Draytek Vigor2930 Series User manual

i
Vigor2930 Series
Dual-WAN Security Firewall
Quick Start Guide
Version: 1.0
Date: 2007/05/15

i
Copyright Information
Copyright
Declarations
Copyright 2007 All rights reserved. This publication contains information that is
protected by copyright. No part may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language without written
permission from the copyright holders.
Trademarks
The following trademarks are used in this document:
zMicrosoft is a registered trademark of Microsoft Corp.
zWindows, Windows 95, 98, Me, NT, 2000, XP and Explorer are
trademarks of Microsoft Corp.
zApple and Mac OS are registered trademarks of Apple Computer Inc.
zOther products may be trademarks or registered trademarks of their
respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
zRead the installation guide thoroughly before you set up the router.
zThe router is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the router
yourself.
zDo not place the router in a damp or humid place, e.g. a bathroom.
zDo not stack the routers.
zThe router should be used in a sheltered area, within a temperature range
of +5 to +40 Celsius.
zDo not expose the router to direct sunlight or other heat sources. The
housing and electronic components may be damaged by direct sunlight or
heat sources.
zDo not deploy the cable for LAN connection outdoor to prevent electronic
shock hazards.
zKeep the package out of reach of children.
zWhen you want to dispose of the router, please follow local regulations on
conservation of the environment.
Warranty
We warrant to the original end user (purchaser) that the router will be free from
any defects in workmanship or materials for a period of two (2) years from the
date of purchase from the dealer. Please keep your purchase receipt in a safe
place as it serves as proof of date of purchase. During the warranty period, and
upon proof of purchase, should the product have indications of failure due to
faulty workmanship and/or materials, we will, at our discretion, repair or replace
the defective products or components, without charge for either parts or labor, to
whatever extent we deem necessary tore-store the product to proper operating
condition. Any replacement will consist of a new or re-manufactured
functionally equivalent product of equal value, and will be offered solely at our
discretion. This warranty will not apply if the product is modified, misused,
tampered with, damaged by an act of God, or subjected to abnormal working
conditions. The warranty does not cover the bundled or licensed software of
other vendors. Defects which do not significantly affect the usability of the
product will not be covered by the warranty. We reserve the right to revise the
manual and online documentation and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.
Be a Registered
Owner Web registration is preferred. You can register your Vigor router via
http://www.draytek.com.
Firmware & Tools
Updates Due to the continuous evolution of DrayTek technology, all routers will be
regularly upgraded. Please consult the DrayTek web site for more information on
newest firmware, tools and documents.
http://www.draytek.com

ii
European Community Declarations
Manufacturer: DrayTek Corp.
Address: No. 26, Fu Shing Road, HuKou County, HsinChu Industrial Park, Hsin-Chu, Taiwan 303
Product: Vigor2930 Series Router
DrayTek Corp. declares that Vigor2930 Series of routers are in compliance with the following essential
requirements and other relevant provisions of R&TTE Directive 1999/5/EEC.
The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive
89/336/EEC by complying with the requirements set forth in EN55022/Class B and EN55024/Class B.
The product conforms to the requirements of Low Voltage (LVD) Directive 73/23/EEC by complying with
the requirements set forth in EN60950.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the use is encouraged to try to correct the interference
by one of the following measures:
zReorient or relocate the receiving antenna.
zIncrease the separation between the equipment and receiver.
zConnect the equipment into an outlet on a circuit different form that to which the receiver is
connected.
zConsult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired
operation.
Please visit www.draytek.com/about_us/Regulatory.php.

