FREEDEO TURBO SCREEN FD-T05F User manual

Add: 22F, Block C2, Nanshan Zhiyuan, No.1001 Xueyuan Road,
Nanshan District, Shenzhen, China
Email: [e-mail]
Website: www.timewaying.com
Tel: [phone]
Fax: [phone]
SHENZHEN TIMEWAYING TECHNOLOGY CO.,LTD.
Passive 3D Cinema System
TURBO SCREEN
Model No.: FD-T05F
Attention：Please review this User Manual carefully before installation.
Service Hotline：[phone]
User Manual

Contents
1. System Overview.........................................................................................1
2. System Features..........................................................................................2
3. Requirements on Cinema Environment........................................................2
4. Digital Projector Setting..............................................................................2
5. 3D System Components...............................................................................3
5.1 Turbo Screen Optical Unit........................................................................4
5.2 System Bracket.......................................................................................5
6. Installation of 3D System.............................................................................6
6.1 Installation of Cabinet Mount Components................................................6
6.2 Installation of Motorized Bracket..............................................................7
6.3 Installation of Lifting Gear and Optical Unit................................................8
7. System Connection......................................................................................9
7.1 System Connection..................................................................................9
7.2 LED status indicators.............................................................................10
8. System Positioning....................................................................................11
8.1 Set the Initial Position of Motorized Bracket..............................................11
8.2 Height and Angle Fine adjustment...........................................................12
9. System Optical Alignment..........................................................................13
9.1 The upper and lower beam position adjustment........................................13
9.2 Adjust middle beam image size................................................................14
10. Cautions...................................................................................................15

1/15 2/15
1. System Overview
TM
Freedeo Turbo Screen 3D cinema system is especially designed for the
cinema application. In cooperation with high quality 3D eyewear, the
system provides stunning 3D images for small or medium size audiences
on screens up to 20m wide.
The perfect optical designed Turbo Screen system can bring a smoother,
more immersive 3D experience to cinema audience, provide a higher
quality 3D device and reduce the cinema operational cost for cinema.
High Brightness:
The transmittance of the system is increased from 36% to 70% and the
light efficiency is increased up to 28% that even single projector can
support a big screen.
High Definition Image:
By adopting unique contrast-enhanced technology, the contrast rate
reaches up to 150:1 or above which bring you amazing 3D stereoscopic
images.
Smoother movie-going Experience
Fully support 24fps/48fps/60fps. Motion-blur can be dramatically reduced
that the system can deliver smooth motion and vivid picture quality to the
cinema audience.
Cost Saving:
With Turbo Screen system, cinemas can use lower brightness projector
bulbs for projection without sacrificing brightness, which reduces
operating costs.
More compatible:
Turbo Screen is suitable for projection hall with minimum projection
distance of 11 meters and supports 1:1.2 minimum throw ratio, enable you
to bring 3D image quality to nearly any size screen.
2. System Features
Electrical Features
Power supply: AC 100~240V 50/60 Hz
Sync Input: GPIO (37PIN) or 3D interface (15PIN)
Power consumption: 12W
Optical Features
Light transmittance: > 70%
Light efficiency: > 28%
Contrast: >150:1
Ghosting rate: <2 %
Frame rate: support 24fps/48fps/60fps
3. Requirements on Cinema Environment
Projection distance: 11~30m
Throw ratio: 1.2:1 or above
Polarized glasses: circular polarized 3d glasses
Silver screen gain: ≥2.4
Projection window glass: do not use tempered glass or polarized glass
Projection window size：>400*300mm
Distance between projector lens and window: >400mm
Projector lens diameter: < 150mm
4. Digital Projector Setting
Black Time: 450us
Delay Time: 0us

3/15 4/15
5. System components:
Each Turbo Screen system includes following components:
Optical Unit, System Bracket, Power Adapter, Power cord Box, SYNC
Cable, Motor Driving Signal Cable
Figure 5-1 System Components
Turbo Screen system size: 800*350*1050mm, total weight is about
32KG.Turbo Screen is composed of valuable optical elements. Please
handle with care to avoid damage.
Power cord Box
Optical Unit
System Bracket
5.1 Turbo Screen
Figure 5-1-1 Optical Unit
Optical Unit is composed of valuable optical elements. Dimensions：
282*96*360mm，weight about 10KG. It is an important part of Turbo
Screen that requires professional installation.
Light Incident Window
96mm282mm
360mm
Light Exit Window

