for Living 399-4002-4 User manual

4-PC CONVERSATION
DINING SET
Model No. 399-4002-4
Toll-free: 877-483-6759
IMPORTANT: Please read this manual carefully before beginning assembly of this product.
Keep this manual for future reference.
Assembly Instructions

4-PC CONVERSATION
DINING SET
Model No. 399-4002-4
Toll-free: 877-483-6759
IMPORTANT: Please read this manual carefully before beginning assembly of this product.
Keep this manual for future reference.
Assembly Instructions
- CHAIR

Parts List
3
Important Safety Instructions
4Model No. 399-4002-4
Table of Contents 2
Important Safety Instructions 2
Parts List 3
Assembly 4-7
Cleaning and Maintenance 8
Technical Data 8
Warranty 9
Warning! To reduce the risk of serious injury, read the following safety instructions before
assembling and using the product.
• This product is intended for domestic outdoor use only.
• The product should be placed on flat horizontal ground.
• Any assembly or maintenance of the product must be carried out by adults only.
• Arrange necessary manpower when assembling or moving the product.
• Some parts may contain sharp edges. Wear protective gloves if necessary.
• Keep children and pets away while setting up the product.
• Check all nuts and bolts periodically for tightness. When required, tighten them again.
• If the product will not be used for a long period (e.g. winter time), it should be stored in a clean,
dry environment.
• Do not light any fires below or near the product!
• Do not hang any weights on the frame.
Caution! Always keep children under close supervision while they are using or around this product.
Never leave children unattended.
IMPORTANT: RETAIN FOR FUTURE REFERENCE AND READ CAREFULLY.
CC
BB
AA
M6x15 Combination bolt&washer - 8
M6x55 Combination bolt& washer - 2
A
B
C
Hex key -1
D
Back frame - 1
Seat frame - 1
Left arm - 1
Right arm - 1
2Model No. 399-4002-4
Table of Contents
When itcomes to products for your home, it's essential they stand up to the realities of everyday family life.
Designed withyour family in mind, ForLivingTM products combine timeless style and family-friendly features.
Now you can focus on what's important—creating lasting memories with your family.

4 5
Model No. 399-4002-4
Assembly
Assembly
Step 1
Requires A, B, D, AA, CC
Attach theseat frame (B) totheright arm (D) and back frame (A).
Line up the bolt holes ontheseat frame (B) with the corresponding
bolt holes on the right arm (D) and back frame (A). InsertM6x15
combinationbolts and washers (AA) and lightly tighten thebolts
using the hex key (CC). Do not completely tightenuntil all
assembly is complete.
Step 2
Requires A, D, BB, CC
Attach right arm (D) toback frame (A) by lining upbolt holes on the right arm
(D) with correspondingbolt holes on back frame (A). Insert the M6x55 combination
bolt withwasher (BB) and lightly tighten using hex key (CC). Do notcompletely
tighten until all assembly is complete.
A
D
BB
A
B
D
AA AA
AA AA
Caution!
•Do not place the product underneath electrical lines.
•Keep children away during assembly.
This product contains small parts which can be swallowed by children.
•Keep fingers away from places where they can be pinched or trapped.
Let us help you!
DO NOT RETURN YOUR PRODUCT TO THE STORE. CALL US FIRST!
877-483-6759
If you have questions regarding your product, require warranty assistance,
or have damaged or missing parts, please call our customer service toll-free helpline.
Contact us for assistance; we’re here to help.
IMPORTANT: Please read and understand this manual before any assembly. Before beginning assembly of product,
make sure all parts are present. Compare parts with packaging contents list. If any part is missing, or if you have
any questions, contact the service centre at 877-483-6759 (toll free).
Needed for assembly:
2 people
Place all parts from the box in a cleared area and position them on the oor in front of you. Remove all packing
materials and place them back into the box. Do not disposeof the packing materials until assembly is complete.
Read each step carefully before beginning any assembly and make sure you understand each step. If you are
missing a part, please call our toll-free number for assistance at 877-483-6759.
•