iii
T
Ta ab bl le e o of f C Co on nt te en nt ts s
1. Introduction........................................................................................................... 1
1.1 Panel Explanation ...................................................................................................................... 2
1.1.1 For Vigor2930 ............................................................................................................... 2
1.1.2 For Vigor2930n ............................................................................................................. 3
1.1.3 For Vigor2930Vn...........................................................................................................4
1.1.4 For Vigor2930VS...........................................................................................................5
1.1.5 For Vigor2930VSn......................................................................................................... 7
1.2 Package Content........................................................................................................................ 9
2. Installing Your Router..........................................................................................11
2.1 Hardware Installation.................................................................................................................11
2.2 ISDN Phone Adapter Installation.............................................................................................. 12
3. Configuring Web Pages ..................................................................................... 13
3.1 Basic Configuration.................................................................................................................. 13
3.2 Wireless Configuration............................................................................................................. 17
3.2.1 Basic Wireless LAN Concept...................................................................................... 17
3.2.2 General Setup.............................................................................................................17
3.2.3 Security Settings.........................................................................................................18
4. Trouble Shooting................................................................................................ 21
4.1 Checking If the Hardware Status Is OK or Not......................................................................... 21
4.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ...................... 22
4.3 Pinging the Router from Your Computer.................................................................................. 24
4.4 Checking If the ISP Settings are OK or Not............................................................................. 25
4.5 Backing to Factory Default Setting If Necessary...................................................................... 27
4.6 Contacting Your Dealer ............................................................................................................ 28

1
1
1. . I In nt tr ro od du uc ct ti io on n
Vigor2930 is a broadband router with dual-WAN interface. It provides policy-based
load-balance, fail-over and BOD (Bandwidth on Demand), also it integrates IP layer QoS,
NAT session/bandwidth management to help users control works well with large
bandwidth.
By adopting hardware-based VPN platform, hardware encryption of AES/DES/3DS and
hardware key hash of SHA-1/MD5, the router increases the performance of VPN greatly,
and offers several protocols (such as IPSec/PPTP/L2TP) with up to 100 VPN tunnels.
The Object-based design used in SPI (Stateful Packet Inspection) firewall allows users to
set firewall policy with ease. CSM (Content Security Management) provides users control
and management in IM (Instant Messenger) and P2P (Peer to Peer) more efficiency than
before. By the way, DoS/DDoS prevention and URL/Web content filter strengthen the
security outside and control inside.
Vigor2930 V models provide twin analogue phone ports. S models support ISDN ports.
Combining the characteristics of V and S models can offer two ISDN ports additionally
besides analogue phone ports. ISDN S0 port is dedicated for ISDN phone; the other ISDN
port is configurable for ISDN line and phone. It supports multiple SIP registrars with
highly flexible configuration and call handling options.
D
De ef fi in ni it ti io on ns s f fo or r I IS SD DN N P Po or rt ts s
Below shows the names that displayed on front panel of the device and the WEB UI of
this device.
ISDN TE (Terminal Equipment) means an interface for transmitting analog signal
through Internet between Switching and router. Such interface is also named with ISDN
S0 extern in Germany.
ISDN NT (Network Terminator) is a port that used to connect general phone. Such
interface is also named with ISDN S0 intern in Germany.
The ISDN S0 1 port on Vigor2930 series is fixed to connect phone forever and the LED
on the connecter will light orange always. However ISDN S0 2 port on this device is
configurable for connecting phone or accessing Internet according to the settings that you
adjust on WEB UI (please refer to VoIP>>Phone Setting for detailed information).
Warning: When the orange LED lights (means ISDN NT mode), the ISDN
port can be used to connect phone only. Wrong ISDN connection might cause
severe damage on your device.