5.2 System Components
Each Turbo Screen has a bracket to match with the projector stand. It can
be used to adjust the Turbo Screen's height, angle, left and right as well as
front and rear position to best fit the space of the Turbo Screen and
projector. It receives signal from projector through Signal SYNC Cable,
and identify the projector status of 2D or 3D, and move to the right
position.
Figure 5-2 System Components
5/15 6/15
380mm
1
100mm
2
3
3D projection position Sliding Rail
2D projection position
Motorized Bracket
Install fastener
Cabinet Mount Component
The distance between top
of mo ve a bl e b r a c k et an d
projector lens center is 380m
The distance between top
of moveable bracket and
projector lens is 100mm
Fix cabinet mount components to
the projector cabinet with clips
6. System Installation
6.1 Install cabinet mount components: adjust height and
length of cabinet mount components, and fix the components to the
projector cabinet with fastener, as shown in Figure 6-1.
Figure 6-1 Install Cabinet Mount Components

1
2
3
7/15 8/15
6.2 Install Motorized Bracket
Fix aluminum section (30*60*800mm) to the cabinet mount components
with L shape block, and then install the motorized bracket to the aluminum
section, as shown in Figure 6-2.
Figure 6-2 Install Motorized Bracket
6.3 Install lifting gear and optical unit
Fix lifting gear to the motorized bracket, and then install the optical unit
into the lifting gear, as shown in Figure 6-3.
Figure 6-3 Install lifting gear and optical unit
Fix Power box to cabinet
mount components
Install lifting gear to
the motorized bracket
Install the optical unit
into the lifting gear.
1
3
4
2
A. Fix aluminum section to the
cabinet mount components
with L shape block
B. Fix sliding rail to the aluminum section
Insert the nuts
The 2D position of projection system
is located on motorized bracket side,
please install it on the other side
which far away from projector lens

10/159/15
7. System Connection
7.1 System Connection
Optical Unit (MOTOR interface)------- Motorized bracket（Motor driving signal interface）
Optical Unit (SYNC interface) --------- Digital Projector (GPI / O or 3D Interface )
Optical Unit (POWER interface) ------- Power Adapter (24V 3.75A input)
Figure 7-1 System Connection
7.2 LED status indicators
After the connection is completed, turn on the system and digital projector
to play 3D movie, check the cables are connected correctly by observing
the LED status indicators on the front panel, as shown in Figure 7-2.
Figure 7-2 LED Status Indicators
POWER indicator:
when illuminate green, status ok. When off, check the power cord is
connected properly.
SYNC indicator:
When illuminated green, 3D signal is detected. When off, not detected,
check the 3D sync cable is connected properly and the projector is set
correctly.
L / R indicator:
When illuminated green, L/R polarity signal is detected. Press L / R button
to switch left/right picture if the screen image is not correct.
SY NCPO WER
ON /OFF L/R L/ R POWER MOTOR SY NC
SYNC indicator
L/R Signal Indicator LED
Power indicator
Turn on the system and digital projector to
play 3D movie, check the LED status indicator
L/R Polarity Switch
Power Switch
3
or
2
1
SY NCPO WER
ON /OFF L/R L/ R POWER MOTOR SY NC
Power Switch Power Input Interface SYNC Interface
L/R Polarity Switch Motor driving signal Interface
Connect motor driving
signal cable
M o t o r dr i v in g
signal Interface
Connect SYNC
GPI/O Interface
(37pin )
Connect digital
rojector
Connect power cord
100~240V AC Power Input
24V 3.75A Power Output
3D Interface
(15pin)

