Foundations 100-SSC-R User manual

• Failure to follow these warnings and the installation instructions could result in serious injury
or death.
• Read all instructions before installing diaper changing station. Keep these instructions.
DO NOT discard.
WARNING
Model 100- C-R
Clad tainless teel Changing tation
Installation Instructions (Recessed Mount)
SI258R-D
Thank you for purchasing a quality Foundations®product. Our goal is 100% consumer satisfaction!
If, for any reason you are not satisfied or if you have questions regarding your product or installation,
please contact our customer service team at 1-877-716-2757. Please DO NOT contact your distributor
or reseller as we are better prepared to assist you.

1
ADULT IN TALLATION REQUIRED.
TOOL REQUIRED:
Level (A)
Measuring tape (B)
Power drill with 3/16” masonry bit (C)
Power screwdriver with bull nose phillips bit (D)
Truss head spanner bit (E)
•READ ALL IN TRUCTION BEFORE A EMBLY OF DIAPER CHANGING TATION.
•Unpack carton and identify all parts.
INSTALLATION INSTRUCTIONS
A.D.A. Compl ance:
4.4.1 Maximum Protruding Objects
4.2.5 Forward Reach
4.2.6 Parallel Approach
4.27.4 Operation
Compliant when properly installed.
•This changer has six (6) recess mounting holes.
•The diaper changing station is no stronger than the anchors or walls to which they are attached and, therefore,
MU T be firmly secured in order to support the weight they are intended to support. Contact an architect or building
contractor if any questions.
WARNING
21-3/8”
542 mm
13-1/8”
(333 mm)
34-3/4”
(883 mm)
(Door)
Parts Description uantity
Hardware for recessed installation:
3” x 1/4” Wood Screws 6
Door / Wall Plate 1
3” x 1/4” Wood Screws
PARTS LIST
Door / wall plate to be
mounted on outside of
restroom door.
AB
D
C
E

2
Recommended Block ng:
Wood double stud blocking is necessary. Contact an architect and
building official to make sure the blocking is adequate and complies
with building codes (F g. a.).
For A. D. A. compliance, top of lower double stud should be 30“
(76 cm) from the floor.
1. Slide changer into blocking area and mark mounting hole location
on blocking studs.
HINT: This may require 2 additional people to help hold changer
in position while you are marking the locations.
2. Use a power drill with a 3/16” bit and drill six (6) pilot holes in
the blocking studs.
3. Shim changer for a snug fit.
NOTE: If lower holes are inaccessible, remove plastic unit from steel
back by removing the 4 Truss Head Spanner Screws (f g. c). Once
steel back is attached to blocking, reconnect plastic wall to steel
back using the same spanner screws.
4. Align holes in changer with drilled holes and secure using the wood
screws. Wood screws have been provided and are for wood only (F g. b).
NOTE: It is installers responsibility to provide correct fastereners
for other substrates.
5. Ensure all six (6) screws are tight.
OPERATION:
Rotate base downward. Place infant on top of the changing surface. Use restraint
system as described below. After child has been changed, remove restraint system
and rotate base back up against the wall.
USE OF RESTRAINT SYSTEM:
Place child so restraint strap is located at abdomen. Rotate top of buckle upward and insert strap
in buckle. Pull strap through buckle until snug against infant. Rotate top of buckle downward to lock
the strap into place. Slide red locking tab over top of buckle (F g. d). Reverse steps to loosen strap.
MAINTENANCE AND CLEANING:
Check all hardware and components monthly or as required to ensure hardware is tight and there
are no missing or damaged components. Take unit out of service if any component is missing or
damaged and contact customer service to order replacement parts. Do not substitute parts.
For replacement parts, contact customer service at 1-877-716-2757.
Clean by using a damp cloth with mild soap or mild multi-purpose cleaner. Do not use any strong
chemical cleaners or cleaning agents that may be hazardous to children.
INSTALLATION
F g. b
Recess
Mounting
Holes
Recess
Mounting
Holes
Recess
Mounting
Holes
35 5/8" (905 mm)
Rough-in
Double Stud
Double Stud
Double Stud
Double Stud
3 7/8"
(98.4 mm)
1"
(25.4 mm)
19 5/8"
(499 mm)
Rough-in
35 5/8"
(905 mm)
For A. D. A.
Compliance
30”
(76 cm) A. F. F
18"
(457 mm)
F g. a
F g. c
Truss Head
Spanner Screws
F g. d
Locking
Tab
Top Of
Buckle
•Child should never be left unattended.
•Avoid serious injury from falling or sliding out. Always use restraint system.
•Adding excessive weight such as parcels, packages, or accessories to the unit or to the bag hooks that exceed the total
weight limit of 50 pounds (22.7 kg) may cause the unit to be unstable or may cause a hazardous unstable condition to
exist.
WARNING