Force 10 65335 User manual

Ceramic Glass
Electric Galley
Ranges
OWNER’S MANUAL
Models # 65335, 65336, 75331, 75332
Read all instructions and warnings before operating.
Force 10 Manufacturing Corporation
Unit A – 19169 21st Ave
Surrey, BC
V3S 3M3
Tel: [phone]
Fax: [phone]
Website: www.force10.com

Page 1 of 8
ENG-0091.3
INTRODUCTION
Thank you for selecting the Force 10 Electric Galley Range. Your unit was carefully
inspected and tested at our factory. Please take the time to read this manual carefully;
many of its instructions are essential to the safe operation of your new Force 10
Electric Range
Because of the continuing refinement of our product designs, your Range may possess
features not discussed in the manual. We have tried to supply all the information you
might need, so please take time to read this manual before installing and using your
Range. Force 10 advises strongly against unauthorized modification of this product,
but we do encourage you to correct problems which may arise by under-taking the
simple repairs and maintenance described in this manual.
SAFETY & PRECAUTIONS
Read all Instructions before operating.
•Do not use your Range as a source of heat
•DO NOT TOUCH SURFACE UNITS OR AREAS NEAR UNITS - Heating
elements may be hot even though they are dark in color. Areas near surface units
may become hot enough to cause burns. During and after use, do not touch, or let
clothing or other flammable materials contact surface units or areas near units
until they have had sufficient time to cool.
•Before using your cook-top, check each time that the bottom of the
saucepan and the cooking zone are clean and dry.
•Lift up the sauce pans; sliding them across the cook-top can lead to
superficial scratches.
•Avoid peeling vegetables over the cook-top as this could lead to grit on
the surface and subsequent scratching.
•Use saucepans which are large enough to avoid spillage onto the cook-
top, especially if a saucepan contains any sugar as this can cause
irreparable damage to the glass ceramic.
•Keep the surface of the cook-top clear; above all do not keep plastic or
Aluminum packing on it which could melt and damage the cook-top.
If you are missing any parts or have questions regarding assembly,
performance or operation please contact Force 10 Manufacturing
Customer Service at 1-800-663-8515 or email at [email protected].

Page 2 of 8
ENG-0091.3
ELECTRICAL REQUIREMENTS
Model Voltage Freq. Surface Element
(each)
Oven or Broiler
Element
Maximum
65335 100 - 120 50 - 60 1200 W 10 A 1300 W 10.8 A 4900 W 41 A
75331 100 - 120 50 - 60 1200 W 10 A 1300 W 10.8 A 4900 W 41 A
65336 200 - 250 50 - 60 1200 W 5 A 1300 W 5.4 A 4900 W 20.4 A
75332 200 - 250 50 - 60 1200 W 5 A 1300 W 5.4 A 4900 W 20.4 A
Recommended Breaker Size
120 Volt units – 50A
240 Volt units – 30A
INSTALLATION
Unpacking
1. Remove all plastic coating before use.
2. Please copy the Model and Serial number of your unit into your manual. This is
located both on the box and the right side of the Range.
MODEL #_________________ SERIAL #___________________
Minimum Clearances to Adjacent Walls and Overhead Cabinets
No Clearance is required to an adjacent wall.
30" (762mm) minimum clearance between the top of the cooking surface and the
bottom of an unprotected wood or metal cabinet;
or
24” (610mm) minimum when bottom of wood or metal cabinet is protected by a
flame retardant heat shield.
To eliminate the risk of burns or fire by reaching over the heated surface, cabinet
storage space located above the surface units should be avoided. If cabinet storage is
to be provided, the risk can be reduced by installing a range hood that projects
horizontally a minimum of 5" beyond the bottom of the cabinets

