FOR-A FA-9520 User manual

1 POWER switch Pressing the "｜" side turns on the power.
2 FS1/LOCK
button
Used to select FS1. Press and hold down to lock the front panel operation.
Press and hold down again to unlock. In the FA-9520 mode, locks only the
operation for FS1.
3 FS2/LOCK
button
Used to select FS2. In the FA-9520 mode, locks the front panel operation for
FS2 when pressed and held down. Press and hold this button down again to
unlock.
4 EVENT button Used to save and load events.
5
Status indicator
VIDEO IN
green
Input signal
present in
FS1/FS2 REMOTE
green CONTROL SETTING
is set to REMOTE
Unlit No input signal
in FS1/FS2 Unlit CONTROL SETTING is set to LOCAL
AUDIO IN
green Assigned audio
signal present DC
POWER
Red Power failure
Unlit No assigned
audio signal Unlit Normal power supply
GENLOCK
green Genlock signal
present FAN
ALARM
Red Fan failure
Unlit No genlock
signal input Unlit All fans normal
6 Menu display Used to display menus and make operational settings
7 Controls
(F1-F4)
UNITY buttons
Used to change operational settings. Turn and select values.
The Unity buttons return the settings to the default values.
8 Arrow buttons Single-arrow Used to move between parameters. (lights if accessible)
Double-arrow Used to move between menus. (lights if accessible)
9 Menu buttons Used to select menus.
FA-9520
Quick Setu
p
Guide 3rd Edition
The F
A
-9520 has 2 operational modes; F
A
-9500 mode, in which
the unit operates/functions almost the same as the former
FA-9500, and FA-9520 mode with 2 independently operational
frame synchronizers. This quick setup guide mainly describes
operation in FA-9520 mode. To change the mode, see
Operation Manual section 7-2. “MU OPERATION”.
Packing list: FA-9520 (1), Quick Setup Guide (1) CD (including
Operation Manuals), AC cord (1), AC cord retaining clip (1 set),
Rack mount bracket set (1 set)
Option items: FA-95RU, FA-95PS (with AC cord, AC cord retaining
clip (1 set), FA-95DACBL (installed before shipment), FA-95D-D,
FA-95DE-E, FA-95AIO (with PC-3307-1 cable), FA-95ALA
Software option: FA-95CO
POWER
ON
OFF
PS1/LOCK
PS2/LOCK
EVENT
VIDEOIN
GEN LOCL
REMOTE
AUDIOIN
FANALARM
DCP OWER F 1
F 2
F 3
F 4
F A - 9 5 2 0HD / SD FRAME SYNCHRONIZER
DISPLAY F 1
UN ITY
F 2
UN ITY UNITY
F 3 F 4
UN ITY
PROCESS
SDIAUDIO
MA PP I N G
VI DEO OP
AU DIO OP
C C
A V O CLIP
DELAY
VID EO S YS
AUDI O S YS
AES AUDIO
CONV1
ANALOG
IN SEL
DOWNMIX
STATUS
OT HE R
CONV2
MA ST E R
OUT SE L
MODE
VIDEO
AUDIO
2. Installing the AC Cord Retaining Clip
After connecting the AC cord, secure the AC cord with the supplied ladder
strap/retaining clip assembly to prevent accidental removal from the FA-9520. Be sure
to install the AC cord retaining clip before mounting the unit into a rack.
1) Wrap the retaining clip around the AC cord. (with the anchor of the ladder strap
toward the unit.)
2) Insert the anchor into the hole next to the AC IN socket.
3) Lightly fasten the clip around the AC cord.
4) Plug in the power cord.
5) Slide the clip on the ladder strap toward the plug.
6) Fasten the clip tightly.
7) Gently pull on the AC cord to ensure it is secured.
Make sure that the FS1/LOCK and FS2/LOCK button LEDs are lit green or unlit
before starting an operation. If FS1/LOCK and/or FS2/LOCK button LED(s) are lit
orange, all operations on the front panel for FS1 and/or FS2 except the LOCK
button(s) are disabled. Press and hold the FS1/LOCK and/or FS2/LOCK button(s)
that are lit orange to unlock the operations.
