foxunhd FX-MX05 User manual

Operating Instructions
www.foxunhd.com
FX-MX05
4K 4x4 HDMI Matrix
Dear Customer
Thank you for purchasing this product. For optimum performance and safety, please read these
instructions carefully before connecting, operating or adjusting this product. Please keep this manual for
future reference.
ABLE OF CONTENTS
Feature
Introduction
Specifications
Package Contents
Panel Descriptions
Connecting and Operating
Typical Application
Product Service
Warranty

Operating Instructions
www.foxunhd.com
Feature
Supports resolutions up to 1080p@60HZ,48-bit deep color, 4k@30HZ.
Allows any source to be displayed on multiple displays at the same time.
Allows any HDMI display to view any HDMI source at any time.
Dolby TrueHD and DTS-HD master audio pass through HDMI output.
Advanced EDID management for rapid integration of sources and displays.
Multiple switching mode, push-in button, IR remote control, and RS-232 control.
Easy installation with rack-mounting ears.
Full 3D pass- through.
INTRODUCTION
It is 4K HDMI Matrix 4x4, supports HDCP2.2. It offers HD video solution for super market, shopping mall;
HDTV, STB, DVD and projector factory; data control center; conference rooms; education and training;
luxurious house; home theaters etc.
SPECIFICATIONS
Bandwidth
2.97Gbps per color
Video Input Connectors
4xHDMI Type A, 19-pin, female, locking
Video Output Connectors
4xHDMI Type A, 19-pin, female, locking
RS-232 serial port
DB-9, female
IR Input ports
5x3.5mm stereo jack
IR Output ports
4x3.5mm stereo jack
Rack-Mountable
Rack ears included
Dimensions(WxHxD)
256MMx144MMx43MM, without feet
Weight
1.8 kg
Operating Temperature
-5 to +65℃(+23 to +149℉)
Storage Temperature
-4°F to 140°F (-20°C to 60°C)
Power Supply
12V/2A DC
Note: Specifications are subject to change without notice. Mass and dimensions are approximate.
PACKING CONTENTS
1. MX05.
2. 1x 12V2A DC power supply.
3. 1x Remote control.

Operating Instructions
www.foxunhd.com
4. 4x Wide Band IR cable
5. 4x IR TX cables.
6. 1x IR RX cables.
7. 1x mounting kit.
8. 1x CD for control software & user manual.
Notes: Please confirm if the product and the accessories and all in duded, if not please contact with
the dealers.
PANEL DESCRIPTION
Front Panel
1. IR receiver window----Receive the IR from the remote control of HDMI Matrix.
2. HDMI input selection button 1 to 4---Press to select the input from 1 to 4.
3. Input LED indicator---Indicate the status of the input for the matrix.
Rear Panel

Operating Instructions
www.foxunhd.com
①IR inputs 1 to 4 ---- 3.5mm stereo phone-jack.
②IR outputs 1 to4 ---- 3.5mm stereo phone-jack.
③IR extension receiver input ---- 3.5mm stereo phone-jack.
④Power switcher---- Press to power on/off the matrix.
⑤HDMI inputs 1 to 4----Connect HDMI sources.
⑥HDMI outputs 1 to 4----Output for displays, AVR etc.
⑦RS232 female port----Connect to the PC using RS232 cable.
⑧Power port---Use included DC adaptor to power the matrix switcher.
CONNECT AND OPERATE
1) Connect the HDMI input sources (such as HD-DVD, PS3, STB etc) into FX-MX05.
2) Connect the HDMI outputs (such as HD-LCD, HD-DLP) into FX-MX05.
3) Power on the input source you want to show.
4) Connect the power supply into FX-MX05 and turn on the display you want to watch.
5) Use remote or push the button to choose input source.
Attention: Insert / Extract cables gently.
Typical Application

Operating Instructions
www.foxunhd.com
Local IR remote control.
①Press "M" button to switch to "DIP Switch" mode for EDID Setting.
②OUTPUT-X select INPUT-Y:
A. Press OUTPUT-X (X means 1 to 4 of outputs) Press INPUT-Y (Y means 1 to 4 of inputs)
B. Press OUTPUT-X (X means 1 to 4 of outputs), Press the left and right arrow buttons to select the input.
③All outputs select INPUT-Y: Press ALL button in zone OUTPUT Press INPUT-Y button (Y means 1 to 4
of inputs), then INPUT-Y switched to ALL OUTPUTS.
④Mirror all inputs and outputs (Ex. Input 1 to output 1, input 2 to output 2, etc): Press PTP button in Zone
OUTPUT.
DIP Switch for EDID Setting
Press “M” button, switch to “DIP Switch” mode to choose the EDID.