6 7
Assembly
Step 3
Requires A, B, C, AA, CC
Attach the seat frame (B) to the left arm (C)and back frame(A). Line up the bolt
holes on the seat frame (B) with the corresponding bolt holes on theleft arm (C)
and back frame (A). Insert M6x15 combinationbolts and washers (AA) and lightly
tighten the bolts using the hex key (CC). Do not completely tighten until all
assembly is complete.
Step 4
Requires A, C, BB, CC
Attach left arm (C) to back frame (A) by lining up bolt holes ontheleft arm (C)
with corresponding bolt holes on back frame (A). Insert the M6x55
combination bolt with washer (BB) and lightly tighten usinghex key (CC).
Assembly
Model No. 399-4002-4
Step 5
Requires CC
Ensure all bolts are securely tightened using the hex key (CC). Turn the chair
the correct way up. Yourchair is now complete and ready to use.
A
B
AA AA
AA AA
C
BB
A
C

Warranty
8 9
Warranty
Model No. 399-4002-4
Cleaning & Maintenance
Warranty
-Wipe with adamp cloth. Use mild detergent and water, rinse with clearwater and pat out excess
moisture with a dry towel.
- Water should be cold tolukewarm, never more than 25°C (77°F).
- Air dry only.
•Do not use bleach, acid, or other abrasive cleaners on the frame parts.
•Steel components of garden accessories and furniture are treated with rust-inhibiting paint. However, due to
the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is a natural
process. To minimize this condition, it is recommended that care be taken when assembling and handling the
product, in order to prevent the paint from being scratched. If scratching or damage occurs, it is recommended
that the area be touched up immediately with rust-inhibiting paint, which is supplied with the product. Surface
rust can be removed easily using a very light application of common cooking oil. If surface oxidation (rusting)
occurs and no measures are taken to correct it, the oxidation may start dripping onto the assembly surface,
Caution!
•Check all bolts and nuts periodically for tightness, fastening them again as required.
•Disassemble the product in the reverse order of the assembly steps. Always
disassemble the product completely. A partially disassembled product is not stable
enough to resist wind and bad weather, and therefore can be damaged and/or cause
damage.
•Clean the product with mild soap and water. Rinse thoroughly, and wait until the product
is dry before reassembling it.
Dimensions (L x W x H) 23 x 28 1/2 x 31 7/8"
58.5 x 72.5 x 81 cm
This For Living product carries a one (1) year warranty against defects in workmanship and materials.
Trileaf Distribution agrees to replace the defective product free of charge within the stated warranty period,
when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear
or breakage due to misuse and/or abuse.
Product weight
Weight capacity
4.5 kg
9 lb 14 1/2oz
225 lbs
102 kg
Technical Data

4 PCCONVERSATION
DINING SET - LOVESEAT
Model No. 399-4002-4
Toll-free: 877-483-6759
IMPORTANT: Please read this manual carefully before beginning assembly of this product.
Keep this manual for future reference.
Assembly Instructions

Table of Contents
Important Safety Instructions
Table of Contents 2
Important Safety Instructions 2
Parts List 3
Assembly 4-7
Cleaning and Maintenance 8
Technical Data 8
Warranty 9
Warning! To reduce the risk of serious injury, read the following safety instructions before
assembling and using the product.
• This product is intended for domestic outdoor use only.
• The product should be placed on flat horizontal ground.
• Any assembly or maintenance of the product must be carried out by adults only.
• Arrange necessary manpower when assembling or moving the product.
• Some parts may contain sharp edges. Wear protective gloves if necessary.
• Keep children and pets away while setting up the product.
• Check all nuts and bolts periodically for tightness. When required, tighten them again.
• If the product will not be used for a long period (e.g. winter time), it should be stored in a clean,
dry environment.
• Do not light any fires below or near the product!
• Do not hang any weights on the frame.
Caution! Always keep children under close supervision while they are using or around this product.
Never leave children unattended.
IMPORTANT: RETAIN FOR FUTURE REFERENCE AND READ CAREFULLY.
CC
BB
AA
M6x15 Combination bolt&washer - 8
M6x55 Combination bolt& washer - 2
A
B
C
Hex key -1
D
Back frame - 1
Seat frame - 1
Left arm - 1
Right arm - 1
2Model No. 399-4002-43
Parts List
When it comes to products for your home, it's essential they stand up to the realities of
everyday family life. Designed with your family in mind, For LivingTM products combine
timeless style and family-friendly features. Now you can focus on what's important—creating
lasting memories with your family.

