Fortinet FortiSwitch-80-PoE User manual

QuickStart Guide
FortiSwitch-80-PoE
LED Description
Package Contents
LED State Description
PWR Green The unit is ready and has AC power.
Off The power switch is turned off or the power supply is not connected.
PoE Max Red The power budget has exceeded.
Off Power budget has not exceeded. This is the desired condition.
PoE LED port (1–4)
Green Indicates the port is sending PoE to a powered device.
Red Indicates there is a problem with the power feed to the port.
Off Indicates the PoE is not sourced due to either an issue with the wiring, an incompatible
powered device, or the connected device does not need PoE.
Port Link/Act/Speed LED
(1–8)
Green The interface is connected at Gigabit rate.
Amber The interface is connected at 10/100 Mb rate.
Off The interface is not connected.
Flashing Indicates trafc activity.
Step 1. Unpacking
Provides 62 Watts of dedicated PoE power
Open the shipping carton and carefully unpack its contents. The carton should contain the following items:
• One FS-80-PoE Switch
• One 90W AC-DC power adapter
• One country specic AC power cord
• One Quick Installation Guide (QSG)
• Four rubber feet to be used for shock cushioning
• Warranty Card
If any item is found missing or damaged, please contact your local reseller for replacement.
FortiSwitch-80-PoE User’s Guide is available from the Fortinet website at http://docs.fortinet.com/.
FortiGate-30B
Copyright 2010 Fortinet Incorporated. All rights reserved.
Trademarks
QuickStart Guide
FMC-XG2
ACTIVE
SERVICE
1 (SFP +) 2 (SFP +)
REGISTER
Power adapter
FS-80-PoE switch Power supply

Setup the FortiSwitch-80-PoE using the following steps:
• The surface must support at least 1.5 Kg for the switch.
• The power outlet should be within 1.82 meters (6 feet) of the switch.
• Visually inspect the DC power jack and make sure that it is fully secured to the power adapter.
• Make sure there is adequate ventilation around the switch for proper heat dissipation.
• Do not place heavy objects on the switch.
Step 2. Installing
© Copyright 2010 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks
of their respective holders.
05 November 2010
11-100-0133349-20101112
Step 3. Connecting
Step 4. Powering on
Connect the switch to the power outlet and then turn the power switch on to activate the switch. The power switch is located at the back of the unit.
The FS-80-PoE can supply power to a PoE capable device over an existing Ethernet cable. If a device is not compatible, or does not operate on
PoE, then the port will not source power to this device. This feature allows users to freely and safely mix legacy and Power over LAN compatible
devices on their network.
The FS-80-PoE supports 8 10/100/1000M Ethernet ports. Ports 1 – 4 supply PoE automatically when connected to a 802.3af compatible device.
Ports 5 – 8 do not provide PoE, and are best suited for uplink ports, PCs and printers. These ports automatically detect and operate in half and full
duplex mode.
The FS-80-PoE provides auto MDI-II or MDI-X cable selection for easy connection using standard or crossover RJ45 cables.
Note : It is important that the PoE is used indoors only. Ensure that Ethernet cable carrying PoE power does not route outside of the building.
Ports 1 - 4 4 × 10/100/1000 Mbps Auto-MDIX RJ45 ports with
POE enabled
Port 5 - 8 4 × 10/100/1000 Mbps Auto-MDIX RJ45 ports