Page 3 of 8
ENG-0091.3
65335 / 65336 Installation
Cutout Dimensions:
Width: 20.375” (518 mm)
Depth: 21” (534 mm)
Height: 21.75” (553 mm)
The opening between the cabinets should be 20.375” (518mm) wide, a minimum of
21” (534mm) deep and 21.75” (553mm) high for proper gimbal.
Mount a gimbal bracket on each side of the opening, positioning the bottom edge of
the bracket 3.75” (95mm) below the countertop, and the front side of the bracket 6.7”
(170mm) back from the front edge of the cabinets. This will position the stove so that
the top of the stove side is flush with the countertop and the stove cabinet will be
flush with the front surface of the adjacent cabinets.
Be sure to maintain a minimum 1” (25mm) open space behind the range, and at least
2” (51mm) of space below to allow the range to gimbal correctly.
Level each bracket and fasten with four #12 wood screws at least 1/2” in length.
Drill a 3/8” (10mm) hole on each side of the opening for the gimbal pin. Locate the
hole 0.47” (12mm) in from the face of the cabinet and 3.55” (90mm) below the
countertop. Fasten the gimbal lock plate over the hole using two # 8 wood screws at
least 3/8” in length.
Carefully lift the stove into position so that the gimbal pins snap into the brackets.
Gently pry the safety tabs of the bracket inward, toward the stove so that they
protrude over the gimbal pins.
Make sure the stove swings freely at least 15 degrees. Check to ensure the gimbal
lock pins slide into the hole you drilled.
75331 / 75332 Installation
Cutout Dimensions:
Width: 20.5” (521 mm)
Depth: 19” (483 mm)
Height: 21.5.” (546 mm)
The opening between the cabinets should be 20.5” (521mm) wide, a minimum of 19”
(483mm) deep and 21.5” (546mm) high.
Secure the stove into position by screwing the stove sides to the walls of the cut out.
The mounting holes can be accessed through (2) holes on both side of the stove
located just above the glass top. Use #6, 1” stainless steel wood screws.

Page 4 of 8
ENG-0091.3
Electrical connection
This product must be installed in accordance with national and local electric codes. It
must be supplied with the rated voltage and frequency and hardwired to it own branch
circuit, protected by an appropriate sized circuit breaker.
OPERATION
Theory
Glass ceramic cooktops require radiant heating elements. The principle of radiant
operation is based on the use of coiled heating wires mounted on an insulated support
fitted into a metal pan installed below the ceramic glass. The heating wires have an
average operating temperature of approximately 1000°C. A thermostat prevents the
temperature of the glass hob from exceeding 600°C. The heating wires and the
insulating support have been designed not to stop the infrared radiations upwards, but
reducing as much as possible side leakage and ensuring high efficiency. These heating
elements enable the appliance to reach the operating temperatures on the cooking
surface in a very short time.
Top Burners Operation
1. To turn on an element, rotate the control knob counter clockwise to the desired
setting.
2. A hot surface light located in the center of the cooktop will illuminate after a
slight delay.
3. To turn off the cooktop, rotate the knob to point upwards.
4. The hot surface light will turn off after the cooking surface has cooled.
USE COPPER WIRE ONLY

Page 5 of 8
ENG-0091.3
Oven/Broiler Operation
The oven and broiler are controlled by the same switch. To operate the oven, turn the
control knob clockwise and set the desired temperature. The oven LED will light,
indicating the unit is heating up. Once the oven is up to temperature, the LED light
will go out.
In order to operate the broiler, turn the control knob as far clockwise as possible. You
will feel a slight click as the control reaches the broiler setting. The oven LED will be
lit for the entire length of operation. Keep the door open about 3”, or to the last notch
on the handle. Remember, heat will be escaping from this gap, use caution.
When the broiler is activated, the oven element is disabled.
When cooking is complete, turn the control off. Until unit has cooled completely, use
caution when working around it.
Oven Door
Your Force 10 Electric Range is equipped with a slide away space saving door. To
open the door, lift up on the handle and pull towards you. The door will fold
underneath the oven.
CLEANING & MAINTENANCE
Ceramic Glass Cooktop Cleaning Instructions
All stain or deposit on the cook-top surface must be cleaned off quickly once the
cook-top has cooled down, before re-using the cook-top
Exception: In the case of sugar deposits, remove all residues before the cook-top
cools down (Be careful not to burn yourself!)
Important: Only
use cleaning
products that have
been specifically
designed for glass
ceramic cook-tops.
If the deposit is
minimal, simply
wipe off with a dry
cloth.
If the deposit is more
prominent, clean off
with a moist, soapy
sponge and rinse off.