12/1511/15
8. System Positioning
8.1 Set the initial position of optical unit:
power on optical unit and the digital projector to play 3D movie, the
optical unit will move automatically to the side which close to the lens of
digital projector; Fine adjust optical unit position to align light incident
window right in front of digital projector lens, as shown in Figure 8-1.
Figure 8.1 Set the initial position of optical unit
8.2 Height and angle fine adjustment:
Turn on the digital projector and load cross calibration pattern from the
projector, briefly adjust position of up and down, left and right, center the
position of the pattern on the light exit window, as shown in Figure 8-2.
Figure 8-2 Adjust the Height and Angle of Lifting Gear
1
2
Rotate screw to
adjust the height
of lifting gear
Loosen screw to
adjust the angle
of lifting gear
Angle Range：30°
Height Range：50mm
2
1
3
Turn on the system to make
projector to play 3D movie
Projector Lens
Keep a space
of 5mm
Optical Unit
Adjust the motorized bracket position
to align light incident window right in
front of digital projector lens
Make the projector to play 2D movie,
check if the optical unit is out of
projector optical light path
The optical unit position
for play 3D movie
The optical unit position
for play 2D movie

SYNCPOWER
ON/ OFF
L/R L/R P OWER MOTOR SYNC
1
3
2
14/1513/15
9. System Optical Alignment
Clear 3D imagery synthesis depending on the upper and lower beam image
position and the middle beam image size.
9.1 The upper and lower beam position adjustment
Adjustment screws are located on the back of optical unit. Use left
adjustment screw to adjust up/down position of upper and lower beam.
Use right adjustment screw to adjust left/right position of upper and lower
beam, as shown in Figure 9-1-1.
Figure 9-1-1 Fold Mirror Adjustment
SYN CPOW ER
ON /OF F
L/R L /R POWE R MOTOR SYN C
1
2
3
4
Upper Beam
Middle Beam
Lower Beam
Block upper beam temperately
when adjusting lower beam
Block lower beam temperately
when adjusting upper beam
Upper Beam Adjustment Screw
Lower Beam Adjustment Screw
Remove screen protector
before adjustment
Adjust up/down
position of
upper beam Adjust left/right
position of
upper beam
Adjust up/down
position of
lower beam
Adjust left/right
position of
lower beam
Adjust upper beam
position to align the cross
calibration pattern
Adjust lower beam
position to align the cross
calibration pattern
Adjust the middle beam
image to align with upper
and lower beam image
Seal the adjustment
holes with adhesive
tape after installation
Adjusting middle beam
image size in left and
right simultaneously.
Middle Beam
Adjustment Screw
Middle Beam
Adjustment Screw
Position projector lens focuses on the screen, fine adjust upper beam and
lower beam position to coincide the cross calibration pattern align with
middle beam, when finish, adjust the size of middle beam image to center
align the whole page, as shown in Figure 9-1-2.
Figure 9-1-2 Apply the Correction by Adjusting the Fold Mirror
9.2 Adjust middle beam image size
The middle beam image size adjustment screws are located on both sides
of the light incident window. Adjust middle beam image to align with
upper and lower beam image, as shown in Figure 9-2.
Figure 9.2 Holes for adjusting middle beam image size

15/15
※Please operate under the guidance of professional personage.
Any damage caused by vandalism is NOT covered under warranty
10. Cautions
Remove screen protector from Turbo Screen after installation.
Use adhesive tape to seal the adjustment holes in the back of the system
after installation to avoid the optical elements get contaminated by dust.
The surface of Turbo Screen should be cleaned periodically. If the surface
becomes clogged by dust or the like, internal optical elements may be
contaminated.
Turbo Screen system is composed of precision optics with invisible
coating on the surface, use microfiber dust-free cloth and electronic-grade
ethanol to clean the light incident window and light exit window.
Check the light incident window and light exit window with bright light to
make sure all stain is gone.
Please turn off the power when system is not in use.
Turbo Screen system is frangible, do not throw or toss the system during
transportation.
Do not touch the light incident window and light exit window directly with
your hands.
Power off the system when it is not in use.
Please use Freedeo polarized 3D glasses when watching 3D movies, to
avoid ghosting and color cast problems.