Foxconn IOTGW-TIX01 User manual

IoT Gateway (IOTGW-TIX01)
User’s Manual
Ver. 1.0_2016Q4-A

2
About this Manual
Congratulations on purchasing the IoTGW-TIX01. This user manual provides detailed
descriptions of the hardware components and how to use the IoTGW-TIX01. Read this
manual carefully and follow the instructions while using the IoTGW-TIX01.
Copyright Information
No part of this manual, including the products and software described in it, may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into
any language in any form or by any means, except documentation kept by the
purchasers for backup purposes, without the express written permission of the
manufacturer.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe. All
trademarks are the property of their respective owners.
Copyright © 2016. All rights reserved.

3
Electronic Emission Notice
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
CE Notice
This device complies with the EMC directive of the European Community
and meets or exceeds the following technical standard:
EN 55022:1998 ”Limits and Methods of Measurement of Radio
interference Characteristics of information Technology Equipment.”
This device complies with the CISPR Class B standard
EN 55024:1998 ”Electromagnetic compatibilityGeneric immunity
standard Part1: Residential, and light industry.”
BSMI and NCC Notice
This equipment has been tested and found with BSMI and meets or exceed
the following technical standard:
The low-power radio-frequency devices must not be altered by changing
the frequency, enhancing emission power, adding external antenna, and
modification of original design characteristic as well as function.
The operation of the low-power radio-frequency devices is subject to the
conditions that no harmful interference is caused. The user must stop
operating the device immediately should harmful interference is caused
and shall not resume until the condition causing the harmful interference
has been corrected. Moreover, the interference must be accepted that may
be caused by the operation of an authorized communications, or ISM
equipment

4
Safety Information
Follow these safety instructions to avoid injury to self and damage to the IoTGW-TIX01.
To reduce the risk of fire or electric shock, install the unit in a
temperature-controlled indoor area free of conductive contaminants.
Do not place the unit near liquids or in an excessively humid
environment.
Do not allow liquids or foreign objects to enter the unit.
The unit does not contain any user-serviceable parts. Do not open the
unit.
Servicing, maintenance, and repair for this equipment must be
performed by qualified service personnel.

5
Table of Content
Introduction ......................................................................................................................... 6
Package Contents ................................................................................................................ 6
Interface of IoTGW-TIX01......................................................................................................7
Front Panel .........................................................................................................7
LED Definition.................................................................................................... 8
Rear Panel.......................................................................................................... 8
Installing and Connecting Your IoTGW-TIX01 ..................................................................... 9
To connect the IOTGW to the network and power on IoTGW-TIX01.............. 9
To connect the IoTGW-TIX01 to the computer and verify the IP address
assignment ........................................................................................................ 9
To verify IP address and prompted to log on .................................................10
To verify Wi-Fi configuration assignment........................................................ 10
To verify IOTGW configuration assignment:....................................................11
To verify the ZigBee sensors assignment:....................................................... 12
Appendix A Technical Information..................................................................................... 13
Technical Specification..................................................................................... 13

6
Introduction
IoTGW-TIX01 based for cloud application specifically focused in industrial or commercial
field, collects sensor via WiFi, Zigbee or BLE and transmitting data to cloud by 4G, WiFi
or Ethernet.
Package Contents
Please carefully check the IoTGW-TIX01 and the included accessories. If there is any
missing or damaged, please contact your dealer. Should you return the related items
and repacked using the original packing materials come with the unit.
No.
Item
Quantity
1
IoTGW-TIX01 Box
1
2
12V/1A AC Adapter
1

7
3
Quick Start Instructions
1
Interface of IoTGW-TIX01
The interface of IoTGW-TIX01 includes a LAN port, USB port and a Restart button as
shown below. The related function and indication of IoTGW-TIX01, please refer to the
following table.
Front Panel
The front of the IoTGW-TIX01 has the following indicators:
No.
Item
Description
A
ZigBee Pair
Button
Push the pairing button as if you pair the related ZigBee
sensor.
Use a pointed non-metallic object to press this button.
B
Power LED
Indicates whether AC power is available to the unit.
C
WiFi LED
Indicates the status of the wireless LAN.
D
ZigBee LED
Indicates the status of the ZigBee.
A
B
C
D

8
LED Definition
The function of the IoTGW-TIX01 is indicated by the Power LED, WiFi LED and ZigBee
LED as listed in the following tables.
LEDs
Normal
Abnormal
Transmission
Pairing
Power LED
ON
OFF
--
--
WiFi LED
OFF
ON(Fixed)
Flashing
--
ZigBee LED
OFF
ON(Fixed)
Flashing
Flashing
Rear Panel
The rear of the IoTGW-TIX01 has the following connectors and controls:
No.
Item
Description
A
USB port
USB host connector - future support for external USB
devices.
B
LAN port
Connectors for use with a computer LAN port.
C
DC Input port
Connector for the power adapter.
D
Restart button
Reset the IoTGW-TIX01 as if you power cycled the unit.
Use a pointed non-metallic object to press this button
Press 1 second: Restart system
Press 5 seconds: Reset to default password (admin)
Press 10 seconds: Reset to default value.
A
B
C
D

9
Installing and Connecting Your IoTGW-TIX01
To connect the IOTGW to the network and power on IoTGW-TIX01
1. Connect the LAN cable to the LAN connector and plug power cord into the
DC-Jack connector to turn on IoTGW-TIX01.
To connect the IoTGW-TIX01 to the computer and verify the IP address
assignment
1. Connect an active Ethernet cable to the LAN connector on the IoTGW-TIX01.
2. Configure the related network card setting (IP address: 192.168.1.xxx/24) of the
computer as shown below.
LAN IP: 192.168.1.101/24

10
To verify IP address and prompted to log on
1. Open your Web browser.
2. Enter: https://192.168.1.101
3. Log on as administrator. The default user name and default password are
“admin”. The IoTGW-TIX01 Web page displays.
To verify Wi-Fi configuration assignment
1. Select Wi-Fi Configuration from the Network menu. The Wi-Fi Configuration page
displays.
2. Select the appropriate SSID and enter the password to connect the Wi-Fi.
3. IoTGW-TIX01 will get the corresponding Wi-Fi information of SSID as shown
below.