Operating Instructions
www.foxunhd.com
DIP Switch
EDID
0000
1080P_2CH(PCM)
0001
1080i_ audio7.1
0010
1080P_ audio5.1
0011
1080i_2CH(PCM)
0100
1080i_audio7.1
0101
1080i_audio5.1
0110
1080P_3D_2CH(PCM)
0111
1080P_3D_ audio7.1
1000
1080i_3D_ audio5.1
1001
4K30Hz_2CH(PCM)
1010
4K30Hz_audio7.1
1011
4K30Hz_audio5.1
RS-232 Pin Assignment
Matrix
Remote Control Console
PIN
Assignment
PIN
Assignment
1
NC
1
NC
2
Tx
2
Rx
3
Rx
3
Tx
4
NC
4
NC
5
GND
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
Baud Rate: 57600 bps
Data Bit: 8-bit Parity: None Stop Bit: 1-bit
Flow Control: None
RS232 Control

Operating Instructions
www.foxunhd.com
Connect RS232 cable to PC, open the software ，choose the COM port and connect.
Click "General ", you can choose the HDMI input and for each HDMI out as below picture
Click "Advance", choose the "HDMI input", then click "PC Set EDID Mode" to set EDID,
such as video format, audio format etc. After setting the EDID, click "Apply" to finish the operation
Note: If you need change to "DIP Switch "mode for EDID setting , please press "M"
button on the remote controller.
IR extender control
User can use the IR receiver cable to change the IR receiver position.
If controlling the HDMI Matrix through the 1/8” (3.5 mm) input jack on the rear panel, connect the IR cable
directly to the matrix rear IR receiver extension sockets.
IR system
1) Control the sources from the sinks
Step1: Connect 4pcs “IR TX” cables to “IR TX” ports; connect 4pcs “IR RX” cables to “IR RX” ports
Step2: Affix the 4xIR emitter of “IR TX” cables to the IR window of the 4xHDMI source

Operating Instructions
www.foxunhd.com
Step3: Aim the remote control of HDMI source which you choosed to the “IR RX” cable which connected to
the Matrix.
For example:
If you choosed HDMI source1, then just aim the remote control of HDMI source1 to the “IR RX” cable which
connected to the Matrix.
2) Control the HDMI Matrix from “IR RX” port.
Aim the remote of the HDMI Matrix to the “IR RX” cable which connected to the Matrix.
MAINTENANCE
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner of benzine to clean this unit.
PRODUCT SERVICE
1) Damage requiring service: The unit should be serviced by qualified service personnel if:
(a)The DC power supply cord or AC adaptor has been damaged;
(b)Objects or liquids have gotten into the unit;
(c)The unit has been exposed to rain;
(d)The unit does not operate normally or exhibits a marked change in performance;
(e)The unit has been dropped or the cabinet damaged.
2) Servicing Personnel: Do not attempt to service the unit beyond that described in these operating
instructions. Refer all other servicing to authorized servicing personnel.
3) Replacement parts: When parts need replacing ensure the servicer uses parts specified by the
manufacturer or parts that have the same characteristics as the original parts. Unauthorized substitutes
may result in fire, electric shock, or other hazards.
4) Safety check: After repairs or service, ask the servicer to perform safety checks to confirm that the unit
is in proper working condition.
WARRANTY
If your product does not work properly because of a defect in materials or workmanship, our Company
(referred to as "the warrantor" ) will , for the length of the period indicated as below,
(Parts(2)Year ,Labor(90) Days) which starts with the date of original purchase ("Limited Warranty period"),
at its option either(a) repair your product with new or refurbished parts, or (b) replace it with a new of a
refurbished product. The decision to repair or replace will be made by the warrantor.
During the "Labor" Limited Warranty period there will be no charge for labor.
During the "Parts" warranty period, there will be no charge for parts. You must mail-in your product during

Operating Instructions
www.foxunhd.com
the warranty period. This Limited Warranty is extended only to the original purchaser and only covers
product purchased as new. A purchase receipt or other proof of original purchase date is required for
Limited Warranty service.
LIMITED WARRANTY LIMITS AND EXCLUSIONS
1) This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES
NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER
damages which occurred in shipment, or failures which are caused by products not supplied by
warrantor,or failures which result from accidents,misuse,abuse,neglect, mishandling, misapplication,
alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper
maintenance, power line surge, lightning damage, modification, or service by anyone other than a Factory
Service center or other Authorized Servicer, or damage that is attributable to acts of God.
2) THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER "LIMITED WARRANTY
COVERAGE".THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS
WARRNTY. (As examples, this excludes damages for lost time, cost of having someone remove or
re-install an installed unit if applicable, travel to and from the service, loss of or damage to media or images,
data or other recorded content. The items listed are not exclusive, but are for illustration only.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR
RESPONSIBILITY.