommets inside the rebox. See Fig. 16. Directly above them will be a series of mounting holes
for the windshield and LED retainer clips. Prepare the replace by installing the LED retainer clips. The retainer clips have
two holes in them. Install one (1) clip on the left and one (1) clip on the right side of the inner replace side wall. Install as
shown in Fig. 17. Note: if you are preparing a see-through replace you will install a total of (4) retainer clips two on open
side.
LED Retainer Clip
Fig. 17 Shows clip installed on right side of replace
Wire Grommets
Fig. 16 Locating wire grommets
Step 4: Install the four (4) windshield clips, two on each side, one at the top and one with the LED retainer clip as shown
in Fig. 18. Note: if you are preparing a see-through replace you will install a total of (8) windshield clips, four on each
open side.
Fig. 18 Installing windshield clips
Precaution: When installing windshield clips do
not secure the screws tight. They need to be loose
enough to allow the clip to move slightly and spin
around. Loose clips provide windshield to be easily
installed.
LED LIGHTING INSTALLATION
KALEA BAY: ECOFLOW + LED

24
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 18
Step 6: Carefully push the LED channel assembly connector through the wire grommet. As you push it through the
grommet sit the channel into the retainer clip. Ensure the other end of the channel is also sitting inside the other retainer
clip. See Figs. 20 & 21 as a reference. Note: If you are installing into a see-through replace install the other LED light
strip and channel the same direction.
Wi
reGrom
m
et
B
o
t
t
o
m
E
nd
LED Channel
Assembly
Fig. 20 Installing LED lights and channel Fig. 21 LED installed in retainer clip inside replace
LED LIGHTING INSTALLATION
Step 5: Remove the LED right channel assembly from the carton (The front of the channel has a shield facing the front
with the LED wire hanging on the right side). See Figs. 19-21 for details. Note: If you are installing into a see-through
replace you will install both right and left channels assemblies.
Fig. 19 Shows LED right channel
B
o
t
t
o
m
E
nd
LED Channel Assembly
Installed in retainer clip
KALEA BAY: ECOFLOW + LED

25
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 19
Step 7: Remove the screws from the “bottom end” of
the burner pan area. The bottom end part lls the space
between the burner pan and the replace side panel. It
is held into place with three (3) screws. See Fig. 22. First
remove the two inside screws, then the screw securing the
side wall. Lift up the area where the two screws were and
push down where the single screw was, then lift the
bottom end out of the replace.
Step 8: With bottom end removed, insert the LED channel
assembly female connector (protruding through the wire
grommets) to the LED male connector 77110. Note: The
male end of the LED connector will only insert into the
female connector in one direction. Once locked in
position, screw the threaded cap of the female connector
securely over the male connector. See Fig. 23.
Step 9: Attach 77110 to 77111 using the molex
connectors. After connecting the LED lights into the 77111
wire harness insert the 12-volt adapter 77102 with ¼”
terminals) into the (red & black wires) of LED wire
harness. Plug the 12-volt adapter into the 120VAC GFCI
box with weather proof cover. See Fig. 26, page 21.
LED LIGHTING INSTALLATION
Bottom End
1. Remove Screws
2. Lift up
3. Push down
V+
LED Lights
Male
Female
Female
Male
LED Lights
From
Fireplace
Inside Fireplace
LED Light Connection
12-volt adapter;
6-foot long
#77102
24-inch LED Wire Harness
# 77110
10-foot LED Controller Wire
Harness #77111
Connects to RGB Control Box
(dimmer and switches)
Female Male
Female
Male
Male
Female
(Molex Connectors)
Fig. 22 Removing bottom end
Fig. 23 LED wire connection
KALEA BAY: ECOFLOW + LED

