Foldcraft Plymold Z000000055 User manual

Bolt Down Seat
and Table Posts
Released 02/14/22
Z000000055
Address 615 CENTENIAL DRIVE
KENYON, MN 55946
Web Plymold.com
Phone 800.PLYMOLD
A Division of Foldcra

Page 2 of 5
Unpacking Your Shipment
Unpack and idenfy each component in each box that you received. If your shipment is missing parts, please contact
Plymold.
Components
HARDWARE
SETTING
TOOL
‘T’ WRENCH
Dining Counter (Bolt Down)
Address 615 CENTENIAL DRIVE
KENYON, MN 55946
Web Plymold.com
Phone 800.PLYMOLD
A Division of Foldcra
BOLT DOWN TABLE POST
(CAN GET AN OPTIONAL
FOOT REST)
BOLT DOWN SEAT POST
(SHOWN WITH OPTIONAL
FOOT REST)
1/4” X 1-3/4”
LAG BOLT 5/16” WASHER
P87275 HARDWARE KIT—WOOD FLOOR
1/2” MULTI SET
ANCHOR
1/2”‐13 x 1‐1/4”
HEX HEAD BOLT
P87274 HARDWARE KIT—CEMENT FLOOR

Dining Counter (Bolt Down)
Assembly
Step 1: Mounng Posts to Concrete Floor
a. Mark the center locaon of each post onto the floor. (
b. Drill 5/8” diameter hole, a minimum of 2” deep into the cement at the marked locaons
c. Blow out the dust from the holes
d. Place an anchor into each of the 5/8” dia. Holes. (Note: The flange at the top of the an‐
chor should be resng on the cement surface.)
e. Insert the seng tool into the anchor and hit it with a hammer unl the shoulder of the
seng tool contacts the flange of the anchor.
f. Place the bolt down post over the anchors locaons.
g. Use a plasc bag or wrapper over the head of the 1/2”‐13 x 1‐1/4” hex head bolt. Insert it
into the socket of the ’T’ wrench provided. (The plasc bag helps keep hex head bolt from
falling out during installaon.)
h. Insert the ‘T’ wrench with bolt down the hole in the top of the column.
i. Insert the bolt into the anchor in the floor and turn the ‘T’ wrench to ghten. (do not fully
ghten at this me.)
j. Ensure that the pots are orientated square to the counter edge.
k. If needed shim posts to level by placing metal washers under the base plate.
l. Aer post is oriented and straight ghten bolt firmly.
NOTE: At the installers discreon, one can add addional holding power in cases where the
quality of the concrete is poor. You can do this by inserng masonry screws through the
outer 4 holes of the base plate under the bell cover.
SETTING
TOOL
5/8” HOLE
CEMENT
ANCHOR
T‐WRENCH
HEX HEAD
BOLT
BOLT DOWN
POST
Page 3 of 5
Address 615 CENTENIAL DRIVE
KENYON, MN 55946
Web Plymold.com
Phone 800.PLYMOLD
A Division of Foldcra
Step : Clean
a. Clean for use.
Step 1B: Mounng Posts to Wood Floor
a. Mark the center locaon of the 4 outer holes.
b. Drill 3/16” x 1 1/2” deep hole in the wood floor in the marked locaons.
c. Place the post back over the 4 pre‐drilled holes.
d. Using a 1//4” x 1‐3/4” Long Lag bolt and a 5/16” washer fasten the posts to the floor
BELL COVER RAISED UP TO
ACCESS HOLES FOR WOOD
FLOOR MOUNTING