Furniture of America CM3823PC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Page 1 of 5
DIFFICULT
ASSEMBLY RATING

Page 2 of 5

Parts List Hardware List
#1 x 1 pc x 2
Backrest w/ Legs
#2 x 1 pc x 2
Seat
#3 x 2 pcs x 2
Front Leg
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until each
step is completed or instructed.
MD
#A x 4 pcs x 2
Bolt 5/16”x3-1/4”
Page 3 of 5
#C x 4 pcs x 2
Bolt 5/16”x2-1/4”
#B x 2 pcs x 2
Bolt 5/16”x1-3/4”
#5 x 1 pc x 2
Front Leg Support
#G x 1 pc x 2
Wood Dowel
#D x 10 pcs x 2
Lock Washer
#F x 1 pc
Allen Wrench
#H x 6 pcs x 2
Screw
#4 x 2 pcs x 2
Side Leg Support
#E x 10 pcs x 2
Flat Washer
Note: The above parts and hardware are
shown for a complete assembly of ONE
chair. However, the actual parts and
hardware (with an exception of the wrench
andAllen wrench) in the box will be twice
the quantities listed to include the
assembly of the second chair.

Turn right (clockwise) to tighten
Page 4 of 5
#B x 2 pcs
#D x 2 pcs
#E x 2 pcs
#G x 1 pc
Turn right (clockwise) to tighten
I. Place the backrest with legs
(#1) on a protected surface.
Insert a wood dowel (#G) into
the center hole of the backrest
with legs (#1).
II. Align the seat (#2) with the
wood dowel (#G) and the pre-
drilled holes of the backrest
with legs (#1).
III. Prepare 2 bolt assemblies by
inserting FIRST the lock
washer (#D) onto the bolt (#B)
and then the flat washer (#E)
onto the SAME bolt (#B), in
that order.
IV. Insert the bolt assemblies
through the pre-drilled holes
on the seat (#2) and secure
those bolts using the Allen
wrench (#F) to lock them with
the backrest with legs (#1).
I. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#D) onto the bolt (#A) and then the flat washer (#E) onto the
SAME bolt (#A), in that order.
II. Insert the bolt assemblies through the pre-drilled holes on the
corners the seat (#2) and secure those bolts using the Allen
wrench (#F) to lock them with the backrest with legs (#1).
#A x 4 pcs
#D x 4 pcs
#E x 4 pcs

I. Insert the front leg support
(#5) between the 2 front
legs (#3). Then insert the 2
side leg supports (#4) into
the backrest with legs (#1)
and the 2 front legs (#3).
II. Align the 2 front legs (#3)
with the pre-drilled holes of
the seat (#2).
III. Prepare 4 bolt assemblies
by inserting FIRST the
lock washer (#D) onto the
bolt (#C) and then the flat
washer (#E) onto the
SAME bolt (#C), in that
order.
IV. Insert the bolt assemblies
through the pre-drilled
holes on the seat (#2) and
secure those bolts using
the Allen wrench (#F) to
lock them with the 2 front
legs (#3).
Page 5 of 5
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR.
Turn right (clockwise) to tighten
I. Secure the front leg support
(#5) and the 2 side leg
supports (#4) with 6 screws
(#H) using a Phillips
screwdriver to lock them with
the backrest with legs (#1)
and the 2 front legs (#3).
II. Carefully turn the completed
chair upright. Make sure the
chair is rested on a flat
surface and does not feel
loose or wobbly. If it does,
double check that the
bolts/screws are secured and
properly tightened.
#H x 6 pcs
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
Turn right (clockwise) to tighten
#4
#5
#3