Foundations 100-SSV User manual

Model 100-SSV
Stainless Steel Vertical Changing Station
Installation Instructions
• Failure to follow these warnings and the installation instructions could result in serious injury
or death.
• Read all instructions before installing diaper changing station. Keep these instructions. DO NOT
discard.
WARNING
SI260D
Thank you for purchasing a quality Foundations®product. Our goal is 100% consumer satisfaction!
If, for any reason you are not satisfied or if you have questions regarding your product or installation,
please contact our customer service team at 1-877-716-2757. Please DO NOT contact your distributor
or reseller as we are better prepared to assist you.

1
AD LT INSTALLATION REQ IRED.
TOOLS REQ IRED:
Level (A)
Measuring tape (B)
Power drill (C)
•READ ALL INSTR CTIONS BEFORE ASSEMBLY OF DIAPER CHANGING STATION
•Unpack carton and identify all parts.
ASSEMBLY INSTRUCTIONS
IMPORTANT: Due to widely varied wall material,
anchoring to be determined by architect or engineer.
A.D.A. Compl ance:
4.4.1 Maximum Protruding Objects
4.2.5 Forward Reach
4.2.6 Parallel Approach
4.27.4 Operation
Compliant when properly installed.
Door / wall plate to be
mounted on outside of
restroom door.
33-3/8
(848 mm)
30-3/8”
(771 mm)
(R)
33-7/8”
(860 mm)
(SM)
20-3/4”
(527 mm)
(Door)
Parts Description uantity
Door / Wall Plate 1
PARTS LIST
•This changer has six (6) recess mounting holes.
•The diaper changing station is no stronger than the anchors or walls to which they are attached and, therefore,
M ST be firmly secured in order to support the weight they are intended to support. It is recommended that this unit be
installed in a recessed fashion. If surface mounting, contact an architect, building contractor, or Professional Engineer
for proper installation and hardware. Contact an architect or building contractor if any questions.
•Child should never be left unattended.
•Avoid serious injury from falling or sliding out. Always use restraint system.
•Adding excessive weight such as parcels, packages, or accessories to the unit or to the bag hooks that exceed the total
weight limit of 50 pounds (22.7 kg) may cause the unit to be unstable or may cause a hazardous unstable condition to
exist.
WARNING
OPERATION:
Rotate base downward. Place infant on top of the changing surface. Use restraint system as described below. After child has been
changed, remove restraint system and rotate base back up against the wall.
USE OF RESTRAINT SYSTEM:
Place child so restraint strap is located at abdomen. Rotate top of buckle upward and insert strap
in buckle. Pull strap through buckle until snug against infant. Rotate top of buckle downward to lock
the strap into place. Slide red locking tab over top of buckle (F g. a). Reverse steps to loosen strap.
MAINTENANCE AND CLEANING:
Check all hardware and components monthly or as required to ensure hardware is tight and there
are no missing or damaged components. Take unit out of service if any component is missing or
damaged and contact customer service to order replacement parts. Do not substitute parts.
For replacement parts, contact customer service at 1-877-716-2757.
Clean by using a damp cloth with mild soap or mild multi-purpose cleaner. Do not use any strong
chemical cleaners or cleaning agents that may be hazardous to children.
ABC
F g. a
Locking
Tab
Top Of
Buckle

2
For A. D. A. compliance, top of lower double stud should be
30.5“ (78 cm) from the floor.
Recommended Block ng:
Wood double stud blocking is necessary. Contact an architect and
building official to make sure the blocking is adequate and complies
with building codes (F g. b).
1. Slide changer into blocking area and mark mounting hole location
on blocking studs.
HINT: This may require 2 additional people to help hold changer
in position while you are marking the locations.
2. Shim changer for a snug fit.
3. Align holes in changer with marked holes and secure using the
appropriate fasteners (F g. c).
NOTE: It is installers responsibility to provide correct fastereners
for other substrates.
4. Ensure all six (6) fasteners are tight.
INSTALLATION - RECESSED
INSTALLATION - SURFACE-MOUNT
Recommended Block ng:
If the walls do not have studs on center, then additional blocking is necessary
(F g. d).
Contact an architect or building contractor to make sure the blocking is adequate
and complies with building codes.
For A. D. A. compliance, measure up 62 3/4” (159 cm) from the floor and mark the
wall. This locates the position for the top left attachment hole.
NOTE:- Changer MUST be mounted to studs (F g. e).
- This unit incorporates a finishing collar that seats behind the changer’s
outside flange. Center the collar as the unit is being tightened against
the wall (F g. f).
F g. c
Recess
Mounting
Holes
Recess
Mounting
Holes Recess
Mounting
Holes
22-1/2" (571 mm)
Rough-in
Double Stud
Double Stud
Double Stud
Double Stud
34-1/8"
(867 mm)
Rough-in
3-7/8"
(98.6 mm)
1"
(25.4mm)
22-1/2"
(571 mm)
For A. D. A.
Compliance
30.5”
(78 cm)
TOP
VIEW
FRONT
VIEW
A. F. F
30-1/2”
(775 mm)
F g. b
F g. e
Surface-Mount
Holes
26"
(660 mm)
on center
16"
(406 mm)
on center
Top
For A. D. A.
Compliance
62 3/4”
(159 cm)
A. F. F
F g. d
F g. f
Collar
Unit
Wall