Forcepoint V10000 G3 User manual

Quick Start Guide
Forcepoint V10000 G3
Web or Email Protection Appliance
See the Rack Installation Instructions included in the
Sliding Ready Rail kit.
Contact Forcepoint Technical Support if any items are missing.
Bezel (faceplate)
Power Cables (2) Ethernet Cables (4)
Accessory Kit
1
Sliding Ready Rail Kit
2
• Left Ready Rail
• Right Ready Rail
• Velcro Straps (2)
• Rack Installation Instructions
Cable Management Arm Kit
3
• Cable Management Arm
• Static Support Tray
• Status Indicator Cable
• Cable Tie Wraps
• CMA Installation Instructions
©2016 Forcepoint LLC. All rights reserved.
2
1
1. Connect to the appliance via serial port or KVM in order to access the command line interface for
initial configuration. Serial port settings are: 9600 baud, 8 bits, no parity.
2. Secure power cables using velcro straps and plug power
cables into an appropriate power source.
12
1
2
Serial Connection KVM Connection
5Connect Input Device
Rack Appliance
Power on the appliance and check the following indicators:
Contact Forcepoint Technical Support if any indicators are not
illuminated correctly.
Front
• Power button is illuminated.
• Hard drive LEDs are green.
Rear
• Power supply LEDs are green.
• LEDs for connected interfaces (NICs) are green.
• System status indicator (LED left of power supplies) is solid
blue.
6Power On Appliance
Please refer to the TRITON Appliances Getting Started guide for
more details.
Initial Configuration
Firstboot Script
• Configure security mode.
• Configure Appliance Controller interface (C).
• Configure NTP servers/system time.
Appliance Command Line
• Configure applicable network interfaces.
• Configure other settings as desired.
Web Mode
TRITON Manager
• Enter subscription key, update Master Database, configure
Network Agent, and configure policies in TRITON Manager.
• Requires Windows Server 2008 R2 or Windows Server 2012
or 2012 R2.
Content Gateway Manager (proxy)
• Configure user authentication and select protocols.
Email Mode
TRITON Manager
• Complete configuration wizard, enter subscription key, and
configure policies in the Email module. Configure email DLP
policies in the Data module.
• Requires Windows Server 2008 R2 or Windows Server 2012
or 2012 R2.
7Configuration Overview
Verify Contents
Plan your deployment before setting up the appliance. See the
back of this guide for a deployment overview and reference sheet.
Before you begin...
The appliance supports the following security modes:
3Determine Security Mode
Based on your subscription and deployment plan, determine the appropriate security mode for this
appliance.
• Web (TRITON AP-WEB)
• Email (TRITON AP-EMAIL)
Connect the appliance interfaces required by the security mode for this appliance. Cat 5E cables (or
better) are required. Do not use crossover network cables.
4Connect Network Cables
QSG420-100_RevF
Serial Cable

Deployment Reference SheetAppliance Deployment Overview
You can deploy one or more appliances on your network. The diagram below illustrates a basic appliance deployment. A
separate computer with Windows Server® 2008 R2 or Windows Server 2012 or 2012 R2 is required for running TRITON
Manager. See the TRITON Appliances Getting Started guide for details.
* P2 is optional and may be connected to a router or switch.
** Connect to bidirectional span, monitor, or mirror port if sending blocking information through N.
Internet
Firewall
Clients
Windows Server 2008 R2
Windows Server 2012 or 2012 R2
Router
*
** Switch
TRITON Manager
Email
Web SQL Server
Policy Server IP: IP Address:
Log Server IP: User Name:
Subscription Key: Password:
Log Server IP:
Authentication Mode:
Network Configuration
Network Agent Interface (N)
Content Gateway Interfaces (P1 & P2)
TRITON AP-EMAIL Interfaces (E1 & E2)
P1
E1
P2
E2
Appliance Controller Interface (C)
IP Address: Primary DNS:
Subnet Mask: Secondary DNS:
Default Gateway: Tertiary DNS:
IP Address: Primary DNS:
Subnet Mask: Secondary DNS:
Default Gateway: Tertiary DNS:
IP Address: Default Gateway:
IP Address: Default Gateway:
Subnet Mask: Primary DNS:
Subnet Mask: Primary DNS:
IP Address:
IP Address:
Secondary DNS:
Secondary DNS:
Subnet Mask:
Subnet Mask:
Tertiary DNS:
Above settings apply to P1 and P2
Tertiary DNS:
Above settings apply to E1 and E2
Support & Resources
Appliance Information
Interface C IP: Hostname:
admin is the default user name for the Appliance CLI, TRITON Manager, and Content Gateway Manager.
See the TRITON Appliances Getting Started guide for details.
Getting Started Guide
support.forcepoint.com/documentation
Online Support and Contact Information
support.forcepoint.com