4 5
Model No. 399-4002-4
Assembly
Step 1
Requires :A, B, D, AA, CC
Attach theseat frame (B) totheright arm (D) and back frame (A). Line up the bolt holes
on theseat frame (B) with the corresponding bolt holes on the rightarm (D) and back
frame (A). Insert M6x15 combination bolts and washers (AA) and lightly tighten the
bolts usingthehex key (CC). Do not completely tightenuntil all assembly is complete.
Step 2
Requires : A, D, BB, CC
Attach back frame (A) to right arm (D). Line up the bolt holes on the back frame (A)
with the corresponding bolt holes on the right arm (D). Insert M6x55 combination bolts
and washers (BB) and lightly tighten the bolts using the hex key (CC). Donot
completely tightenuntil all assembly is complete.
Caution!
•Do not place the product underneath electrical lines.
•Keep children away during assembly.
This product contains small parts which can be swallowed by children.
•Keep fingers away from places where they can be pinched or trapped.
Let us help you!
DO NOT RETURN YOUR PRODUCT TO THE STORE. CALL US FIRST!
877-483-6759
If you have questions regarding your product, require warranty assistance,
or have damaged or missing parts, please call our customer service toll-free helpline.
Contact us for assistance; we’re here to help.
IMPORTANT: Please read and understand this manual before any assembly. Before beginning assembly of product,
make sure all parts are present. Compare parts with packaging contents list. If any part is missing, or if you have
any questions, contact the service centre at 877-483-6759 (toll free).
Needed for assembly:
2 people
Place all parts from the box in a cleared area and position them on the oor in front of you. Remove all packing
materials and place them back into the box. Do not disposeof the packing materials until assembly is complete.
Read each step carefully before beginning any assembly and make sure you understand each step. If you are
missing a part, please call our toll-free number for assistance at 877-483-6759.
•
A
B
D
AA
AA
AA
AA
A
D
BB
Assembly

6 7
Assembly
Step 3
Requires : A, B, C, AA, CC
Attach theseat frame (B) to the left arm (C)and back frame(A). Line up the bolt
holes on the seat frame (B) with the corresponding bolt holes on theleft arm (C)
and back frame (A). Insert M6x15 combinationbolts and washers (AA) and
lightly tighten the bolts using the hex key(CC). Do not completely tighten until
all assemby is complete.
Step 4
Requires : A, BB, CC
Attach left arm (C) to back frame (A) by lining up bolt holes ontheleft
arm (C) with corresponding bolt holes on back frame (A). Insert the M6x55
combination bolt with washer(BB) and lightly tighten using hex key (CC).
Assembly
Model No. 399-4002-4
Step 5
Requires : CC
Ensure all bolts are securely tightened using the hex key (CC). Turn the chair
the correct way up. Yourchair is now complete and ready to use.
A
B
AA AA AA AA
C
A
BB
C