5. Connecting via a WEB Browse
r
Open a web browser on your computer, and enter the address as
http://192.168.0.10/ (factory default setting) in the address bar.
Press the [Enter] key to connect to the FA-9520.
The login page is displayed.
Click Login.
The authentication dialog appears.
Enter your user name and password. (The default user name and
password are set at the factory.)
User name: fa9520
Password: foranetwork
See section 9. “Control via WEB Browser” for details on Web browser
control screens.
* Complete connections before turning the power of the unit on.
2)
4) 3)
5) 6)
1. Rear Connectors 4. Connecting a Compute
r
3. Front Operation Panel
ANALOG COMPONENT I/O
FA-95AIO option
A
nalog component input/output connecto
r
（use with the
supplied PC-3307-1 cable.)
Refer to sec. 16. FA-95AIO Option for details on connectors.
The F
A
-9520 network settings must be adjusted for your network after
purchase.
The FA-9520’s LAN1 IP address is set to 192.168.0.10 at the factory.
Set the IPaddress and subnet mask of the computer as follows:
IP address: 192.168.0.1 to 192.168.0.254 (except 192.168.0.10)
Subnet mask: 255.255.255.0
In Windows, open the Local Area Connection Properties dialog box,
and open the Internet Protocol (TCP/IP) Properties window. The
network settings must be made in the window. See the user’s manual of
your computer for details.
See section 9-8 “Network Settings” for details on changing the
FA-9520’s IP address.
The FA-9520’s IP address can be checked in the NETWORK INFO
menu (menu page 197). To go to the NETWORK INFO menu, press the
STATUS/OTHER button, then a single-arrow button.
*1 Refer to the Operation Manual section 12. “Analog Audio Connection” for details on the
Analog audio connector.
*2 Refer to the Operation Manual section 14. “REMOTE” for details on the Remote control
connector.
FA-95DACBL option
Digital audio output connectors
3/4 5/61/2 7/ 8
FAN2
3/4 7/8
FAN1
5/6
BA
COMPOSITE
1/2
LAN2
SDI
REMOTE
LAN1
COMPOSITE
OUT3OUT2IN1
SDI
ANALOG AUDIO
LAN2
DIGITAL AUDIO IN/OUT
OUT4OUT1 IN2 OUT1 OUT2IN
AC100-240V 50/60Hz IN 2
DIGITAL AUDIO OUT
SER.NO.
GENLOCKIN
AC100-240V50/60Hz IN 1
Digital audio input/output connectors
(Will be input connectors when the FA-95DACBL is installed.)
Direct connection using a crossover LAN cable is also possible.
Connection using a hub
AC100 -240V 50/60H z IN 1
FAN2
SER. NO.
LAN2LAN1
REMOTE
DIGITAL AUDIO IN / OUT
7 / 85 / 63 / 41 / 2
ANALOG AUDIO
GENLOCK IN
COMPO SITE
OUT2OUT1IN
B
OUT4OUT3IN2OUT2OUT1
SDI
IN1
A
FAN1
AC100 - 240V 50/60 Hz IN2
Straight-through
LAN cable
PC
LAN1
Reference signal input connector
FA-95D-D/DE-E option
OUTIN REF IN
Dolby E
Digital audio input connector Digital audio output connector
AC Power connector 1
AC100 - 240V 5 0/60 Hz I N 1
FAN2
SER. NO.
