Franke ANMX330 User manual

MountingInstructionsandManual
Maintenance
Replacingthefilter
Youwillneed:
•3mmAllenKey
•Newfilter– B9094
1. Turnoffthewatersupply.
2. Removepanelusing3mmAllenkey.
I. Forwallhungversionremoveaccesspanel.
II. Forfloorstandingversionremovefloorstanding
shroud.
3. Disconnectfilterviathepushfitconnectors.
*Seebelow*
Recommendedreplacementoffilterevery6months.
HowSuperSpeedfit FittingsWork
Tomakeaconnection,thetubeissimplypushedinbyhand;theunique
patentedJohnGuestcolletlockingsystemthenholdsthetubingfirmlyin
placewithoutdeformingitorrestrictingflow.
Todisconnect,ensurethatthesystemisdepressurised andpushthecollet
squareagainstthefitting.Withthecolletheldinthispositionthetubecan
beremoved.
7
ANMX331 EA-Nr.: 7612979010848
Wall Hung Drinking Fountain with Bubbler, Bottle filler &
Water Filter
ANMX330 EA-Nr.: 7612979010831
Wall Hung Drinking Fountain with Bubbler & Water Filter
FrankeSissonsLtd.,Carrwood Rd,Sheepbridge,Chesterfield S419QB
T:+44‐(0)1246‐450255F:+44‐(0)1246‐451276E:[e-mail]
www.franke‐ws.com B0050

1
ImportantNotes
.Beforeinstallation,theinstructionshavetobereadandunderstood.
.Installation,commissioningandmaintenancearetobeperformedonlybya
qualifiedtechnicianaccordingtotheinstructionsprovidedandin
accordancewithlegalrequirementsandacknowledgedrulesoftechnology.
Important!
Beforeinstalling,flushthepipesincompliancewithDIN1988
6
GBRTechnicaldata
Minimumflowpressure1,0
Maximumoperatingpressure5bar
Recommendedflowpressure3bar
•Bubblerrequiresflatheadscrewdriver
•Bottlefillerrequires4mmallen key
Oncethedrinkingfountainisinstalled,the
flowratemayrequirealtering.
Todothissimplyadjustthepinlocatedat
thefrontofthewatercontrols.
Adjustingtheflowrate

No. Description QTY
1 Bubbler 1
2 BottleFiller(forANMX331/341) 1
36”Filter** 1
4 Fixingclip 1
5½”BSP–¼”Pushfitadaptor* 2/3
6¼”Pushfitelbow 2
7¼”Equaltee(forANMX331/341) 1
81Mlength¼”BlueLLDPETubing 1
9½”–3/8”Brassbush* 1/2
10 1¼”Wastebody 1
11 1¼”PTrap/Strap* 1
12 Fixingpack 1
Scopeofsupply
**Replaceevery6months,Partcode:B9094
*Quantitiesdependentonmodelpurchased
5 2
Mountingthewallhungdrinkingfountain
1. Placefixingbracketonwallensuringdistancefromflooris
15mmlowerthanrequiredheight.*RecommendedHeights:
Min685mm,Max915mm
2. Ensurebracketislevelandmarkoutthe5holecentres.
3. Removebracketfromwallanddrillholesusinga10mmdrill
bit.
4. Insertrawl plugsintowallandfixbrackettothewallbythe4
cornerholesusingthescrewsprovidedinpackB1125.
5. Forthecentralhole,insertremainingscrewthroughfilters
fixingclipandfixingbracket,intothewall.(Seeimage1)
6. Takeyourassembleddrinkingfountainandslideontothe
fixingbracketsecuringitinplaceviatheholesonthesides.
7. Connectthefiltertotheinletviathebottomaccesspanel.
Securepanelinplaceonceinstallationiscomplete.
Mounting

3 4
Dimensions
Pleasenotedimensionsaresameforversionswithoutbottlefiller
Assemblinginternalcomponents
Assemblingthedrinkingfountain
1. Undoallfixingscrewsandstripoffanyprotectivefilmthatmaynotbe
accessiblewhentheunitismounted.Removethefixingbracketand
bottomaccesspanel.
2. Removethebacknutfromthewaterbubblerandplaceitthroughthehole
providedonthetoppressingofthedrinkingfountain.Dependenton
customerpreferenceofwaterflowposition,therearetwoholesforthe
bubblertolocate.Refitthebacknutandtighten.
3. Fitthe½”–3/8”BSPbrassbushtothe½”BSP–¼”pushfitadaptor.Apply
asmallamountofthreadsealanttothethreadsofthebrassbushand
bubbler,thensecurethetwotogether.*ForANMX331variantplease
repeatprocessforthebottlefiller.*
4. Connectthewaterbubblerandthebottlefillertothefilterusingthepush
fitconnectorsandtubingsuppliedinpack,seediagramsforfurtherdetail.
5. Connect½”BSP–¼”pushfitadaptortoinletsupply.Fitrequiredamountof
tubingandan¼”elbowtoreachfilter.
*Seepage8forhowspeedfit fittingswork*
6. TakethewastebodyandsecureitontotheM6x40mmscrewonthe
bottomofthepressing.Thenattachthe1/¼”traptothewaste.
Diagram2:
Filterassemblyfor
ANMX331
Diagram1:
Filterassemblyfor
ANMX330