Panasonic Lumix H-ES12060 Installation guide

Nano surface coating Yes
(from the focus distance reference line)
Operating temperature －10 ℃to 40 ℃(14 ℉to 104 ℉)
Mass (Weight) Approx. 320 ｇ(0.70 lb)
[AF/MF] switch Available (Switching AF/MF)
Overall length Approx. 86 mm (3.4 inch) (from the tip of the lens to the base side
of the lens mount)
Max. diameter Approx. 68.4 mm (2.7 inch)
“Micro Four Thirds Mount”
Angle of view 84°(Wide) to 20°(Tele)
Filter diameter 62 mm
(35 mm film camera equivalent: 24 mm to 120 mm)
Aperture type 9 diaphragm blades/circular aperture diaphragm
Maximum aperture F2.8 (Wide) to F4.0 (Tele)
Specifications
INTERCHANGEABLE LENS FOR DIGITAL CAMERA
“LUMIX DG VARIO-ELMARIT 12-60 mm/F2.8-4.0 ASPH./POWER O.I.S.”
Focal length
f=12 mm to 60 mm
ⓒPanasonic Corporation 2018 Unauthorized copying and distribution is a violation of law.
F22
Lens construction 14 elements in 12 groups (4 aspherical lenses, 2 ED lenses)
In focus distance 0.20 m (0.66 feet) to ∞(Wide) / 0.24 m (0.79 feet) to ∞(Tele)
Maximum image magnification 0.3×(35 mm film camera equivalent: 0.6×)
Optical image stabiliser Available
Minimum aperture value
[O.I.S.] switch Available (Switching ON/OFF)
Dust-proof and splash-proof Available
Mount
H-ES12060
Component Repair
Service Training Manual Ver.1.0
Internal use only

TABLE OF CONTENTS
1.1. Introduction
1.2. Important Notice
2 Ex
p
loded View
1.1. All Parts Exploded View
1.2. Parts Supply Form
3 Replacement Parts List
4 Service Fixture & Tools
4.1. Fixture and Tools
4.2. Clean Box
5 Maintenance
5.1. Dust / Dirt on the outer casing part(s)
5.2. Dust / Dirt on the Lens Glasses (Lens Cleaning)
5.2.2. Cleanin
g
p
rocedures of inside surface of the Lens
6 Disassembly and Assembly Instructions
6.1. Disassembly Instructions
6.1.1. Disassembly Flow Chart
6.1.2. Disassembly Procedure
6.2. Assembly Instructions
6.1.1. Assembly Flow Chart
6.1.2. Assembly Procedure
7 Adjustment
7.1. Matrix Chart for Re
p
laced Part and Necessar
y
Ad
j
ustment
7.2. Matrix Chart for Cleaning Portion and Necessary Adjustment
7.3. Flow Chart for Adjustment
7.4. Procedure for Adjustment
7.4.1. Service Fixture & Tools
7.4.2. Pre-setting
7.4.3. Projector / General-Purpose Camera / Repair Lens setting
7.4.4. 1st Lens Frame Adjustment
7.4.5. Electrical Adjustment
7.4.6. Procedure for Visual Checking (RP Chart)
7.4.7. Gluing
7.4.8. Procedure for Visual Checking (RP Chart)
8 Revision History
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 2
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 2
12
17
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 21
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 22
19
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
24
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 25
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
5
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
20
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 20
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 17
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 17
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 18
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 19
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
5
5
5
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
7
11
11
6
6
6
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
5.2.1. Cleaning procedures of outside surface of the Lens
PAGE
1 Service Navigation 1
1
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 1
2
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
4
4
4
3
22
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ 24
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・
5

1 Service Navigation
1.1. Introduction
This manual contains technical information, which allow service personnel's to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
1.2. Important Notice
This manual is written for Micro Four Thirds Lens H-ES12060.
As you may know, lens hates dust, soil, sand, fingerprint. So that, you have to repair (disassembly / assembly)
with close attention. Or you have received customer complaint.
・Use in the clean room / clean box. (At least class 10000)
This repair method isn't the exact same as factory production line. So please obey description in this manual, definitely.
Especially,
・Disassembly / assembly order
・Screw torque
・Screw order
1

2 Exploded View
2.1. All Parts Exploded View
2.2. Parts Supply Form
The following part is supplied in a form different from the Exploded View.
Ref. No. 225 ：CAM BARREL UNIT
201
203
204
205
206
208 209
210
206
B214
B211
B213
B210
B214
B212
B215
B208
B209
B204
B205
225
226
227
228
B206
B207
B201
B203
B202
202
B221
B222
B223
224
221 222 223
222-1
225
For the repair part protection
Dispose of it when replacing the part
2

