FOS Technologies FOS TV FRESNEL WW L005614 User manual

L005614 FOS TV FRESNEL WW USER MANUAL L005614 FOS TV FRESNEL WW USER MANUAL
FOS TV FRESNEL WW
L005614
CE RoHS
User Manual
Please read this user manual before using this product！
Keep it for further reference!

L005614 FOS TV FRESNEL WW USER MANUAL L005614 FOS TV FRESNEL WW USER MANUAL

L005614 FOS TV FRESNEL WW USER MANUAL L005614 FOS TV FRESNEL WW USER MANUAL
Caution
Unqualified person involved with installation, operation and maintenance of this
device is prohibited
If any above mentioned problem happened, or unknown problem happened, please
contact manufacturer or distributor for assistance.
Innovation, Quality, Performance, Achieving Users’Value!
INDEX
ⅠPRODUCT MAIN FEATURES ......................................... 01
ⅡOVERVIEW AND DIMENSIONS.....................................02
ⅢSAFETY INFORMATION ................................................02
ⅣPOWER CONNECTION ..................................................03
ⅤCONTROL PANNEL ....................................................... 05
ⅥDMX PROTOCOL ...........................................................06
ⅦCOMMON INSTRUCTION ..............................................06
ⅧTECHNICAL SPECIFICATION........................................ 07
ⅨAPPENDIX ....................................................................09
10

L005614 FOS TV FRESNEL WW USER MANUAL L005614 FOS TV FRESNEL WW USER MANUAL
·Light visor: optional
·IP rating: IP20
·Housing material: aluminum alloy
·Working temperature: -25~40centigrad degree
ⅨAPPENDIX
Problem and solution
Problem
Reason
Resolution
Device not work
No power
AC100-240V, 50/60Hz
Check the power connection, and
make sure device connect the mains
in well condition.
Check if the fuse is good.
LED Bulb is off
LED bulb damaged
Replacing LED bulb
LED drive board damaged
Replacing LED drive board
Temperature switch damaged
Replacing temperature switch
Fans not work
Fans damaged
Replacing fans
09

L005614 FOS TV FRESNEL WW USER MANUAL L005614 FOS TV FRESNEL WW USER MANUAL
If you want to set the ID address for the light, press MENU until the display shows d001 ,
then press UP or DOWN button to set the address value, press ENTER to confirm the
setting;
Open or close the strobe function: press MENU button until the display shows d001 , then
press MENU button four times until the display 2nd, 3rd, 4th number shows --1 , the
strobe function will open, then press the ENTER to confirm the setting. When the display
2nd, 3rd, 4th number shows --0 , the strobe function will close, press ENTER button to
confirm the setting;
This light is only for indoor use, when you install it by hanging, please use the safety cable
to ensure the safety.
If you have any questions, please contact with our sales manager.
ⅧTECHNICAL SPECIFICATION
·Input power: AC100~240V, 50/60Hz
·Power consumption: 250W
·Light sources: 100W brand COB LED Lamps
·LED lifespan: 50,000hours
·Dimmer: 0~100%, 0-15% smoothly dimmer
·Beam angle: 15-60degree
·Color rendering index: ≥92Ra
·Color temperature: 3200K to 6500K optional
·Control mode: DMX-512
·DMX channel: 1CH
·Focus: manual focus adjustable
Thank you for using our product! Please read this manual carefully and completely. For
technical reference in future, please keep this user manual well. This user manual contains
all installation and operation information of this LED Studio Focalize Light, it’s very useful
for user to install and operate the light. Please strictly abide by the relevant instruction for
the installation and operation.
This light has very beautiful appearance. Based on the LED Film and Television Flat Light
Technology, using high brightness COB LED chips beads matrix arrangement of large area,
through the whole aluminum shell to realize heat dissipation naturally, we have designed
this light. This light has high brightness, good head dissipation, ultra-quiet and other
features. It can satisfy the requirement of indoor movie filming for the lighting layout. It is
a good substitute of the traditional Fresnel spot light, which is very suitable for the studio
room, TV station, Meeting room, stage, show and other entertainment places.
This light meets the following criteria:
GB7000.1-2007/IEC60598-1:2003
GB7000.217-2008/IEC60598-2-17:1984+A2:1990
ⅠPRODUCT MAIN FEATURES
The light’s lighting function is controlled by DMX-512, very convenient;
Using international standard (1990) DMX single, digital control panel display;
With 1 DMX channel as dimmer; (Strobe channel closed)
Dimmer range: 0~100%, 0~15% dimmer smoothly;
CRI more than 92, 3000~5600K color temperature optional, light effective distance is
12~17 meters;
Cast aluminum radiator, equips copper tube radiator, no need fan cooling, realize the silent,
01
08