Warranty
8 9
Warranty
Model No. 399-4002-4
Cleaning & MaintenanceTechnical Data
Dimensions (L x W x H) 42 1/2 x 28 1/2 x 31 7/8"
108 x 72.5 x 81 cm
Product weight
Weight capacity
7 kg
15 lb 7 oz
225 lb perseat
102 kg perseat
-Wipe with a damp cloth. Use mild detergent and water, rinsewith clear water and pat out excess
moisture with a dry towel.
- Water should be cold tolukewarm, never more than 25°C (77°F).
- Air dry only.
• Do not use bleach, acid, or other abrasive cleaners on the frame parts.
• Steel components of garden accessories and furniture are treated with rust-inhibiting paint. However, due to
the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is a natural
process. To minimize this condition, it is recommended that care be taken when assembling and handling the
product, in order to prevent the paint from being scratched. If scratching or damage occurs, it is recommended
that the area be touched up immediately with rust-inhibiting paint, which is supplied with the product. Surface
rust can be removed easily using a very light application of common cooking oil. If surface oxidation (rusting)
occurs and no measures are taken to correct it, the oxidation may start dripping onto the assembly surface,
Caution!
• Check all bolts and nuts periodically for tightness, fastening them again as required.
• Disassemble the product in the reverse order of the assembly steps. Always
disassemble the product completely. A partially disassembled product is not stable
enough to resist wind and bad weather, and therefore can be damaged and/or cause
damage.
• Clean the product with mild soap and water. Rinse thoroughly, and wait until the product
is dry before reassembling it.
This For Living product carries a one (1) year warranty against defects in workmanship and materials.
Trileaf Distribution agrees to replace the defective product free of charge within the stated warranty period,
when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear
or breakage due to misuse and/or abuse.

SLING4 PC CONVERSATION
SET- TABLE
Model No. 399-4002-4
Toll-free: 877-483-6759
IMPORTANT: Please read this manual carefully before beginning assembly of this product.
Keep this manual for future reference.
Assembly Instructions

3
Table of Contents
Important Safety Instructions
Table of Contents 3
Important Safety Instructions 3
Parts List 4
Assembly 6
Cleaning and Maintenance 8
Technical Data 8
Warranty 9
Warning! To reduce the risk of serious injury, read the following safety instructions before
assembling and using the product.
• This product is intended for domestic outdoor use only.
• The product should be placed on flat horizontal ground.
• Any assembly or maintenance of the product must be carried out by adults only.
• Arrange necessary manpower when assembling or moving the product.
• Some parts may contain sharp edges. Wear protective gloves if necessary.
• Keep children and pets away while setting up the product.
• Check all nuts and bolts periodically for tightness. When required, tighten them again.
• If the product will not be used for a long period (e.g. winter time), it should be stored in a clean,
dry environment.
• Do not light any fires inside or near the product!
• Do not hang any weights on the frame.
Caution! Always keep children under close supervision while they are using or around this product.
Never leave children unattended.
IMPORTANT: RETAIN FOR FUTURE REFERENCE, AND READ CAREFULLY.

Washer - 8
M6*35 Combination bolt & washer - 8
M6 nut - 8
Hex key -1
M6 wrench - 1
4 5
Model No. 399-4002-4
Part List
Assembly
Caution!
•Do not place the product underneath electrical lines.
•Keep children away during assembly.
This product contains small parts which can be swallowed by children.
•Keep fingers away from places where they can be pinched or trapped.
Let us help you!
DO NOT RETURN YOUR PRODUCT TO THE STORE. CALL US FIRST!
877-483-6759
If you have questions regarding your product, require warranty assistance,
or have damaged or missing parts, please call our customer service toll-free helpline.
Contact us for assistance; we’re here to help.
IMPORTANT: Please read and understand this manual before any assembly. Before beginning assembly of product,
make sure all parts are present. Compare parts with packaging contents list. If any part is missing, or if you have
any questions, contact the service centre at 877-483-6759 (toll free).
Needed for assembly:
Table top - 1
Leg connnecter - 1
Table leg - 4
Place all parts from the box ina cleared area and position them on the oor infront of you. Remove all packing
materials and place them back into the box. Do not dispose of the packing materials until assembly is complete.
Read each step carefully before beginning any assembly and make sure you understand each step. If you are
missing a part, pleasecall our toll-free number for assistance at 877-483-6759.
•A
B
C
AA
BB
CC
DD
EE
2 people

6 7
Assembly
Step 1
RequiresA, C
Place the table top (A) upside down on asoft surface. Insert the table legs (C) into
the corresponding holes on table top (A).
Step 3
Requires DD, EE
Ensure all bolts are securely tightened using the hex key(DD) and
M6 wrench (EE). Turn the table the correct way up. Your table is now
complete and ready to use.
Assembly
Step 2
Requires B, C, AA, BB, CC, DD, EE
Place the leg connector (B) between four table legs (C). Attach theleg connector (B) to
table leg (C) with M6*35mm combination bolt& washer (AA) ,washer (BB) & M6 nut (CC).
Lightly tighten the bolts using the hex key (DD) and M6 wrench (EE).
Model No. 399-4002-4
A
C
AA
AA
BB
BB
CC
CC
CB

