Foldcraft Plymold Z000000127 User manual

FlatBenches

Revised03/0317
Z000000127
IslandStyle

FlatBenchIslandFramePage2of5
UnpackingYourShipment
Unpackandidenfyeachcomponentineachboxthatyoureceived.Ifyourshipmentismissingparts,ortoomany
partswereshipped,pleasecontactPlymold.
Components
ISLANDSTYLEFRAME
ADJUSTABLEPLASTIC
GLIDE(A)
ToolsRequired





SCREWGUNW/#2PHILLIPSBITPENCILORMARKER  




SOCKET,RATCHET,ANDWRENCHSET LEVEL  TAPEMEASURE SCREWDRIVER

EXPANSIONSPACER
NUT1/4‐20
1/4‐20x3/4”BOLT
P85888JUPITER
FRAMEHARDWAREKIT
PLASTECFLOOR
ANCHOR
SCREW#10X1”
P85889JUPITER
TABLE&FLOORHARDWAREKIT
REARSEATHOOK
P85794HARDWAREKITFLATBENCH
TEKSCREW#10x1”
TABLETOP
FLATBENCH

FlatBenchIslandFramePage3of5
Assembly
Step2:AssembleSeattoFrame
a.Note:Anexpansionspaceris
requiredfortabletopswider
than24”.






b.Alignthetableangleholes.





c.LocatetheJupiterFrameHardwareKitandfastenthetwoframehalvesto‐
getherusing1/4‐20x3/4”boltsandnuts.
Note:Handghtennutsandbolts.

d.Leveltableangles.

e.Tightennutsandboltsusingawrench.



Step1:GlideAssembly‐IslandStyleFrame
a.Assembleathread‐inglideintothein‐
sertineachofthefour(4)legs.




FlatBenchIslandFrame
Step3:AssembleSeattoFrame
a.LocateFlatBenchhardwarekit.
b.Posionseatcenteredonislandframe.
c.Insertshorttongueofrearseathookintotheseatplate.Usingaflatheadscrewdriverpryrearseathook
unlitpopsintoplace.(4xperBench)Note:BoothHooksshouldbeinsidetheframe.

Assembly
Page4of5
d.Nowthattheseatisinstalled,insertaself‐drilling
screwintotheholeintherearseathook.Onescrew
foreachrearseathook.Donotoverghten.
Screwdriveshownprying
rearseathookoncontour
seat.Samemethodusedfor
flatbench.
Step4:InstallingTableTop

a.LocatetheJupiterTable&FloorHardwareKit.
b.Placethetabletopontheframe.
c.Posiontableperdrawingsbelow.
d.Securethetabletopfrommovingwhilefastening,using(16)#10x1.0”screws.
CENTER
CENTER

FlatBenchIslandFrame
Step6:FastenGlidestoFloor

a.Rotateglidestopointthemounngholetowardsthecenterofthebooth.
b.Withapencil,marktheholelocaononthefloorusingtheholesintheglide.
c.Turntheglideaway90degreesfromitscurrentposiontoexposethemarkon
thefloor.
d.Usingahammerdrillanda1/4”masonrybit,drilla11/4”deepholeonthe
pencilmark.
e.Placeaplascanchorintheholeandthenrotateglidebacksotheholelinesupwiththeplascanchorin
thefloor.
f.Inserta#10x1.0”screwthroughtheholeintheglideandsecureintotheplasc
anchor.

Note:Framesmustbeanchoredtothefloortomaintainstabilityandprevent
personalinjury.

Assembly
Page5of5
Step7:Care.
a.Cleanfurnitureandprotectunitunlreadyforuse.
Step5:PosionandLevelBooth

a.Confirmlocaonofbooth/frameswiththefloorplan.
b.Levelboothbyadjusngglides.