3 Replacement Parts List
Definition of Parts Supplier
・All parts are supplied from PAVCX.
1
203 6OU1HES12060Z ZOOM RING UNIT 1
215 VQL1V24 WEEE LABEL 1
204 DVMH1028Z ZOOM DRIVE PIN 1
205 DVUS1002Z REAR FRAME EARTH SPRING 1
206 6SE2Z260Z
226 ----- WAVE WASHER 1 (NOT SUPPLIED)
227 5OU1HES12060Z
Remarks
201 1HR1Z260CZ DECORING UNIT 1
Ref.No.
DVOR1028Z
Part No. PcsPart Name & Description
210 SHADING FRAME 1
202 DVGX1028Z FILTER RING
222-1 DVMH1024Z 2ND LENS SHADING PLATE 1
225 4OU1HES12060Z CAM BARREL UNIT 1
B221 - B223 VHD2096 SCREW 3
209 SXQ0649 L MOUNT UNIT 1
222 3OU1HES12060Z 2ND LENS FRAME UNIT 1
223 3DX4Z260Z 3RD LENS FRAME2 UNIT 1
224 5DE5Z260Z 5TH LENS FRAME UNIT 1
B215, B216 VHD2246 SCREW 2
B211 - B213 VHD2299 SCREW 3
B214 VHD2298 SCREW 1
B206, B207 VHD2073 SCREW 2
B204 SHD0021 SCREW 1
L MOUNT CONTACT UNIT 1
207 RDE4Z260Z REAR FRAME UNIT 1
208 SMG0095-M DUSTPROOF RUBBER 1
221 2OU1HES12060Z 1ST LENS HOLDER UNIT 1
215 VQL1W22 TEN TEARS LABEL 1
RING MOUNT BASE UNIT 1
228 1PB1DV1018Z LENS P.C.B. UNIT 1
B205 VHD2011 SCREW 1
B201 - B203,
B208 - B210 VHD2296 SCREW 6
3

4 Service Fixture & Tools
4.1. Fixture and Tools
The following Fixture and Tools are used for checking and servicing this unit.
4.2. Clean Box
The repair quality is considered, and it is recommended working in the environment of satisfied clean level
less than class 10,000 (Federal Standard 209D).
Reference Camera / Lens
RFKZ0422 DMC-GM5 / H-FS12032
Lens Cleaning Kit Torque Driver Torx Driver (for Adjustment) Blower
VFK1900BK RFKZ0542 RFKZ0609
＊Only supplied 10 set/box.
Glove Cloth Collimeter
＊T3 type
Lens Projector for Adjustment Lens Adaptor Projector Chart Lens Control Adaptor
SUKZ000030 SUKZ000031 SUKZ000032 SUKZ000033
Rp-Chart (L-size) Rp-Chart (M-size)
SUKZ000034 SUKZ000035
4

5 Maintenance
5.1. Dust / Dirt on the outer casing part(s)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up the outer casing part with the dry fuzz-free cloth.
5.2. Dust / Dirt on the Lens Glasses (Lens Cleaning)
5.2.1. Cleaning procedures of outside surface of the Lens
1. Blow off the dust on the Lens glass surface with the Blower, gently. (Do not blow strongly.)
2. Wipe out the dirt on the Lens glass surface with Lens Cleaning Kit (VFK1900BK) if necessary.
(Consult the instruction sheet which is included in the Lens Cleaning Kit in details.)
5.2.2. Cleaning procedures of inside surface of the Lens
1. When removing the each above unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "4.2. Clean Box", in details.
【Cleaning Instruction】
Wipe the Lens surface with
cleaning sheet starting
from centre towards to
outside in a circular motion.
1st Lens Holder Unit
2nd Lens Frame Unit 3rd Lens Frame2 Unit
5th Lens Frame Unit
5

6 Disassembly and Assembly Instructions
6.1. Disassembly Instructions
6.1.1 Disassembly Flow Chart
Wave Washer
8Zoom Drive Pin Zoom Ring Unit
Ring Mount Base Unit
2 Filter Ring
7
1 Decoring Unit
9
Lens Unit
3 Shading Frame
4 L Mount Unit
5Dustproof Rubber
Rear Frame Unit
6L Mount Contact Unit
Lens P.C.B. Unit
Rear Frame Earth Spring
13 5th Lens Frame Unit
Come Barrel Unit
12 3rd Lens Frame2 Unit
10 1st Lens Holder Unit
11 2nd Lens Frame Unit
2nd Lens Shading Plate
Attention
If you do the disassemble procedure after this,
it requires the disassembly of No.1 and No.2.
(For adjustment after assembly)
6

Im
p
ortant：
It must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000
(Federal Standard 209D))
2. Remove the L Mount Unit.
3. Insert the small flat blade screwdriver to Gap (between
the Decoring Unit and lens glass), and peel off
the Decoring Unit gently.
6.1.2.2. Removal of the Filter Ring 6.1.2.4. Removal of the L Mount Unit
1. Remove 3 screws (A) and the Filter Ring. 1. Remove screw (C) and 3 screws (D).
6.1.2. Disassembly Procedure
6.1.2.3. Removal of the Shading Frame
1. Remove 2 screws (B) and the Shading Frame.
6.1.2.1. Removal of the Decoring Unit
1. The Decoring Unit is sticked on the Filter Ring.
2. Put the sheet so that the lens glass is fullty covered.
Screw (A) ｘ3
Screw (A)
Screw
(
B
)
Screw
(
B
)
ｘ2
Screw
(
C
)
Screw
(
D
)
Screw (C) Screw
(
D
)
ｘ3
7

6.1.2.5. Removal of the Dustproof Rnbber
2. Remove 2 screws (F) and the Lens P.C.B. with
1. Remove the Dustproof Rubber. the L Mount Contact Unit.
3. Remove 3 screws (E) and the Rear Frame Unit.
6.1.2.6. Removal of the Lens P.C.B. Unit and
3. Remove the L Mount Connect Unit from Lens P.C.B..
the L Mount Contact Unit
1. Disconnect the 4 Connectors of the Lens P.C.B..
2. Disconnect the Connector of the Lens P.C.B..
and the Rear Frame Unit
Connector
Dustproof Rubber
Screw
(
E
)
Screw
(
E
)
ｘ3
Connector
Connector Connector
Connector
Screw
(
F
)
Screw
(
F
)
ｘ2
8