FREEWAY MT700-24T Assembly instructions

INTRODUCTION
Thank you for purchasing Freeway Med-Tech’s Medical Grade Monitor. With a 24-inch display and optional
integrated batteries, the Medical Grade Monitor offers optimal combinations of performance and power
savings. With fully-integrated point-of-care modules within an elegant, space-saving design, the Medical Grade
Monitor is the optimum solution to enhance workow and service, while paired with NHS Hospital Standard
MFF PC, or thin clients.
Please take a few moments to review the contents of this document to ensure that the setup and startup
proceed smoothly. The Monitor is ready for use, out of the box, in its default conguration when powered
by the power source provided. The following documentation offers guidance on the hardware elements
and features of the monitor. Please refer to your device provider for information pertaining to the software
operating system or software applications.
The MT700-24T supports VESA standard (100x100mm) mounting brackets and arms. Attach the bracket or
the arm to the back of MT700-24T, then use screws (4 x M4x12mm) to fix the VESA bracket or arm.
BASIC
OPERATION
GUIDE
MT700 -24T
Battery powered Monitor
Package contents
1 MT700-24T Battery
Powered 24in Touch
Screen Monitor
1-3 MT202 Li-ion batteries
(qty dependant on
order spec)
1 Medical Grade AC-DC
power adapter with
orange curly power cord
1 Basic Operation Guide
1 Cable Pack – including
HDMI, Dell DC out
(19V) USB Touch / USB
Hub / WiFi x 2

BASIC FEATURES
The Monitor integrates a bright 24in display with a high performance system, USB ports, and integrated
options such as capacitive touch, hot-swappable batteries, and smart card reader for a comprehensive point-
of-healthcare solution.
Powering ON and OFF
If your Monitor comes with the battery packs, please open the battery slot caps and then put in the battery
packs one by one. If not, please use the AC-DC adapter with the Monitor for the power supply. To activate
the Monitor, push and quickly release the Power Button and the display will come on in a few seconds. To
put in Standby mode, push and quickly release the Power Button. To turn off for extended storage, power
off the device safely using any software function that “shuts down computer” provided in the software
operating system.
PRECAUTIONS
• Always exercise care when operating and handling
the Monitor.
•Never disassemble any portion of the enclosure, as
this will void any product warranty on the Monitor.
• Do not use any AC/DC adapter other than the
one provided with the device or a replacement
acquired from the manufacturer.
• In the unlikely event that smoke, abnormal noise or
strange odour is present, immediately power down
the Monitor and disconnect all power sources.
Please report the problem to your device provider
immediately.
Power/Battery LED Status
•Blue indicates the battery is 25% to 100% charged
•Blinking blue indicates the battery is charging
•Orange indicates that the battery is between 11% to25%
•Blinking Orange indicates that the battery is below 10%
Wireless Networking
Wireless LAN
The Monitor is often delivered with an embedded (user-inaccessible) 802.11ax WLAN adapter equipped with
a hidden custom antenna.
•Through the support of typical WLAN adapters, the Monitor should be able to detect all 802.11 access
points in the vicinity for you to select the access point of your choice for connection.
•The SSID and WEP/WPA/WPA2 (if enabled) parameters on the Monitor and the access points have to
match. The SSID is case-sensitive and it is recommended that you enable WEP/WPA/WPA2 encryption (or
advanced alternatives) for secure access.
•When WEP/WPA/WPA2 is enabled, you may need to consult your network administrator or your
networking equipment literature to properly congure associated settings such as Authentication mode, etc.
•Refer to the access point operating manuals for setting up the 802.11 access points.
Bluetooth
The Monitor features a built-in Bluetooth adapter that operates on the Microsoft Windows Bluetooth
protocol. The Bluetooth conguration application is invoked from the System Tray or from the Control
Panel. Follow the instructions and options provided within the application to congure and invoke Bluetooth
connectivity with the corresponding peripherals.
CLEANING THE MT700-24T MONITOR
You can clean the MT700-24T as often as required. All health care institutions will have a recommended
minimum frequency for routine cleaning of various items within their facility. This may be weekly, daily or after
each use depending on the risk involved.
The screen
•An antibacterial cleaning solution (70% alcohol) that is non-abrasive can be used to clean the touch screen.
•Cleaning with a micro-ber cloth is recommended.
• Please spread the solution onto the cloth and then clean the touch screen.
•It is recommended to wipe the screen in a top to bottom motion and nish across the bottom to minimise
streaking and to prevent excess moisture running down off the bezel.
The anti-microbial enclosure
•Use a soft/non-abrasive cloth moistened with cleaning solution (70% alcohol) to clean the enclosure.
• To prevent scratching the anti-microbial coating, please wipe gently.
IMPORTANT NOTES
1. The battery packs (optional) shipped with your
device may be low in power - please use the AC-
DC adapter with the Monitor when setting up the
device for the rst time to fully charge the battery
packs. You may charge the battery packs with them
attached to the Monitor or with the optional battery
charger kit.
2. When the battery packs are charging, the blue-
coloured Battery LED should blink slowly. If plugging
in the AC-DC adapter does not trigger this blinking
activity and the LED stays dark, the battery pack(s)
may have been drained substantially. Try unplugging/
plugging in the AC-DC adapter to the Monitor a few
times to activate the charging process.
3. To conserve power, use (push and quick release)
the Power Button to put the device in “Standby”
mode while not in use. Pushing briey on the same
button will wake up the system within seconds.
4. Avoid using the Power Button (“hold 4+ seconds”
feature) to turn off the device—this form of
hardware shutdown is intended to be a means of
recovery from device lockups, and not as normal
operation.
5. If connecting an external monitor to the Monitor
(via HDMI port), you must power the Monitor with
the provided AC-DC power adapter.
freewaymedtech.com MT700-24T Basic operation guide
Battery status LEDs

A C G H I
LJ K LNM
EB D
Battery packs (optional)
FRONT REAR
100x100 VESA mounting
F
TOUCH
SCREEN
I/O PORTS
The MT700-24T Monitor has a comprehensive set of I/O ports. The following ports are located along
the lower rear edge of the unit.
v2.0 0322freewaymedtech.com
Caution: Disposal of a battery into re or a hot oven, or mechanically crushing or
cutting of a battery, that can result in an explosion. Leaving a battery in an extremely
high temperature surrounding environment that can result in an explosion or the
leakage of ammable liquid or gas.
*The monitor’s enclosure may look
different to production models.
ADC-outputs HUSB Type-B for touch screen connection
BDC-in IWi-Fi antennas
CUSB Type-B input JPower button
DCOM Ports (optional) KFunction buttons
EUSB 3.0 LStereo speaker
FUSB 2.0 MReading light on/off button
GHDMI (1.4a) NLED reading light