Page 6 of 8
ENG-0091.3
Stainless Steel Cleaning Instructions
Do not use abrasive pads; they will scratch the surface
The basic rule of thumb is to use the mildest cleaning procedure that will do an
effective job. Always rinse thoroughly with clear water and dry completely. Frequent
cleaning will prolong the service life of stainless steel equipment and help maintain
the finish. Ordinary deposits of waste and fluids can usually be removed with soap
and water. More stubborn deposits or stuck on debris may require harder rubbing or
the use of commercial cleaning products acceptable for use on metal surfaces. When
using any cleansing agent, the rubbing should be in the direction of the polish lines or
"grain" of the metal.
Changing the light bulb
Your Force 10 oven is equipped with a light. The light bulb is located in the top right
hand corner of the oven and is screwed into the socket.
To remove the bulb, unscrew it clockwise. The replacement should be an A15 type -
40 watt frosted appliance bulb rated at the appropriate AC Voltage.
If the deposit does
not clean off easily,
use a non-abrasive
scratch pad and a
specially adapted
glass-ceramic
cleaning product.
If the deposit does
not clean off with
any of the above
mentioned methods,
use a razor blade
scraper, specially
designed for glass
ceramic cook-tops.
Having successfully
cleaned the cook-top,
apply a glass ceramic
cook-top conditioner
which will protect the
cook-top surface
against any future
stains, with a dry cloth
or equivalent.

Page 7 of 8
ENG-0091.3
PARTS
Description 65335
(120V)
65336
(240V)
75331
(120V)
75332
(240V)
LED Light 15212 15213 15212 15213
Control Knob 89248 89248 89248 89248
Oven Thermostat Control 89102 89102 89102 89102
Top Burner Control 89101 891011 89101 891011
Light Switch 87183 87183 87183 87183
Broiler Element 89107 89107A 89107 89107A
Oven Element 89106 89106A 89106 89106A
Burner Element 89131 89131A 89131 89131A
Oven Rack 306211 306211 555211 555211
Pot Holders 86000 86000 N/A N/A
TROUBLE SHOOTING GUIDE
PROBLEM CAUSE Solution______________
Unit will not turn on External Breaker has tripped Reset breaker
Hot Surface indicator stays on Element switch is bad Replace element
Oven works but top burners do
not come on
Internal thermal fuse has blown Replace wiring harness
Control knob does not move Burner control has seized Replace control
Light bulb does not stay on Light bulb is dead Change light bulb

Page 8 of 8
ENG-0091.3
SPECIFICATIONS
Part # 65335 65336 75331 75332
# of Top Burners 3 3 3 3
Output (watts
per burner) 1200 1200 1200 1200
Oven Yes Yes Yes Yes
Output (watts) 1300 1300 1300 1300
Broiler Yes Yes Yes Yes
Output (watts) 1300 1300 1300 1300
Voltage 100 - 120 200 - 250 100 - 120 200 - 250
Frequency (Hz) 50-60 50-60 50-60 50-60
Max Amps 41 20.4 41 20.4
Gimballed Yes Yes
Built-in Yes Yes
Width 20" 20" 21.5" 21.5"
Depth 20" 20" 19.75" 19.75"
Height 21.75" 21.75" 22.25" 22.25"
Light bulb style A15 - 40 W A15 - 40 W A15 - 40 W A15 - 40 W
Limited Warranty
Force 10 Manufacturing warranties this Electric Range to the original consumer to be
free from defective material(s) and workmanship while under normal use and service
for a period of (2) year.
During the warranty period, Force 10 Manufacturing will, at its option and without
charge, repair and/or replace but not remove or re-install the faulty product.
The purchaser will return defective products to the address stated below. No product
will be accepted by Force 10 Manufacturing without a Return Authorization Number.
Return of defective products must be accompanied by written details of the problems
and proof of purchase.
The buyer shall be responsible for shipping and insurance charges, if any, on the
products returned for repair under the terms of this warranty. Force 10 Manufacturing
will pay shipping of products returned to the buyer.
This limited warranty applies only to products that have been installed and used in
accordance to printed instructions of Force 10 Manufacturing and does not cover
improper use, vandalism, negligence or accidents.