Warranty
8 9
Cleaning & Maintenance
Warranty
Model No. 399-4002-4
Warranty
•For washing the fabric parts:
- Spread the fabric and use a soft bristle brush to clean.
-Always use a natural soap, never detergent.
-Water should be cold to lukewarm, never morethan 25°C (77°F).
-Air dry only, do not spin inwashing machine or hand squeeze.
•Do not use bleach, acid, or other abrasive cleaners on the canopies or frame parts.
•Steel components of garden accessories and furniture are treated with rust-inhibiting paint. However, due to
the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is a natural
process. To minimize this condition, it is recommended that care be taken when assembling and handling the
product, in order to prevent the paint from being scratched. If scratching or damage occurs, it is recommended
that the area be touched up immediately with rust-inhibiting paint, which is supplied with the product. Surface
rust can be removed easily using a very light application of common cooking oil. If surface oxidation (rusting)
occurs and no measures are taken to correct it, the oxidation may start dripping onto the assembly surface,
Caution!
•Check all bolts and nuts periodically for tightness, fastening them again as required.
•Disassemble the product in the reverse order of the assembly steps. Always
disassemble the product completely. A partially disassembled product is not stable
enough to resist wind and bad weather, and therefore can be damaged and/or cause
damage.
•Clean the product with mild soap and water. Rinse thoroughly, and wait until the product
is dry before reassembling it.
This For Living product carries a one (1) year warranty against defects in workmanship and materials.
Trileaf Distribution agrees to replace the defective product free of charge within the stated warr ,doirepytna
when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear
or breakage due to misuse and/or abuse.
Dimensions (L x W x H)
Product weight
Weight Capacity
35 x 19 x 18 in
89.5 x 49.5 x 45.5cm
8 kg
17.6 lbs
55 lbs
25 kg

N° de modèle : 399-4002-4
Numéro sans frais : 877 483-6759
IMPORTANT : Veuillez lire attentivement ce guide avant de procéder à l'assemblage de cet article, et
conservez-le aux fins de consultation ultérieure.
Instructions d'assemblage
ENSEMBLE DE CONVERSATION,
4 PIÈCES

N° de modèle : 399-4002-4
Numéro sans frais : 877 483-6759
IMPORTANT : Veuillez lire attentivement ce guide avant de procéder à l'assemblage de cet article, et
conservez-le aux fins de consultation ultérieure.
Instructions d'assemblage
ENSEMBLE DE CONVERSATION DE
4 PIÈCES -FAUTEUIL

3
Consignes de sécurité importantes
Table des matières 2
Consignes de sécurité importantes 2
Liste des pièces 3
Assemblage 4-7
Nettoyage et entretien
Garantie
Avertissement! Pour réduire tout risque de blessures graves, veuillez
lire les consignes de sécurité suivantes avantl’assemblage etl’utilisation de l'article.
Attention! Surveillez toujours de près les enfants pendant qu’ils utilisent l'article ou se trouvent à proximité.
IMPORTANT : LISEZ ATTENTIVEMENT CE GUIDE ET CONSERVEZ-LE AUX FINS DE
CONSULTATION ULTÉRIEURE.
Liste des pièces
Ne laissez jamais les enfants sans surveillance.
• Cet article est conçu pour une utilisation résidentielle à l’extérieur uniquement.
• Cet article doit être placé sur une surface plane et horizontale.
• Tout assemblage ou entretien de l'article doit être effectué par des adultes uniquement.
• Faites appel au nombre de personnes nécessaire pour assembler ou déplacer l'article.
• Certaines pièces peuvent présenter des bords tranchants. Portez des gants de protection au besoin.
• Véri ez tous les écrous et boulons régulièrement pour vous assurer qu’ils sont bien serrés. Serrez-les à
nouveau au besoin.
• Les enfants et les animaux doivent être tenus à l'écart pendant l'assemblage de cet article.
• Si l'article produit n’est pas utilisé pendant une longue période (pendant l'hiver, par exemple), il doit être rangé
dans un endroit propre et sec.
• N’allumez pas de feu en-dessousou à proximité de l'article!
• Ne suspendez aucun poids à l’armature.
8
8
9
CC
BB
AA
A
B
C
D
Boulon mixte M6x55 avec rondelle - 2
Boulon mixte M6x15 avec rondelle - 8
Clé hexagonale - 1
Armature de dossier - 1
Armature de siège - 1
Accoudoir gauche - 1
Accoudoir droit - 1
4Model No. 399-4002-4 2Model No. 399-4002-4
Table des matières
Lorsqu’il s’agit d’articles pour la maison, il est essentiel qu’ils puissent faire face aux réalités de la vie
quotidienne. Conçus en fonction de la famille, les articles For LivingMC allient un aspect traditionnel à des
caractéristiques de conception soucieuses des besoins de la famille. Vous pouvez maintenant vous concentrer
sur ce qui est important, soit de créer des souvenirs mémorables pour votre famille.

