franklins FV034 User manual

Carefully run a small amount of PVA (wood glue) over
the exposed faces of the cleat. Push the Floating Shelf
cover onto the PVA covered cleat.
FORME FLOATING SHELF AND MIRROR (FV034):
Furniture Installation
Your new storage unit has been produced to the highest
possible standards. Please inspect your tray when
delivered prior to signing to ensure all is correct and not
damaged.
TOOLS:
Drill and drill bits
Spirit level
Tape measure
Caulking gun
Masking tape
Screws
Screwdriver
•
•
•
•
•
•
•
Silicone sealant
Cleaning materials
Pencil
Wall Board adhesive (No
More Nails)
3M Double sided mirror tape
PVA (or similar wood glue)
•
•
•
•
•
•
The timber cleat should be fitted to a solid horizontal
plate (minimum 75mm x 50mm) or vertical studs in the
wall using four 10g x 75mm countersunk screws.
STEP ONE:
Having established the position you want the floating
shelf mirror mark a level line on the wall where the base
of the mirror shelf will sit. Traditionally this is 1200mm
from the floor.
STEP TWO:
Find the horizontal plate, and wall stud or nog and
measure up from the pencil mark on the wall to identify
the positioning for four points (as per front page
diagram) where the screws will anchor the cleat to the
timber behind the wall.
Place wall board adhesive on
the back of the cleat; place
the cleat on the wall level with
the pencil mark.
Screw through the cleat in
the previously measured
positions into the wall studs
or nogs, leaving the screws
level with the face of the face
of the cleat. If you are unable
to locate anything solid in the
wall to fix the cabinet to, we
recommend that you use a
toggle or similar system.
FOR FURTHER INFORMATION:
Franklins
Head Office: 4-6 Waiouru Road,
Highbrook Business Park, Auckland 2013
P.O. Box 204426 Highbrook, Auckland
Telephone: [phone]
Email: [email protected]
Website: www.franklins.co.nz
STEP FOUR:
Place four 50mm pieces of double sided mirror tape
on to the back of the mirror, and if desired place four
or five dabs of silicon onto the back of the mirror for
extra adherence.
Place a small amount of silicon in the channel at the
back of the Floating Shelf, and carefully put the mirror
into the channel and push towards the wall. The
double sided tape and the silicon will hold your mirror
in place.
When the end of the mirror is flush with the end of the
back of the mirror cabinet, clean the excess silicon
from the channel of the floating mirror shelf and leave
for the wallboard adhesive and the silicon to set.
STEP FIVE:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. FAILURE TO COMPLY WITH THE INSTRUCTIONS WILL INVALIDATE THE WARRANTY
STEP THREE:
Timber Cleat

UNCOMPLICATED FRONT PANEL
REPLACEMENT:
An easy-find blue button makes
it simple to remove and reattach
a front panel. you can replace a
damaged front panel in a matter
of minutes, saving time, effort
and costs.
DRAWER INSTRUCTIONS:
REMOVAL AND REPLACEMENT
HINGE INSTRUCTIONS
ASSEMBLY AND FINE
ADJUSTMENT
Furniture Installation
The diagram below shows the adjustment screws for height and depth
adjustment of the cabinet doors.
Sophisticated hinge technology made by Hettich.
It’s external appearance indicates quality. Long service life and great ease of use
round off the hinge profile.
PLEASE READ THESE INSTRUCTIONS CAREFULLY. FAILURE TO COMPLY WITH THE INSTRUCTIONS WILL INVALIDATE THE WARRANTY
FAST, PRECISE FRONT PANEL
ADJUSTMENT:
A handy thumbwheel takes care
of height adjustmetn to +/- 2mm
it is practical, precise and tool
less. Side adjustment by +/-
1.5mm (from one side onle) is
equally simple.
FAST, PRECISE FRONT PANEL
ADJUSTMENT:
Adjustments to the angle of the
drawer front panel are also easy
and tool less. a gentle twist to the
railing is all that’s needed.
Concealed Latch
Simple
Safe
Reliable
•
•
•
Superflat cup design
Huge product
range
Over 100
mounting options
•
•
Eccentric depth
adjustment
Exact door depth
alighnment
Without loosening
screws
•
•
Eccentric height
adjustment
Exact door height
alighnment
Without loosening
screws
•
•
A drawer is inserted into the vanity by simply
locating it on the runners and pushing it in. Two
catches automatically lock the drawer onto the
runners, preventing accidental removal.
To remove the drawer, the catches are pressed
inward allowing the drawer to be pulled forward
and lifted off the runners.