26
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 20
LED LIGHTING INSTALLATION
Step 10: Remove the RGB control box from the components parts carton. Find a suitable location within a close
proximity of the replace for convenience of operation and mount the control box upright and level as shown in Fig. 26,
page 21. Use Figs 24 & 25 for dimensional reference. The replace is supplied with 10-feet of wiring for the RGB control
box (switches and dimmer) installation. Note: If desired, you can purchase 10-feet wire extensions in the accessories
section that will enable you to move the RGB control box up to 50-feet away from the replace. CAUTION: Ensure all
switches are in the OFF position. “I” indicates ignite/ON and “O” indicates OFF. Learn button does not apply.
Step 11: Remove the four (4) outer screws from each corner inside the cover plate and lift off. See Fig. 24. This will
expose the mounting plate. See Fig. 25. CAUTION: Do not remove the two center screws from the cover plate. This will
release the entire switch box wiring from inside the junction box and make it difcult to reinstall.
Take note of the 8-PIN (77115) and 6-PIN (77111) wire connectors. These are labeled LED lights (6-PIN) and Control
Module (8-PIN) connections. These will be the nal connection to the replace and crucial to the operation.
Step 12: Find a desired location to mount the RGB control box. Cut a 6” wide x 5 ½” tall hole into the cement board. See
dotted line in Fig. 25. Mount the RGB control box. Note: The wires from the switches can be removed for eaiser
installation, if needed. Ensure to match the wires with the labels for each switch when reattaching.
Step 13: Remove the 8-PIN module wire harness (77116) from the components part box. Locate the 8-PIN male
connector from the valve box (under the replace) and connect it to the 8-PIN female end of the wire harness.
Connectors only attach one way; press together until it snap locks into place. See Fig. 26, page 21 for details.
Step 14: Feed the other end of the wire harness through the square access hole underneath the fireplace and pass the
GFCI box, outside the fireplace to the RGB control box and connect. Connectors only attach one way; press together
until it snap locks into place.
Step 15: Locate the two ¼” male terminals from the valve box and connect the AF-4000ADP24 adapter. Plug the 7.5VDC
adapter into the 120VAC GFCI box.
Step 16: Locate the 6-PIN wire harness (77111) for the LED lights and feed the wire harness up to the RGB
control box and attach. Connectors only attach one way; press together until it snap locks into place. See Fig. 26, pg 21.
Step 17: Plug 12-volt adapter (77120) into the 120VAC GFCI outlet double gang junction box described on page 16.
Step 18: Plug 77115 into 77116 to connect the control module to RGB control box then connect the AF-4000ADP48EXT
to the AF-4000ADP24 and plug it into the 120VAC GFCI outlet double gang junction box. See Fig. 26, pg 21 for reference.
Fig. 24 RGB control box with 8 ¾” x 8 ¾” cover plate.
LED ON/OFF ON/OFF HI/LOW LEARNIPI/CONT PILOT
RGB DIMMER
LED ON/OFF ON/OFF HI/LOW LEARNIPI/CONT PILOT
RGB DIMMER
5 /”
6 /”
Fig. 25 RGB control box mounting plate
KALEA BAY: ECOFLOW + LED

27
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 21
Switch Cover
LEDON/OFF ON/OFF HI/LOW LEARNIPI/CONTPILOT
RGBDIMMER
#77116
#77115 #AF-4000ADP24
#AF4000ADP48EX #77102
#77114
#77113
#77111
LED Tray Assy
#77110
#77102
D
e
t
a
i
l
o
f
H
i
d
d
e
n
w
i
r
e
s
Fig. 26
Overview of replace wiring to control box. Note: The replace is provided with 10-feet of wire. If you require a longer length, an
optional 10-foot wire harness 77116 & 77111 are available in replaemet parts section.
LED LIGHTING INSTALLATION
KALEA BAY: ECOFLOW + LED

28
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 22
77111
77110
77114
77113
77112
77116 77115
INPUT OUTPUT
RGB DIMMER
LEARN
ON/OFF
HI/LOW
IPI/ CONT PILOT
RED TERMINAL
BLUE TERMINAL
LED ON/OFF
LED LIGHT STRIPS
77102
VCS-ECOMOD
(Under glass panels)
(Inside valve box)
REPRESENTS COMPONENTS INSIDE
LED CONTROLLER BOX
(12VDC adapter inside a
weatherproof box)
REPRESENTS COMPONENTS
INSIDE FIREPLACE
AF-4000ADP24
(7.5VCD adapter powers
gas valve system)
Brown
Blue
Yellow
Black
Red
Note: If using single-sided fireplace only one LED connection will be used.
AF-4000ADP48EXT
Fig. 27 This wiring diagram shows the LED circuit in relationship to the IPI gas valve control system. Each is independent of the other.
LED WIRING DIAGRAM
KALEA BAY: ECOFLOW + LED