2
1
1. .1 1 P Pa an ne el l E Ex xp pl la an na at ti io on n
1
1. .1 1. .1 1 F Fo or r V Vi ig go or r2 29 93 30 0
LED Status Explanation
Blinking The router is powered on and running normally.ACT (Activity) Off The router is powered off.
On The DoS/DDoS function is active.DoS Blinking It will blink while deleting an attack.
CSM On The profile of CSM (Content Security
Management) for IM/P2P application is active. (It
is enabled from Objects Setting >> CSM Profile).
CPA (Content Portal Authority) On The Web Content Filter is active. (It is enabled
from Firewall >> Web Content Filter Setup)
On The WAN1 or WAN2 connection is ready.WAN1/2 Blinking It will blink while transmitting data.
On The router is managed (handled) by Telnet.MGMT Blinking It will blink while being managed by IE browser.
VPN On The VPN tunnel is active.
QoS On The QoS function is active.
LED on Connector
On The port is connected.
Off The port is disconnected.
Left LED
(Green)
Blinking The data is transmitting.
On The port is connected with 100Mbps.
WAN 1/2
Right LED
(Green) Off The port is disconnected with 10Mbps.
On The port is connected.
Off The port is disconnected.
Left LED
(Green)
Blinking The data is transmitting.
On The port is connected with 100Mbps.
LAN 1/2/3/4
Right LED
(Green) Off The port is disconnected with 10Mbps.
Interface Description
Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking).
Press the hole and keep for more than 5 seconds. When you see the ACT LED
begins to blink rapidly than usual, release the button. Then the router will restart
with the factory default configuration.
Restart Restart the router forcefully.
WAN(1/2) Connecters for remote networked devices.
LAN (1-4) Connecters for local networked devices.
PWR Connecter for a power adapter.
ON/OFF Power Switch.

3
1
1. .1 1. .2 2 F Fo or r V Vi ig go or r2 29 93 30 0n n
LED Status Explanation
Blinking The router is powered on and running normally.ACT (Activity) Off The router is powered off.
DoS On The DoS/DDoS function is active.
Blinking It will blink while deleting an attack.
CSM On The profile of CSM (Content Security
Management) for IM/P2P application is active. (It
is enabled from Objects Setting >> CSM Profile).
On Wireless access point is ready. WLAN Blinking It will blink while wireless traffic goes through.
On The WAN1 or WAN2 connection is ready.WAN1/2 Blinking It will blink while transmitting data.
On The router is managed (handled) by Telnet.MGMT Blinking It will blink while being managed by IE browser.
VPN On The VPN tunnel is active.
QoS On The QoS function is active.
LED on Connector
On The port is connected.
Off The port is disconnected.
Left LED
(Green)
Blinking The data is transmitting.
On The port is connected with 100Mbps.
WAN 1/2
Right LED
(Green) Off The port is disconnected with 10Mbps.
On The port is connected.
Off The port is disconnected.
Left LED
(Green)
Blinking The data is transmitting.
On The port is connected with 100Mbps.
LAN 1/2/3/4
Right LED
(Green) Off The port is disconnected with 10Mbps.
Interface Description
Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking).
Press the hole and keep for more than 5 seconds. When you see the ACT LED
begins to blink rapidly than usual, release the button. Then the router will restart
with the factory default configuration.
Restart Restart the router forcefully.
Phone (1/2) Connecters for PSTN phones.
WAN (1/2) Connecters for remote networked devices.
LAN (1-4) Connecters for local networked devices.
PWR Connecter for a power adapter.
ON/OFF Power Switch.

4
1
1. .1 1. .3 3 F Fo or r V Vi ig go or r2 29 93 30 0V Vn n
LED Status Explanation
Blinking The router is powered on and running normally.ACT (Activity) Off The router is powered off.
On The DoS/DDoS function is active.DoS Blinking It will blink while deleting an attack.
CSM On The profile of CSM (Content Security
Management) for IM/P2P application is active. (It
is enabled from Objects Setting >> CSM Profile).
On Wireless access point is ready. WLAN Blinking It will blink while wireless traffic goes through.
On The WAN1 or WAN2 connection is ready.WAN1/2 Blinking It will blink while transmitting data.
On The router is managed (handled) by Telnet.MGMT Blinking It will blink while being managed by IE browser.
On The phone connected to this port is off-hook.
Off The phone connected to this port is on-hook.
Phone 1/2
Blinking A phone call comes.
LED on Connector
On The port is connected.
Off The port is disconnected.
Left LED
(Green)
Blinking The data is transmitting.
On The port is connected with 100Mbps.
WAN 1/2
Right LED
(Green) Off The port is disconnected with 10Mbps.
On The port is connected.
Off The port is disconnected.
Left LED
(Green)
Blinking The data is transmitting.
On The port is connected with 100Mbps.
LAN 1/2/3/4
Right LED
(Green) Off The port is disconnected with 10Mbps.
Interface Description
Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking).
Press the hole and keep for more than 5 seconds. When you see the ACT LED
begins to blink rapidly than usual, release the button. Then the router will restart
with the factory default configuration.
Restart Restart the router forcefully.
Phone (1/2) Connecters for PSTN phones.
WAN (1/2) Connecters for remote networked devices.
LAN (1-4) Connecters for local networked devices.
PWR Connecter for a power adapter.
ON/OFF Power Switch.

