Follett FZR Series Supplement

Installation, Operation and Service Manual
FZR Series
Undercounter Freezer
00156216R08
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
Fax [phone] • www.follettice.com
Following installation, please forward this manual
to the appropriate operations person.
Order parts online
www.follettice.com
Serial numbers before C45184

2
This page intentionally left blank.

3
Welcome to Follett
Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and
outstanding after-the-sale support. To ensure that this product delivers that same degree of service, we ask that
you take a moment to review this manual before beginning the installation. Should you have any questions or
require technical help at any point, please call our technical service group at [phone] or [phone].
Before you begin
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage.
If damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the
ling of a claim, if necessary.
Specications
Series specications
FZR5
34.00" height for freestanding use or installation below standard 36" (915mm) high counter
4.0 cu ft (usable cubic volume)
FZR4-ADA
31.25" height for freestanding use or installation below 34" (864mm) high ADA-compatible counter
3.3 cu ft (usable cubic volume)
Electrical specications
115V, 60Hz, 1 phase
Full load amps: 8.0
Minimum circuit ampacity: 15 amp
Maximum size of branch circuit overcurrent device: 15 amp
Refrigeration specications
Refrigerant – R404A
Charge size – 10 oz
Maximum design pressures:
High side – 383psi
Low side – 175psi
Installation specications
Ambient temperature must not exceed 100 F (38 C).
The front louvered panel must be kept free of any cabinet trim or obstructions to ensure proper ventilation of the
refrigeration system.
Important cautions
• Equipment must be wired according to local and NEC codes.
• Always disconnect power before servicing freezer.

4
Installation
Installing legs – required
1. Remove legs from plastic bag packed inside freezer.
2. Tip freezer back and screw legs in all the way to stop (they will extend
1/8" below base of freezer).
3. Adjust legs as needed to level freezer in both directions. To access
legs, remove the lower front panel. Turn legs clockwise to extend legs.
Installing shelves – required
1. Remove shelves and shelf brackets packed inside freezer.
2. Install shelf brackets in pilasters (insert top tab, squeeze and push in
lower tab).
Installing controller faceplate – required
The freezer is shipped from the factory congured to display in
degrees C. If degrees F display is desired, resetting of temperature
controller is required.
1. Remove degrees F and degrees C faceplates from plastic bag
packed inside refrigerator.
2. Snap appropriate faceplate in place over controller face.
Changing temperature controller settings – optional
Follett’s temperature controller is pre-programmed with a -25 C (-13 F)
set point and degrees C display. The -25 C (-13 F) set point delivers a
temperature range of -23 to -25 C (-9 to -13 F). Follett’s controller set point
can be changed to deliver up to a -15 C (+5 F) temperature for applications
where a lower temperature is not desired (i.e. ice cream). See page 6 to
change controller settings.
2
1
3
Fig. 1
Fig. 2
Fig. 3
Fig. 4

Reversing the door swing – optional
NOTICE
When reinstalling latch and hinge screws, 242 blue Loctite* MUST be
applied to screws. Torque screws to 25 in-lbs.
1. Remove screws and latch from refrigerator cabinet (Fig. 5.1).
2. Use at screwdriver to carefully remove (do not scratch) hinge
covers (Fig. 6.1).
3. Support door and remove screws attaching hinge to refrigerator
cabinet (Fig. 6.2).
4. Cover hinge screw holes with screw hole plugs removed from
opposite side.
5. Reverse door. Apply 242 blue Loctite to hinge screws and reinstall
torqued to 25 in-lbs.
6. Reinstall latch on opposite side.
7. Remove screws and handle from door (Fig. 7.1).
8. Rotate handle (Fig. 7.2).
9. Apply 242 blue Loctite to latch screws and reinstall torqued to 25 in-lbs.
5
1
2
1
1
2
1
2
Fig. 5
Fig. 6
Fig. 7
Loctite is a registered trademark of Henkel Corporation in the United States and other countries.