L005614 FOS TV FRESNEL WW USER MANUAL L005614 FOS TV FRESNEL WW USER MANUAL
intelligent temperature control system, improve the quality of our products stable
performance, apply to indoor installation.
Using brand LED chips, integrated encapsulation, improve reliability and long lifespan.
Using the advanced optical reflective material, make the light on the projection distance
and brightness is higher than traditional film soft light.
ⅡOVERVIEW AND DIMENSIONS
All dimensions are in millimeters
ⅢSAFETY INFORMATION
※Important
4. Keyboard available indicator.
ⅥDMX PROTOCOL
CH
Value
Function
CH1
000←→255
Dimmer, 0~100%
ⅦCOMMON INSTRUCTION
The light uses international 3 pins DMX signal cannon for DMX in and DMX out;
The light uses 4 numbers digital display to show the parameter. If there is no DMX in, the
display will in blank screen state when the buttons without press of the button after the 10
seconds. If the light has received the DMX in, the display will also in blank screen state, but
the indicate will has continuous regular flicker, it means the DMX signal has been correct
connected;
In fact, the light has 2 DMX channels, the 1st one is 0~100% linear dimmer, the 2nd one is
strobe, but the 2nd is closed in factory setting;
If there are no DMX in (without DMX console using) to light up the light, you can use the
control panel to set. Press MENU button until the display shows C255 , the light will full light
up. If you want to adjust the brightness of the light, you can use UP or DOWN button to
adjust and press ENER button to confirm the setting. The light will light up in the set state
when you power on next time;
This light uses intelligent full aluminium shell for the heat dissipation, through the electronic
temperature detection ensure the stability of the circuit at any time;
02
07

L005614 FOS TV FRESNEL WW USER MANUAL L005614 FOS TV FRESNEL WW USER MANUAL
When suspending the fixture above ground level, verify that the structure can hold at least
10 times the weight of all installed devices.
Verify that all external covers and rigging hardware are securely fastened and use an
approved means of secondary attachment such as a safety cable.
ⅤCONTROL PANNEL
BUTTON
MENU
UP
DOWN
ENTER
Call the main menu, or escape the current menu, (i.e. return to the
upper menu and give up the selected item or parameter).
Browse the menu item forward or increase the parameter.
Browse the menu item backward or decrease the parameter.
Confirm the selected item or parameter, (i.e. enter into the next menu,
or escape the current menu and save the selected item or parameter).
INDICATOR
There are 4 dots at the bottom of the digital tube, from left to right as:
1. DMX signal LED indicator;
2. Memory writing indicator, (Press ENTER after amending the DATA, This Dot will be light
up, it means the Data is saving);
3. Power indicator;
Every person involved with the installation, operation and maintenance of this device has to
be qualified and follow the instructions of this manual. Manufacturer will not with
responsibility for those operations which are not according to this Instruction.
Verify that the voltage matches the rated voltage.
When the voltage is 110V, Do not connect more than 10 lightings in total to AC mains
power in one interconnected daisy chain
When the voltage is 220V, Do not connect more than 20 lightings in total to AC mains
power in one interconnected daisy chain
Before using the fixture, check that all power distribution equipment and cables are in
perfect condition and rated for the current requirements of all connected devices.
Always ground (earth) the fixture electrically.
Avoiding hit the Light when you are move or install the light.
The minimum distance between light-output and the illuminated surface must be more
than 0.5 meters. Keep all combustible materials (for example fabric, wood, paper) at least
0.2 meters away from the fixture.
Do not expose the fixture to rain or moisture.
Avoid looking directly into the light source (especially those who suffer from epileptic fits)
Maximum ambient temperature (Ta) is 40°C. Do not operate fixture at temperatures higher
than this.
The Maximum surface temperature is 50°C
When suspending the fixture above ground level, verify that the structure can hold at least
10 times the weight of all installed devices.
Verify that all external covers and rigging hardware are securely fastened and use an
approved means of secondary attachment such as a safety cable.
ⅣPOWER CONNECTION
INSTALLING A NENUTRIK CONNECTOR ON A POWER CABLE
03
06

L005614 FOS TV FRESNEL WW USER MANUAL L005614 FOS TV FRESNEL WW USER MANUAL
Put bushing and chuck onto the cable.
Prepare cable as shown above. The power cable must is a three-conductor 2.5mm2 cable.
Insert the wire into the terminals and fasten the clamping device by a flat screw driver.
Push insert and chuck into housing (pay attention to the guiding keyway).
Fasten bushing.
The color-coding schemes and some possible pin identification schemes; if pins are not
clearly identified, or if you have any doubts about proper installation, consult a qualified
electrician.
RELAYING POWER TO OTHER DEVICES
The lightings can be linked in a chain by power cables which installed a blue and a
light-gray connectors on the two ends. The light-gray connector connects to the power out
socket of the first lighting, and the blue connector connects to the power in socket of the
subsequent lighting, and so on.
The power cable must is a three-conductor 2.5mm2 cable.
When the voltage is 110V, Do not connect more than 10 lightings in total to AC mains
power in one interconnected daisy chain.
When the voltage is 220V, Do not connect more than 20 lightings in total to AC mains
power in one interconnected daisy chain.
PHYSICAL INSTALLATION
This lighting can be placed on a horizontal surface such as a stage or clamped to a truss or
similar rigging structure in any orientation using a rigging clamp.
Wire color
Conductor
Symbol
Brown
Live
L
Blue
Neutral
N
Yellow/green
ground
04
05