5
1
1. .1 1. .4 4 F Fo or r V Vi ig go or r2 29 93 30 0V VS S
LED Status Explanation
Blinking The router is powered on and running normally.ACT (Activity) Off The router is powered off.
On The DoS/DDoS function is active.DoS Blinking It will blink while deleting an attack.
CSM On The profile of CSM (Content Security
Management) for IM/P2P application is active. (It
is enabled from Objects Setting >> CSM Profile).
CPA (Content Portal Authority) On The Web Content Filter is active. (It is enabled
from Firewall >> Web Content Filter Setup)
On The WAN1 or WAN2 connection is ready.WAN1/2 Blinking It will blink while transmitting data.
On The router is managed (handled) by Telnet.MGMT Blinking It will blink while being managed by IE browser.
On The phone connected to this port is off-hook.
Off The phone connected to this port is on-hook.
Phone 1/2
Blinking A phone call comes.
LED on Connector
On ISDN NT (ISDN S0 intern) mode is active and an
ISDN phone adapter is connected.
Left LED
(Orange) Blinking ISDN NT (ISDN S0 intern) mode is active and an
ISDN phone adapter is not connected.
On A phone has been connected. If not, green LED will
be off.
ISDN S0 1
Right LED
(Green) Blinking An ISDN phone is off-hook or a phone call comes.
On ISDN NT (ISDN S0 intern) mode is active
configured from VoIP>>Phone Settings and an
ISDN phone adapter is connected.
Blinking ISDN NT (ISDN S0 intern) mode configured from
VoIP>>Phone Settings is active and an ISDN
phone adapter is not connected.
Left LED
(Orange)
Off It means ISDN TE mode is active which is
configured from VoIP>>Phone Settings.
On A phone adapter with phone set has been connected
(ISDN S0 intern mode) or ISDN line has been
connected (ISDN S0 extern mode). It will be off if
there is nothing connected.
ISDN S0 2
Right LED
(Green)
Blinking In ISDN NT (ISDN S0 intern) mode, it means an
ISDN phone is off-hook or a phone call comes.
In ISDN TE mode, it means data, fax or voice
(phone call) is transmitting.
On The port is connected.
Off The port is disconnected.
Left LED
(Green)
Blinking The data is transmitting.
On The port is connected with 100Mbps.
WAN 1/2
Right LED
(Green) Off The port is disconnected with 10Mbps.
Left LED On The port is connected.

6
Off The port is disconnected.
(Green) Blinking The data is transmitting.
On The port is connected with 100Mbps.Right LED
(Green) Off The port is disconnected with 10Mbps.
Interface Description
Factory Reset Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for
more than 5 seconds. When you see the ACT LED begins to blink rapidly than
usual, release the button. Then the router will restart with the factory default
configuration.
Restart Restart the router forcefully.
Phone (1/2) Connecters for PSTN phones.
ISDN S0 1 Connecter for ISDN phone(s) only via ISDN phone adapter. Do not connect any
other device to such port or connect ISDN line, otherwise the router might be
damaged.
ISDN S0 2 Connecter for ISDN line or ISDN phone adapter in particular condition. Refer to
section 2.2 for more details.
WAN (1/2) Connecters for remote networked devices.
LAN (1-4) Connecters for local networked devices.
PWR Connecter for a power adapter.
ON/OFF Power Switch.