29
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 23
VALVE SAFETY WIRE
(V-Wire)
AF-4000ADP48EXT
CONNECTS TO
AF-4000ADP24 ADAPTER
VCS-ECOMOD
(Control Module)
1/2 PSI SPAIN
INLET
OUTLET
PILOT TUBE
S
I
SWITCHES
POWER
MOTOR COMM.
BATT
V
BRONZE INSULATED WIRE
BLACK WIRE
BRASS WIRE
(GROUND)
MOTOR DRIVE WIRES
TO
120VAC
POWER
SWITCHES MOUNTED
IN RGB CONTROL
ASSEMBLEY
LOW RATE SET SCREW
Fig. 28 This wiring diagram shows the components inside the valve box.. The dotted line box shows the components external of the valve box.
GAS VALVE WIRING DIAGRAM
KALEA BAY: ECOFLOW + LED

30
KALEA BAY: ECOFLOW + LED
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 25
FINAL PREPARATION
Fig. 32 Installing media into the replace.
Table 8 Media specications. Requires ½” - ¾”
reglass (Burner pan media amount does not include
the trough)
Burner
Trough
½” - ¾”
Crushed Glass
FINAL PREPARATION
BURNER PAN ASSEMBLY
Pilot
(Hidden Underneath)
Burner
Tube
Ignition
Hole
PILOT OPERATION & TEST FIRE
The pilot assembly is located at the end of the burner,
hidden underneath the mesh screen cover location.
Ensure the pilot ame is passing through the ignition hole,
in the burner pan, for proper ignition. Use the Fig. 31 as a
guide.
Test re the replace before installing media to ensure
ame is passing through igniton hole as shown in Fig. 31.
This is a good time to double check for any gas leaks or
electrical connections before nalizing the installation by
installing the glass media.
Fig. 31 Proper pilot ame through ignition hole.
INSTALLING MEDIA
Use Firegear Outdoors large broken glass media (not
supplied). Table 8 will specify the proper amount needed.
Place reglass media into the trough area rst as shown
in Fig. 32. Use the remaining media to ll the burner pan
equally on both sides. After lling the trough install the
mesh screen hood overtop of the pilot area.
Keep media in burner pan the same level as the trough to
allow the burner area to appear as one complete
burner pan.
IMPORTANT: Media can only be placed in the trough and
burner pan area. No media is to be place into the shaded
area shown in Figs. 34, page 26.
CAUTION: Ensure there is no media in the ignition hole
area. The burner tube gas ignites in this area to light the
replace. Media in this area could cause delayed ignition.
The replace requires ½”-¾” large broken reglass to be
installed into the burner trough and burner pan. Use the
table below to assist in determining the amount of media
needed for your specic model.
Large Broken Glass
Model # Burner pan & Trough
36” 15lbs.
48” 20lbs.
60” 25lbs.
72” 25lbs.
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 25
FINAL PREPARATION
Fig. 32 Installing media into the replace.
Table 8 Media specications. Requires ½” - ¾”
reglass (Burner pan media amount does not include
the trough)
Burner
Trough
½” - ¾”
Crushed Glass
FINAL PREPARATION
BURNER PAN ASSEMBLY
Pilot
(Hidden Underneath)
Burner
Tube
Ignition
Hole
PILOT OPERATION & TEST FIRE
The pilot assembly is located at the end of the burner,
hidden underneath the mesh screen cover location.
Ensure the pilot ame is passing through the ignition hole,
in the burner pan, for proper ignition. Use the Fig. 31 as a
guide.
Test re the replace before installing media to ensure
ame is passing through igniton hole as shown in Fig. 31.
This is a good time to double check for any gas leaks or
electrical connections before nalizing the installation by
installing the glass media.
Fig. 31 Proper pilot ame through ignition hole.
INSTALLING MEDIA
Use Firegear Outdoors large broken glass media (not
supplied). Table 8 will specify the proper amount needed.
Place reglass media into the trough area rst as shown
in Fig. 32. Use the remaining media to ll the burner pan
equally on both sides. After lling the trough install the
mesh screen hood overtop of the pilot area.
Keep media in burner pan the same level as the trough to
allow the burner area to appear as one complete
burner pan.
IMPORTANT: Media can only be placed in the trough and
burner pan area. No media is to be place into the shaded
area shown in Figs. 34, page 26.
CAUTION: Ensure there is no media in the ignition hole
area. The burner tube gas ignites in this area to light the
replace. Media in this area could cause delayed ignition.
The replace requires ½”-¾” large broken reglass to be
installed into the burner trough and burner pan. Use the
table below to assist in determining the amount of media
needed for your specic model.
Large Broken Glass
Model # Burner pan & Trough
36” 15lbs.
48” 20lbs.
60” 25lbs.
72” 25lbs.
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 26
FINAL PREPARATION
Fig. 34 Covering the entire replace oor is NOT permitted
in the shaded area.
Note: Media amounts listed in Table 8 are guides and can
vary depending on media used. Ensure not to cover more
than ½ -inch above the actual burner tube and keep all
media within the burner pan area (See Fig.34).
Fig. 33 End view of burner with media.
Burner Pan End View Showing Media Placement
Proper Media Height
Burner Tube
Large Broken Glass in
Burner Trough and
Burnerpan
No Media on
Mesh Screen Cover
No Media in
Shaded Areas
INSTALLING HOOD(S)
The replace requires a hood to be installed into the upper opening of the rebox. All models require ve (5) screws to
secure the hood to the replace except the 72-inch model, which uses seven (7) screws to secure the hood. The hood
protrudes 1-inch from replace opening. Fig. 35 shows hole location and installation process for hood installation. The
protruding area of the hood is to be angled downward for proper installation, see Hood Detail below.
Fig. 35 Installing hood(s) on the replace.
Hood Screw Locations
FRONT VIEW SIDE VIEW
Hood
(Deector Facing Downward)
Hood Detail
End View