LAN2LAN1
REMOTE
DIGITAL AUDIO IN / OUT
7 / 85 / 63 / 41 / 2
ANALOG AUDIO
GENLOCK IN
COMPOSITE
OUT2OUT1IN
B
OUT4OUT3IN2OUT2OUT1
SDI
IN1
A
FAN1
AC100 - 240V 50/60 Hz IN2
HD/SD-SDI input connector 1
HD/SD-SDI output connector 1, 2
HD/SD-SDI input connector 2
HD/SD-SDI output connector 3, 4
A
nalog composite input connecto
r
A
nalog composite output connecto
r
Genlock input connector
Ground terminal
Ethernet port (for future use)
Ethernet port
Digital audio input/output connector
FAN1 SLOT A SLOT B
Analog audio Input/output connector *1
Remote control connector*2
FAN2
AC Power connector 2

10. Resetting to Default
The UNITY indicator light goes off when the setting value is changed
from the default value. Pressing the UNITY button while the light is off
returns the corresponding setting value to the default value. Then the
light goes off. Pressing the button again returns the value to the
previous value before resetting to the default value.
* The above procedure is in NORMAL mode. Normally the unit starts
up in NORMAL mode. There is another mode called LIVE SAFE
mode, in which some menus request a setting change confirmation to
protect important settings from accidental changes. If the unit is in
LIVE SAFE mode, see sec. 4-2-7. Resetting to Default.
Precautions
Operate the unit only at the specified supply
voltage.
Ensure the unit is properly grounded at all
times.
Ensure the power cord and connectors are
firmly connected.
Do not access circuitry with power applied to
the unit.
Unit should not be operated or stored with
the cover, panels, and/or casing removed.
Unit should not be operated or stored in a
humid, dusty, etc. environment. Doing so
could result in fire or electrical shock.
Do not allow fluids, metal fragments, or any
other foreign objects to enter the unit. If
foreign matter does enter the unit, turn the
power off and disconnect the power cord
immediately. Remove the material or contact
your authorized service representative
If you notice any strange smells or noises
coming from the unit, turn the power off
immediately, turn OFF the power switch,
disconnect the power cord, then contact your
authorized service representative.
8. Menu List (in F
A
-9520 mode)
Menu Button VIDEO menus (lit green) AUDIO menus (lit orange)
PROCESS
SDI AUDIO ◊⊚VIDEO PROC AMP
EMB1 IN GAIN
EMB1 OUT MONO
●EMB1 IN SET
●EMB1 OUT CLOCK
EMB2 IN GAIN
EMB2 OUT MONO
●EMB2 IN SET
●EMB2 OUT CLOCK
CC
AES AUDIO
⊚WHITE LEVEL
⊚BLACK LEVEL
⊚GAMMA LEVEL
COLOR CORRECT
AES IN GAIN
AES HYSTERESIS
AES OUT MONO
●AES I/O SETUP *3
CONV1
ANALOG
●CONV MODE
CONV SIZE/POS
CONV CROPPING
CONV IMPROVE
CONV SIDE RGB
ANALOG IN LEVEL
ANALOG IN GAIN
ANALOG OUT LEVEL
ANALOG OUT MONO
●ANALOG IN SYSTEM
CONV2
MASTER Not functioning
MASTER OUT GAIN
EMB1 OUT GAIN
EMB2 OUT GAIN
AES OUT GAIN
ANALOG OUT GAIN
AVO *1
MAPPING
●AVO SETTING
USER1-5 LEVEL SET
USER1-2 AREA SET
AVO SETUP *1
●EMB1 OUT REMAP
●EMB2 OUT REMAP
●AES OUT REMAP
●ANALOG OUT REMAP
CLIP
DELAY YPbPr/RGB CLIP COMPOSITE CLIP EMB1 OUT DELAY EMB2 OUT DELAY