7
1
1. .1 1. .5 5 F Fo or r V Vi ig go or r2 29 93 30 0V VS Sn n
LED Status Explanation
Blinking The router is powered on and running normally.ACT (Activity) Off The router is powered off.
On The DoS/DDoS function is active.DoS Blinking It will blink while deleting an attack.
CSM On The profile of CSM (Content Security
Management) for IM/P2P application is active. (It
is enabled from Objects Setting >> CSM Profile).
On Wireless access point is ready. WLAN Blinking It will blink while wireless traffic goes through.
On The WAN1 or WAN2 connection is ready.WAN1/2 Blinking It will blink while transmitting data.
On The router is managed (handled) by Telnet.MGMT Blinking It will blink while being managed by IE browser.
On The phone connected to this port is off-hook.
Off The phone connected to this port is on-hook.
Phone 1/2
Blinking A phone call comes.
LED on Connector
On ISDN NT (ISDN S0 intern) mode is active and an
ISDN phone adapter is connected.
Left LED
(Orange) Blinking ISDN NT (ISDN S0 intern) mode is active and an
ISDN phone adapter is not connected.
On A phone has been connected. If not, green LED will
be off.
ISDN S0 1
Right LED
(Green) Blinking An ISDN phone is off-hook or a phone call comes.
On ISDN NT (ISDN S0 intern) mode is active
configured from VoIP>>Phone Settings and an
ISDN phone adapter is connected.
Blinking ISDN NT (ISDN S0 intern) mode configured from
VoIP>>Phone Settings is active and an ISDN
phone adapter is not connected.
Left LED
(Orange)
Off It means ISDN TE mode is active which is
configured from VoIP>>Phone Settings.
On A phone adapter with phone set has been connected
(ISDN S0 intern mode) or ISDN line has been
connected (ISDN S0 extern mode). It will be off if
there is nothing connected.
ISDN S0 2
Right LED
(Green)
Blinking In ISDN NT (ISDN S0 intern) mode, it means an
ISDN phone is off-hook or a phone call comes.
In ISDN TE mode, it means data, fax or voice
(phone call) is transmitting.
On The port is connected.
Off The port is disconnected.
Left LED
(Green)
Blinking The data is transmitting.
On The port is connected with 100Mbps.
WAN 1/2
Right LED
(Green) Off The port is disconnected with 10Mbps.
On The port is connected.
LAN 1/2/3/4 Left LED
(Green) Off The port is disconnected.

8
Blinking The data is transmitting.
On The port is connected with 100Mbps.Right LED
(Green) Off The port is disconnected with 10Mbps.
Interface Description
Factory Reset Restore the default settings.
Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for
more than 5 seconds. When you see the ACT LED begins to blink rapidly than
usual, release the button. Then the router will restart with the factory default
configuration.
Restart Restart the router forcefully.
Phone (1/2) Connecters for PSTN phones.
ISDN S0 1 Connecter for ISDN phone(s) only via ISDN phone adapter. Do not connect any
other device to such port or connect ISDN line, otherwise the router might be
damaged.
ISDN S0 2 Connecter for ISDN line or ISDN phone adapter in particular condition. Refer to
section 2.2 for more details.
WAN (1/2) Connecters for remote networked devices.
LAN (1-4) Connecters for local networked devices.
PWR Connecter for a power adapter.
ON/OFF Power Switch.

9
1
1. .2 2 P Pa ac ck ka ag ge e C Co on nt te en nt t
nQuick Start Guide oCD
pRJ-45 Cable (Ethernet) qRJ-45 to RJ-45 Cable for Smodels
rISDN Phone Adapter
sThe type of the power adapter depends on the country that the router will be installed:
UK-type Power Adapter EU-type Power Adapter
USA/Taiwan-type Power Adapter AU/NZ-type Power Adapter
* The maximum power consumption is 17-23 Watt.