4 5
Assemblage Assemblage
N° de modèle : 399-4002-4
Étape 1
Requiert A, B, D, AA, CC
REMARQUE : Ne serrez
pas complètement
REMARQUE : Ne serrez pas complètement
Fixez l’armature de siège (B) à l’accoudoir droit (D) età l’armature de dossier (A).
Alignez les trous deboulondel’armature de siège (B) avecles trous deboulon
correspondants del’accoudoir droit (D) et de l’armature dedossier (A). Insérez
les boulons mixtes M6x15 avec rondelles (AA) et serrez légèrement les boulons à
l’aide de la clé hexagonale (CC). Neserrez pas complètement avant quel’assem-
blage soit terminé.
Étape 2
Requiert A, D, BB, CC
Fixez l’accoudoir droit (D) àl’armature de dossier (A) en alignantles trous de
boulon del’accoudoir droit (D) avec les trous de boulon correspondants de l’arma-
ture de dossier (A). Insérez le boulon mixte M6x55 avec rondelle (BB) et serrez
légèrement à l’aidede la clé hexagonale (CC). Ne serrez pas complètement avant
que l’assemblage soit terminé.
Laissez-nous vous aider!
.NISAGAMUAELCITRA'LRENRUOTERSAPENZELLIUEV
APPELEZ-NOUS D’ABORD!
877 483-6759
Si vous avez des questions concernant cet article,avez besoin d’une
assistance relative à la garantie ou avez des pièces endommagées ou
manquantes, veuillez communiquer avec notre service à la clientèle à la
ligne d’assistance gratuite. Veuillez nous contacter pour toute assistance,
nous sommes ici pour vous aider.
Ce qui est requis pour l’assemblage :
2 personnes
•Ne placez pas l'article sous des câbles électriques.
•Gardez les enfants éloignés pendant l’assemblage.
•Cet article contient des petites pièces que les enfants peuvent avaler.
• Éloignez les doigts des endroits où ils peuvent être pincés ou coincés.
Attention!
IMPORTANT : Veuillez lire et comprendre ce guide avant tout assemblage. Avant de procéder à l’assemblage de
l'article, assurez-vous qu’il ne manque aucune pièce. Comparez les pièces à la liste du contenu de l’emballage. Pour
toute pièce manquante ou pour toute question, veuillez communiquer avec le centre d’assistance au 877 483-6759
(sans frais).
Placez toutes les pièces du carton dans un endroit dégagé et positionnez-les sur le sol devant vous. Retirez tous les
matériaux d’emballage et replacez-les dans le carton. Ne vous débarrassez pas des matériaux d’emballage avant
d'avoir terminé l'assemblage. Lisez chaque étape avec soin avant de commencer l’assemblage et assurez- vous de
toutes les comprendre.
Si une pièce est manquante, veuillez téléphoner à notre numéro sans frais : 877 483-6759
A
D
BB
A
B
D
AA AA
AA AA