AES OUT DELAY
ANALOG OUT DELAY
IN SEL
DOWN MIX
●FS INPUT SELECT
ANC DETECT LINE
ANC DETECT SEL
●AIO A IN MODE *1
●AIO B IN MODE *2
●DOWN MIX1 SET
●DOWN MIX1 ASSIGN
●DOWN MIX2 SET
●DOWN MIX2 ASSIGN
OUT SEL
MODE
●OUTPUT ASSIGN
●AIO A ASSIGN *1
●AIO B ASSIGN *2
ANC DATA EMBED
ANC EMBED LINE
●EMB1 SRC MODE
●EMB2 SRC MODE
●AES SRC MODE
●EMB1 POLARITY
●EMB2 POLARITY
●AES POLARITY
●ANALOG POLARITY
VIDEO OP
AUDIO OP LOGO SELECT KEYER SET
●Dolby AUX OUT A
*6*8
●Dolby DEC IN A *6*8
●Dolby DEC REF A *6*8
●Dolby DOWNMIX A *6*8
Dolby DEC GAIN A *6*8
●Dolby ENC INPUT A*8
●Dolby ENC SET A*8
●METADATA INPUT*8
◇LOUD MEASURE 1A *4
LOUD CTRL ENA1A *4
LOUD CTRL SET1A *4
LOUD CH ASGN1A *4
◇LOUD MEASURE 2A *4
LOUD CTRL ENA2A *4
LOUD CTRL SET2A *4
LOUD CH ASGN2A *4
●Dolby AUX OUT B *7*9
●Dolby DEC IN B *7*9
●Dolby DEC REF B *7*9
●Dolby DOWNMIX B *7*9
Dolby DEC GAIN B *7*9
●Dolby ENC INPUT B*9
●Dolby ENC SET B*9
●METADATA INPUT B*9
LOUD MEASURE 1B *5
LOUD CTRL ENA1B *5
LOUD CTRL SET1B *5
LOUD CH ASGN1B *5
◇LOUD MEASURE 2B *5
LOUD CTRL ENA2B *5
LOUD CTRL SET2B *5
LOUD CH ASGN2B *5
LOUD STANDARD *4 *5
VIDEO SYS
AUDIO SYS
●FS MODE SET
HD PHASE SET
SD PHASE SET
VIDEO POSITION
FREEZE SET
●ANC SET
ANC LOSS SET
WSS AFD ERROR
AUDIO GRP
TEST SIGNAL
●BY-PASS SETTING
SD LINE MASK
COMPOSITE SET1
●COMPOSITE SET2
●FADE IN/OUT
●DIGITAL AUDIO
●AUDIO ERR SENSE
●DIGITAL SILENCE
STATUS
OTHER
UNIT ALARM
VIDEO IN STATUS
VIDEO OP INPUT *1*2
VIDEO OUT STATUS
VIDEO OP OUTPUT *1*2
AUDIO IN DETECT1
AUDIO IN DETECT2
AUDIO OUTPUT1
AUDIO OUTPUT2
EMB1 IN AUDIO CH1~16
EMB2 IN AUDIO CH1~16
AES IN AUDIO CH1~8
ANALOG IN AUDIO CH1~4
SDI1/2 OUT AUDIO CH1~16
SDI3/4 OUT AUDIO CH1~16
AES OUT AUDIO CH1~8
ANALOG OUT AUDIO
CH1~4
Dolby OP A AUX *6*8
Dolby OP B AUX *7*9
AFD IN STATUS
ANC IN STATUS
ANC IN STATUS1~2
ANC OUT
S2016 OUT
VI OUT
WSS OUT
ANC OUT1
FS1/FS2 COPY
MU OPERATION
●CONTROL SETTING
FRONT OPERATION
FRONT PANEL SET
GPI SETTING
NETWORK INFO
UNIT Ver.
OPTION A Ver.
OPTION B Ver.
OTHER OPTION
SOFT OPTION1
SOFT OPTION2
VIDEO
AUDIO VIDEO menus AUDIO menus
9. LINK Settings
LINK setting menus shown with ⊚ in the menu list, allows you
to change values for FS1 and FS2 simultaneously.
Open a LINK setting menu, then press both the FS1/LOCK
and FS2/LOCK buttons simultaneously. One button turns on
and lights green, and the other blinks. “FS1” or “FS2” will be
displayed in the space a page number is usually displayed.
Changing settings by turning control knob (F1 to F4) for one
frame synchronizer will also change the same amount of
setting values for the other simultaneously.
①Select VIDEO or AUDIO by the VIDEO /AUDIO button.
Every press of the VIDEO/AUDIO button alternates the menu button
assignments between video and audio menus. The button indicators
light green when the buttons are accessible to video menus that are
indicated on the top row of each menu button. They light orange when
they are accessible to audio menus that are indicated on the bottom row
of each menu button.