31
KALEA BAY: ECOFLOW + LED
Kalea Bay LED Outdoor Fireplace REV. 4-17-19 Page 38
OPTIONAL ACCESSORIES
The following accessories are available from your local Firegear dealer/distributor.
Each accessory comes with a separate installation manual. Read each instruction thoroughly before installing.
Firegear Outdoors Media
GRL-Series (Reective Glass in sev-
eral colors)
LED See-Thru Conversion Kit
73231 (36-inch model)
74231 (48-inch model)
75231 (60-inch model)
76231 (72-inch model)
Kit includes: hood, right/left glass
holders & screws
LP Conversion Kit
Model:
OFP-36LECO-LPK (36-inch model)
OFP-48LECO-LPK (48-inch model)
OFP-60LECO-LPK (60-inch model)
OFP-72LECO-LPK (72-inch model)
Converts replace from Natural gas
to LP gas. See page 29 in manual.
Wireless Wall Switch
Wireless wall switch (ON/OFF/HI/LO)
Model: 1322-WT
Wireless Wall Switch
Wireless wall switch (ON/OFF) ONLY
Model: 1001D-ATX
Wireless Wall Switch Timer
4-Button Wall Timer (30/60/120/OFF)
Model: TM-R-AF1TX
Home Automation System
Model: AF-4000HAT
Enables the replace to operate with a
home automation device.
Additional Remotes
Model: RCAF-3TX (hand held remote)
Twig Set
Model: 926-930
6 piece Beach Driftwood twisted twig
set.
NOTE: Logs cannot be placed
directly on the burner. They must be
placed around the burner.
Weatherproof Covers
Models: OFP-36COV
OFP-48COV
OFP-60COV
OFP-72COV
Stainless steel cover to protect
replace during none use times.
ON
OFF
HI
LO
30 MIN
60 MIN
120 MIN
OFF
FOR TECHNICAL SERVICE, CALL:
Firegear Outdoors
9230 Conservation Way
Fort Wayne, IN 46809
[phone]
Sales Support: [phone]
WEB SITE: www.regearoutdoors.com
[phone]
Note: Remote controls and wall mount switches listed above are not waterproof product therefore it is strongly suggested
to install them into a waterproof enclosure or keep protected from the outside elements.