10
This page is left blank.

11
2
2. . I In ns st ta al ll li in ng g Y Yo ou ur r R Ro ou ut te er r
This section will guide you to install the router through hardware connection and
configure the router’s settings through web browser.
2
2. .1 1 H Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n
Before starting to configure the router, you have to connect your devices correctly.
1. Connect the cable Modem/DSL Modem/Media Converter to any WAN port of router
with Ethernet cable (RJ-45). The WAN1/WAN2 LED (Left or Right) will light up
according to the speed (100 or 10) of the device that it connected.
2. Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router
and the other end of the cable (RJ-45) into the Ethernet port on your computer. The
LAN LED (Left or Right) will light up according to the speed (100 or 10) of the
device that it connected.
3. Connect the telephone sets with phone lines (for using VoIP function). For the model
without phone ports, skip this step.
4. Connect one end of the power adapter to the router’s power port on the rear panel,
and the other side into a wall outlet.
5. Power on the device by pressing down the power switch on the rear panel.
6. The system starts to initiate. After completing the system test, the ACT LED will
light up and start blinking.
(For the detailed information of LED status, please refer to section 1.1.)
Caution: Each of the Phone ports can be connected to an analog phone only. Do not
connect the phone ports to the telephone wall jack. Such connection might damage your
router.

12
2
2. .2 2 I IS SD DN N P Ph ho on ne e A Ad da ap pt te er r I In ns st ta al ll la at ti io on n
Such information is provided for Vigor2930 S models (e.g., Vigor2930VS).
ISDN S0 1 is always fixed to connect ISDN phone. However, ISDN S0 2 is configurable
as NT (ISDN S0 intern) or TE (ISDN S0 extern) mode. When the user configures ISDN
S0 2 as NT mode in VoIP>> Phone Settings, the orange LED will light on to indicate
ISDN2-S0 is selected. And by using ISDN phone adapters (coming from the router
package), the user can connect several phones to Vigor2930VS for communication.
Refer to the following figure for reference.
Yet, if the user configures ISDN S0 2 as TE Mode in VoIP>> Phone Settings, the green
LED will light on to indicate ISDN2-TE is selected. Then, the port is specified for ISDN
line only. Refer to the following figure for reference.

13
3
3. . C Co on nf fi ig gu ur ri in ng g W We eb b P Pa ag ge es s
To access Internet, please finish basic configuration after completing the hardware
installation.
3
3. .1 1 B Ba as si ic c C Co on nf fi ig gu ur ra at ti io on n
The Quick Start Wizard is designed for you to easily set up your router for Internet
access. You can directly access the Quick Start Wizard via Web Configurator.
1. Make sure your PC connects to the router correctly.
Notice: You may either simply set up your computer to get IP dynamically
from the router or set up the IP address of the computer to be the same
subnet as the default IP address of Vigor router 192.168.1.1. For the
detailed information, please refer to the later section - Trouble Shooting of
the guide.
2. Open a web browser on your PC and type http://192.168.1.1. A pop-up window will
open to ask for username and password. Do not type any word on the window and
click OK for next screen.
Notice: If you fail to access to the web configuration, please go to “Trouble
Shooting” for detecting and solving your problem.
3. Now, the Main Screen will pop up. Click Quick Start Wizard.
Note: The home page will change slightly in accordance with the router you have.

14
4. Enter the login password on the field of New Password and retype it on the field of
Retype New Password. Then click Next to continue.
5. On the next page as shown below, please select the WAN interface that you use.
Choose Auto negotiation as the physical type for your router. Then click Next for
next step.
6. On the next page as shown below, please select the appropriate Internet access type
according to the information from your ISP. For example, you should select PPPoE
mode if the ISP provides you PPPoE interface. Then click Next for next step.

15
PPPoE: if you click PPPoE or PPPoA as the protocol, please manually enter the
Username/Password provided by your ISP. Then click Next.
PPTP: if you click PPTP, you will get the following page. Please type in all the
information originally provided by your ISP. Then click Next for next step.
Static IP: if you click Static IP, you will get the following page. Please type in the IP
address information originally provided by your ISP. Then click Next for next step.

16
DHCP: if you click DHCP, you will get the following page. Simply click Next to
continue.
7. Now you can see the following screen. It indicates that the setup is complete.
Different types of connection modes will have different summary. Click Finish and
then restart the router. Afterward, you will enjoy surfing on the Internet.