②Press a menu button to select a menu group that includes the desired
menu.
③④Move to the desired menu using double-arrow and/or single-arrow
buttons.
The single-arrow buttons allow you to move between menus if the
selected menu button has multiple menu pages in the category. The
single-arrow button lights up when there are more menus to be accessed
in the direction. If the single-arrow button is unlit, the direction is not
accessible.
The double-arrow buttons allow you to go to menus indicated with  in
the menu list.
⑤The FS1/LOCK or FS2/LOCK button lights green as well as the selected
VIDEO button for menus in which settings can be set for FS1 and FS2
separately. If the FS1/LOCK button is pressed and lit green, settings for
FS1 are enabled. Settings for FS2 are enabled in the same manner.
⑥F1 to F4 control knobs allow you to change the value of respective lines.
Turn the operative control knob of an LED that is lit to change the value.
6. Menu Display
<Comments on the menu list>
Can be navigated to using double (up and down)
arrow buttons. ““ is not shown in the menu display.
⊚ Settings for FS1 and FS2 can be selected or
verified separately using the FS1 or FS2 button. ⊚
Can change settings for FS1 and FS2 simultaneously
in LINK mode. ““ and “⊚” are not shown in the
menu display.
●When changed in LIVE SAFE mode, single (up and
down) arrow buttons and the LED around the control
knob of which setting is changed blink confirming the
setting change.
*1 Shown if the FA-95AIO is installed in option slot A.
*2 Shown if the FA-95AIO is installed in option slot B.
*3 Hidden if the FA-95DACBL is installed.
*4 Shown if the FA-95ALA is installed in option slot A.
*5 Shown if the FA-95ALA is installed in option slot B.
*6 Shown if the FA-95D-D is installed in option slot A.
*7 Shown if the FA-95D-D is installed in option slot B.
*8 Shown if the FA-95DE-E is installed in option slot A.
*9 Shown if the FA-95DE-E is installed in option slot B.
7. Menu Operation
F1 F2 F3 F4
UNITY UNITY UNITY UNITY
Press the UNITY button to reset the value. The
indicator lights up orange.
POWER
ON
OFF
PS1/LOCK
PS2/LOCK
EVENT
VIDEOI N
GEN LOCL
REMOTE
AUDIOIN
FANALARM
DCPOWER F 1
F 2
F 3
F 4
F A - 9 5 2 0HD / SD FRAME SYNCHRONIZE R
DISPLAY F 1
UNITY
F 2
UNITY UNITY
F 3 F 4
UNITY
PROCESS
SDIAUDIO
MA PP I NG
VIDEO OP
AUDIO OP
C C
A V O CLIP
DELAY
VIDEO S YS
AUDIO S YS
AES AUDIO
CONV1
ANALOG
IN SEL
DOW NMIX
STATUS
OT HER
CONV 2
MAST ER
OUT SE L
MODE
VIDEO
AUDIO
①VIDEO/AUDIO button
VIDEO menus (lit green)
AUDIO menus (lit orange)
④Single-arrow button
Moves to the next menu.
Lights if a menu is accessible.
Goes off if no menu is accessible.
Also used to move to the next
menu item in a menu page.
②Menu button
Jumps to the first menu of
each menu group
indicated on respective
menu buttons.
③Double-arrow button
Jumps to the first menus
corresponding to each
menu button.
⑥F1 to 4
Changes corresponding
line menu parameters.
⑤ＦS1/LOCK, FS2/LOCK buttons
Selects FS1 or FS2.
F1 F2 F3 F4
UNITY UNITY UNITY UNITY
VIDEO PROC AMP 1
VIDEO LEVEL : 100.0%
CHROMA LEVEL: 100.0%
SETUP/BLACK : 0.0%
HUE : 0.0°
F 1
F 2
F 3
F 4
F A - 9 5 2 0HD / SD FRAME SYNCHRONI ZER
Parameter
Menu title
Value
Page number F1-F4 change setting values in corresponding
lines.